• International Journal of Air-Conditioning and Refrigeration
• /
• v.11 no.3
• /
• pp.140-149
• /
• 2003

In these days, environmental concerns have been increased throughout the industry and community worldwide. To prevent the ozone depletion, ozone depletion potential of a refrigerant must be zero. Simultaneously, a refrigerant with low GWP (global warming potential) is very demanding to reduce green house effect. Chlorine-free HFC-l34a is a refrigerant widely used for automotive air-conditioning system because its destruction potential is ecologically zero. Although HFC-l34a has no ozone depletion potential, its global warming potential is so high that it is not considered as a perfect alternative refrigerant that is acceptable for long-term use. In this paper, experimental measurement has been carried out to analyze the performance characteristics of automotive air-conditioning system using HFC-152a, which has low GWP and zero ODP. Also mixed refrigerant that is composed of HFC-152a and $CF_3$ was applied to investigate an alternative possibility for the automotive air-conditioning system. As a result of this study, we could draw following conclusions; With respect to the variation of the rotational speed of compressor, outside air temperature and flow rate, the heat amount of evaporator and compressor and performance coefficient was varied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.189-192
• /
• 2004

To improvement life-time of the organic light emitting diodes(OLEDs). We investigate the inorganic composite film based on MgO and $SiO_2$ to protect from the moisture and oxygen. The inorganic composite films are added the base materials to the co-operate materials using the mixed process and it is deposited on plastic substrate by e-beam evaporator. In order to analyze as kinds of inorganic materials, Water Vapor method of Transmission Rate (WVTR) and Oxygen Transmission Rate (OTR) are measured by Permatran equipment(MOCON Corp.). For comparison. an MgD- and $SiO_2$-based composite film has lower values of WVTR and OTR than inorganic composite/compound films of ones. The results obtained here shows that this film is suitable for passivation layer to extend the life-time of OLEDs.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.284-289
• /
• 2005

According to the nuclear safety regulation policy including the administration of radionuclides in low level radwastes, the evaporator bottoms were mixed with cement to form a stable solidification for identifying the recovery possibility of the C-14. The chemical oxidation method was applied for the extraction of C-14 from the cement waste form. The emitting beta ray of the C-14 extracted from the radwastes was measured with the liquid scintillation counter and calculated by using the quenching correction curves. Only the beta emitting radioactive nuclides of the C-14 in the radwastes was showed the radioactivities with the range of $2.7E+00\;{\sim}\;3.07E+02$ Bq/g.

• Journal of the Korean Solar Energy Society
• /
• v.25 no.4
• /
• pp.37-44
• /
• 2005

An experimental study was conducted to analyze performance of a heating system with variation of control logic of the system. The system uses a solar as heat source and composed with heat pump that uses R-22 as working fluid. The difference between the developed system and the commercially available heating system is working fluid. The solar assisted heating system which was widely distributed in the market uses water as a working fluid. It could be freezing in case of the temperature drops down under freezing point. The anti-freezing fluids such as methyl-alcohol or ethylene-glycol are mixed with the water to protect the freezing phenomena. However, the system developed in this study uses a refrigerant as a working fluid. It makes the system to run under zero degree temperature conditions. Another difference of the developed system compare with commercial available one is auxiliary heating method. The developed system has removed an auxiliary electric heater that has been used in conventional solar assisted heating system. Instead of the auxiliary electric heater, an air source heat exchanger which generally used as an evaporator of a heat pump was adapted as a backup heating device of the developed system. As results, an efficiency of the developed system is higher than a solar assisted heat pump with auxiliary electric heater. The merit of the developed system is on the performance increment when the system operates at a lower solar energy climate conditions. In case of the developed system operates at a normal condition, COP of the solar collector driven heat pump is higher than the air source heat exchanger driven heat pump's.

• Journal of Information Display
• /
• v.7 no.3
• /
• pp.13-18
• /
• 2006

Currently, the flexible organic light emitting devices (OLEDs) are investigated. They are very vulnerable to moisture, and thus have been found to show some problems. Thus, an effective barrier layer is needed to protect from moisture in air. We deposited thin films with magnesium oxide (MgO) and silicon oxide $(SiO_{2})$ compounds mixed at various mixture ratios on flexible polyether sulfone (PES) substrates by an electron-beam evaporator to investigate their applizability for transparent barrier applications. In this study, we found that as the MgO fraction increased, thin films comprised of MgO and $(SiO_{2})$ compounds became more amorphous and their surface morphologies become smoother and denser. In addition, zirconium oxide $(ZrO_{2})$ was added to the above-mentioned compound mixtures. $ZrO_{2}$ made thin mixture films more amorphous and made the surface morphology denser and more uniform. The water vapor transmission rates (WVTRs) of the whole films decreased rapidly. The best WVTR was obtained by depositing thin films of Mg-Si-Zr-O compound among the whole thin films. As the thin mixture films became more amorphous, and the surface morphology become denser and more uniform, the WVTRs decreased. Therefore, the thin mixture films became more suitable for flexible OLED applications as transparent passivation layers against moisture in air.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.4
• /
• pp.235-240
• /
• 1979

