• 한국지반환경공학회 논문집
• /
• 제25권6호
• /
• pp.5-12
• /
• 2024

현재 저수지 제체의 차수성 및 안전성 확보를 위해 약액을 저압으로 주입하여 제체 손상을 최소화하는 그라우팅 공법이 보편적으로 사용되고 있으나, 내구성 확보와 체계적인 고화재의 배합비 결정방법이 정립되어 있지 않은 문제들이 있다. 본 연구에서는 원지반과 고화재를 다양한 중량비율로 교반·혼합하였을 경우 혼합체의 투수계수와 강도를 실내시험을 통해 확인하였으며, 시험결과들의 분석을 통해 최적 배합비를 제안하였다. 실내실험을 위한 공시체는 고화재의 배합량을 고려하여 제작하였다. 투수시험용 공시체는 사질토와 점성토 별 고화재 배합량 1.5kN/m³에 대해 제작하였으며, 투수시험 결과 차수 성능이 확보되어 각종 설계기준을 만족하는 것을 확인하였다. 강도시험을 위한 공시체는 점성토의 경우 5가지, 사질토는 3가지 배합비로 각각 3개 총 24개의 시편을 제작하였으며, 시험 결과 사질토와 점성토 모두 배합량 2.0kN/m³ 이하에서는 일축압축강도가 재령일이 증가함에 따라 선형적으로 증가하는 경향을 나타냈다. 따라서 현장에 적용되는 최적의 배합비는 고화재 배합량을 1.5kN/m³ 및 2.0kN/m³으로 결정하였다. 또한 현재 운영 중인 노후 저수지 개보수사업 설계사례를 대상으로 실험성과를 반영한 수치해석을 실시한 결과 저수지 제체의 차수 및 안전성 증대 효과를 확인하였다.

• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.85-95
• /
• 2015

PURPOSES : Recently, bonded concrete overlay has been used as an alternative solution in concrete pavement rehabilitation since its material properties are similar to those of the existing concrete pavements. Deteriorated concrete pavements need rapid rehabilitation in order to prevent traffic jams on Korean expressways. Moreover, speedy and effective repair methods are required. Therefore, the use of bonded concrete overlay with ultra-rapid hardening cement has increased in an effort to reopen promptly the expressways in Korea. However, mobile mixer is required for ultra-rapid hardening cement concrete mixing in the construction site. The use of mobile mixer causes various disadvantages aforementioned such as limitation of the construction supply, open-air storage of mixing materials, increase in construction cost, and etc. In this study, therefore, hydration accelerator in-situ mixing on polymer modified concrete produced in concrete plant is attempted in order to avoid the disadvantages of existing bonded concrete overlay method using ultra-rapid hardening cement. METHODS : Bonded concrete overlay materials using ultra-rapid hardening cement should be meet all the requirements including structural characteristics, compatibility, durability for field application. Therefore, This study aimed to evaluate the application of hydration accelerator in-situ mixing on polymer modified concrete by evaluating structural characteristics, compatibility, durability and economic efficiency for bonded concrete overlay. RESULTS : Test results of structural characteristics showed that the compressive, flexural strength and bond strength were exceed 21MPa, 3.15MPa and 1.4MPa, respectively, which are the target strengths of four hours age for the purpose of prompt traffic reopening. In addition, tests of compatibility, such as drying shrinkage, coefficient of thermal expansion and modulus of elasticity, and durability (chloride ions penetration resistance, freezing-thawing resistance, scaling resistance, abrasion resistance and crack resistance), showed that the hydration accelerator in-situ mixing on polymer modified concrete were satisfied the required criteria. CONCLUSIONS : It was known that the hydration accelerator in-situ mixing on polymer modified concrete overlay method was applicable for bonded concrete overlay and was a good alternative method to substitute the existing bonded concrete overlay method since structural characteristics, compatibility, durability were satisfied the criteria and its economic efficiency was excellent compare to the existing bonded concrete overlay methods.

• Journal of Theoretical and Applied Mechanics
• /
• 제3권1호
• /
• pp.45-65
• /
• 2002

A constitutive model on oorthotropic thermo-elasto-viscoplasticity for fiber-reinforced composite materials Is illustrated, and their thermomechanical responses are predicted with the fully-coupled finite element formulation. The unmixing-mixing scheme can be adopted with the multipartite matrix method as the constitutive model. Basic assumptions based upon the composite micromechanics are postulated, and the strain components of thermal expansion due to temperature change are included In the formulation. Also. more than two sets of mechanical variables, which represent the deformation states of multipartite matrix can be introduced arbitrarily. In particular, the unmixing-mixing scheme can be used with any well-known isotropic viscoplastic theory of the matrix material. The scheme unnecessitates the complex processes for developing an orthotropic viscoplastic theory. The governing equations based on fully-coupled thermomechanics are derived with constitutive arrangement by the unmixing-mixing concept. By considering some auxiliary conditions, the Initial-boundary value problem Is completely set up. As a tool of numerical analyses, the finite element method Is used with isoparametric Interpolation fer the displacement and the temperature fields. The equation of mutton and the energy conservation equation are spatially discretized, and then the time marching techniques such as the Newmark method and the Crank-Nicolson technique are applied. To solve the ultimate nonlinear simultaneous equations, a successive iteration algorithm is constructed with subincrementing technique. As a numerical study, a series of analyses are performed with the main focus on the thermomechanical coupling effect in composite materials. The progress of viscoplastic deformation, the stress-strain relation, and the temperature History are careful1y examined when composite laminates are subjected to repeated cyclic loading.