A study on the amino acid composition of raw frozen krill, and krill solubles manufactured in forms of paste and powder has been carried out. The raw frozen krill was thawed, chopped, mixed and homogenized with same amount of water. The mixture was autolyzed or hydrolyzed by tile addition of $0.2\%$ pronase-p, a commercial proteolytic enzyme, to the weight of the raw frozen krill at $45^{\circ}C$ for 4 hours. After a thermal inactivation of enzymes at $95^{\circ}C$ for 15 minutes, the autolysate and the hydrolysate were centrifuged and filtered through gauzes, respectively, and then tile lipid layer in the supernatant was removed, The autolysate and the hydrolysate were finally concentrated under reduced atmospheric pressure in a rotary vacuum evaporator at $45^{\circ}C$ for 1 hour to produce the krill solubles in form of paste. The powdered krill solubles were prepared by the addition of $5\%$ starch to the autolysate and hydrolysate and by means of concentration in the rotary vacuum evaporator at $45^{\circ}C$ for 30 minutes and a forced air drying at $58^{\circ}C$ for 3 hours with a air velocity of 3m/sec. Among the amino acids in raw frozen krill, glutamic acid, lysine, and aspartic acid showed high values in quantity and then followed leucine, alanine, arginine, glycine and proline. The qnantity of histidine was very small and that of cystine was only in trace. The krill solubles in forms of paste and powder prepared by autolysis and hydrolysis with pronase-p revealed almost the same patterns in amino acid composition as in raw frozen krill. In case of free amino acids, a large quantity of it in raw frozen krill consisted of lysine, arginine, proline, alanine and leucine. The quantities of cystine, histidine and glutamic acid were, in contrast, very small. In the soluble krill paste prepared by autolysis, lysine, leucine, threonine and alanine existed in large quantities among the free amino acids and cystine, aspartic acid and histidine existed in small quantities. The contents of almost all of the free amino acids ill soluble krill paste perpared by hydrolysis with pronase-p were increased slightly as compared with those in soluble krill paste prepared by autolysis. In this product, the contents of cystine, histidine and serine were very low and lysine, leucine, arginine and proline were the dominant group in quantities among the free amino acids. The krill solubles in forms of paste and powder were not inferior to whole egg in the view point of its essential amino acid composition.

• Journal of the Korean Vacuum Society
• /
• v.9 no.2
• /
• pp.155-161
• /
• 2000

BN films composed of c-BN(70%) and h-BN(30%) phases have been synthesized by the ion beam assisted deposition (IBAD) process and stabilized by post-annealing. Boron was e-beam evaporated at 1.2 $\AA$/sec and nitrogen was ionized and accelerated at about 100 eV by the end-hall type ion gun. Substrates were negatively biased by DC 400 and 500 V, respectively, and heated at $700^{\circ}C$. Synthesized BN films were in-situ post-annealed at 700 or $800^{\circ}C$, respectively, for 1 hr without breaking vacuum. BN films without post-annealing were peeled off from substrates immediately when they were exposed to the air while those with post-annealing at $800^{\circ}C$ were stabilized. Post annealing reduced the film stress from 4.9 GPa to 3.4 GPa, but no considerable stress release in the c-BN phase was observed, contrary to previous reports that the stress relaxation in the c-BN phase is the main mechanism for the stabilization. Structural and chemical relaxation of non c-BN phase is supposed to be responsible for the film stress reduction and, in turn, stabilization, especially when the c-Bn content of the film is not high.

• Analytical Science and Technology
• /
• v.21 no.6
• /
• pp.543-552
• /
• 2008

This paper described the relatively sensitive and simultaneous analytical method for 3-monochloropropane-1,2-diol (3-MCDP, $C_3H_7ClO_2$, MW. 110) as well as 1,3-dichloropropan-2-ol (1,3-DCP, $C_3H_6Cl_2O$, MW. 128) in various foods. Food samples were homogenized in 5M NaCl solution, mixed with aluminum oxide and eluted with dichloromethane. The extracted chloropropanols were concentrated by rotary evaporator and $N_2$ blow serially were derivatized with HFBA (Heptafluorobutyric anhydride, $C_8F_{14}O_3$, MW. 410) and were determined by GC/MS using isotope dilution method. The characteristic molecular ions at m/z 253, 275, 289, 291, and 453 for HFBA derivatives of 3-MCPD (MW. 502) and 110, 275, and 277 for HFBA derivatives of 1,3-DCP (MW. 325) were chosen in selected ion mode. The method validation data showed sufficiently good properties of LOD (0.003 mg/kg), LOQ (0.010 mg/kg), linearity ($R^2{\geq}0.999$ at 0.010~1.000 mg/kg), and recovery rate (${\approx}97%$). The levels of chloropropanols in soy sauce, sauces, processed meat products, fishery products, and seasonings (n=56/157) determined by the presented method were 0.0~0.3 mg/kg.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.6
• /
• pp.449-469
• /
• 2011