• 한국농공학회논문집
• /
• 제56권4호
• /
• pp.21-28
• /
• 2014

In this study, evaluated ware the strength and durability of the vegetated water purification channel concrete to which recycled aggregates, hawang-toh and jute were applied. Box-Behnken method of response surface analysis in statistics was applied to the experimental design. Experimental variables are as follows, recycled coarse aggregates, hawang-toh, blast-furnace slag and jute fiber. In the experiment, conducted were the tests of compressive strength, chloride ion penetration, abrasion resistance and impact resistance the replacement rate effects of the recycled aggregates, blast-furnace slag and hwang-toh on the performance of vegetated water purification channel concrete were analyzed by using the response surface analysis method on the basis of the experimental results. In addition, an optimum mixing ratio of vegetated water purification channel concrete was determined by using the experimental results. The optimum mixing ratio was determined to be in 10.0% recycled coarse aggregates, 60.0% blast-furnace slag, 10.1% hwang-toh and 0.16% jute fiber. The compressive strength, chloride ion penetration, abrasion rate, and impact number of fracture test results of the optimum mixing ratio were 24.1 MPa, 999 coulombs, 10.30 g/mm3, and 20 number, respectively.

• Macromolecular Research
• /
• 제13권5호
• /
• pp.367-372
• /
• 2005

As a preliminary work for the preparation of nylon 6/c1ay nanocomposites by reactive extrusion, nylon 6/c1ay nanocomposites were prepared by anionic polymerization in a flask. In order to investigate the effect of the intercalation of clay layers, the clay feeding times, such as in pre-mixing where the clay was fed before initiation of polymerization and in after-mixing method where the clay was fed after initiation of polymerization, were changed. The appearance of the WAXD peak of nanocomposites prepared by the pre-mixing method was obvious and the tensile strength was decreased compared with that of pure nylon 6, which indicates that the clay layers were not dispersed and distributed. During the preparation of the nanocomposites by the after-mixing method, disordering of the clay layers was observed with increasing clay addition time and was suspected to result from the rapid polymerization of nylon 6 within the clay layers.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 논문집 센서 박막재료연구회 및 광주 전남지부
• /
• pp.73-74
• /
• 2008

In this paper, we have investigated dispersibility, volume resistivity of nano-composite by solution mixing method. Dispersibility measured by FE-SEM(Field Emission Scanning Electron Microscope. And volume resistivity measured by ASTM D991. To expect interaction used dual filler system. But, dual filler system had influence on polymer complex. So, polymer chain mobility doesn't resist.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.835-840
• /
• 2000

The purpose of this study is developing concrete Mixing & placing method that could be adjusted to vertical joint at top-down method. Basic test was consists of general, high fluidity, and high quality mixing concretes and Mock-up test had several placing ways, placing positions. They were examined several placing ways, placing positions with Mock-up model comparison with three mixing concrete to know fluidity characterics. Used with Mock-up model to know packing ability from placing ways and positions. The result of the study like this; High fluidity and High quality concretes show favorable packing ability, especially, in sheath placing way. It was expected to good result in next planned real structure test.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.489-492
• /
• 2005

The Purpose of this study is to develope the method for early recovery of the biodiversity in the oligotrophical costal area. The result of this study, the dissolution ratio is superior in the case which the cement coating thickness of the granular fertilizer is below 1mm. From the failure-side it is judged with the fact that appropriate to use the separate charging method and vibration compaction method. For the cases of the mixing ratio of cement coating granular fertilizer, there was not any clear tendency for the change of the strength up to 20$\%$ of the mixing ratio. However, at the 30$\%$ mixing ratio, decrease of the strength was noticed. So it can be concluded that the stability can be achieved in the range of 20$\%$ and below.

• 태양에너지
• /
• 제19권4호
• /
• pp.21-31
• /
• 1999

This paper presents a quasi-three-dimensional calculation method considered a spanwise mixing effect in a diagonal flow impeller. The effect of this spanwise mixing caused by spanwise distribution of blade loading is evaluated by a secondary flow theory. In order to verify the validity of this method, it is applied to the analysis of a diagonal flow fan designed under a vortex type of constant circumferential velocity and that of a free vortex. The comparison of the calculated result with experimental data shows a good agreement except the regions near the casing where the flow field is affected by the tip leakage flow.

• 한국공작기계학회논문집
• /
• 제17권5호
• /
• pp.95-100
• /
• 2008

An active micro-mixer, which is composed of an oscillating micro-stirrer in the micro-channel to provide effective mixing was optimized. The effects of molecular diffusion and disturbance by the stirrer were considered with regard to two types of mixer models: the simple straight micro-channel and micro-channel with an oscillating stirrer. Two types of mixer models were studied by analyzing mixing behaviors such as their interaction after the stirrer. The mixing was calculated by Lattice Boltzmann methods using the D2Q9 model. In this study, the time-averaged mixing index formula was used to estimate the mixing performance of time-dependent flow. The mixing indices of the two models were compared. From the results, it was found that the mixer with an oscillating stirrer was much more enhanced and stabilized. Therefore, an approximate optimization of an active micro-mixer with an oscillating stirrer was performed using Kriging method with OLHD(Optimal Latin Hypercube Design) in order to determine the optimal design variables. The design parameters were established as the frequency, the length and the angle of the stirrer. The optimal values were obtained as 1.0346, 0.66D and $\pm45^{\circ}$, respectively. It was found that the mixing index of the optimal design increased by 88.72% compared with that of the original design.