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering during 2010. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) Research trends of thermal and fluid engineering have been surveyed as groups of general thermal and fluid flow, fluid machinery, and new and renewable energy. Various topics were presented in the field of general thermal and fluid flow. Research issues mainly focused on the thermal reliability of axial fan and compressor in the field of fluid machinery. Studies on the design of ground source heat pump systems and solar chemical reactors were executed in the field of new and renewable energy. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics and industrial heat exchangers. Researches on heat transfer characteristics included heat transfer in thermoelectric cooling/power generation systems, combined heat and power systems, carbon nano fluid with PVP, channel filled with metal foam and smoke ventilation in a rescue station of a railroad tunnel. Also the studies on flow boiling of R123/oil mixture in a plain tube bundle and R410A charge amount in an air cooled mini-channel condenser were reported. In the area of industrial heat exchangers, researches on plate heat exchanger, shell and tube heat exchanger, enthalpy exchanger, micro channel PCHE were performed. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics and industrial heat exchangers. Researches on heat transfer characteristics included heat transfer in thermoelectric cooling/power generation systems, combined heat and power systems, carbon nano fluid with PVP, channel filled with metal foam and smoke ventilation in a rescue station of a railroad tunnel. Also the studies on flow boiling of R123/oil mixture in a plain tube bundle and R410A charge amount in an air cooled mini-channel condenser were reported. In the area of industrial heat exchangers, researches on plate heat exchanger, shell and tube heat exchanger, enthalpy exchanger, micro channel PCHE were performed. (3) Refrigeration systems with alternative refrigerants such as hydrocarbons, mixed refrigerants, and CO2 were studied. Performance improvement of refrigeration systems are tried applying various ideas of refrigerant subcooling, dual evaporator with hot gas bypass control and feedforward control. The hybrid solar systems combining the solar collection devices with absorption chillers or compression heat pumps are simulated and studied experimentally as well to improve the understanding and the feasibility for actual applications. (4) Research trend in the field of mechanical building facilities has been found to be mainly focused on field applications rather than performance improvements. Various studies on heating and cooling systems, HVAC facilities, indoor air environments and energy resources were carried to improve the maintenance and management of building service equipments. In the field of heating and cooling systems, papers on a transformer cooling system, a combined heat and power, a slab thermal storage and a heat pump were reported. In the field of HVAC facilities, papers on a cooling load, an ondol and a drying were presented. Also, studies on HVAC systems using unutilized indoor air environments and energy resources such as air curtains, bioviolence, cleanrooms, ventilation, district heating, landfill gas were studied. (5) In the field of architectural environment and energy, studies of various purposes were conducted such as indoor environment, building energy, renewable energy and green building. In particular, renewable energy and building energy-related researches have mainly been studied reflecting the global interest. In addition, many researches which related the domestic green building certification of school building were performed to improve the indoor environment of school.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.6
• /
• pp.521-537
• /
• 2012

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2011. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) Research trends of thermal and fluid engineering have been surveyed as groups of fluid machinery and fluid flow, thermodynamic cycle, and new and renewable energy. Various topics were presented in the field of fluid machinery and fluid flow. Research issues mainly focused on the rankine cycle in the field of thermodynamic cycle. In the new and renewable energy area, researches were presented on geothermal energy, fuel cell, biogas, reformer, solar water heating system, and metane hydration. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer, nanofluids and industrial heat exchangers. Researches on heat transfer characteristics included heat transfer above liquid helium surface in a cryostat, methane hydrate formation, heat and mass transfer in a liquid desiccant dehumidifier, thermoelectric air-cooling system, heat transfer in multiple slot impinging jet, and heat transfer enhancement by protrusion-in-dimples. In the area of pool boiling and condensing heat transfer, researches on pool boiling of water in low-fin and turbo-B surfaces, pool boiling of R245a, convective boiling two-phase flow in trapezoidal microchannels, condensing of FC-72 on pin-finned surfaces, and natural circulation vertical evaporator were actively performed. In the area of nanofluids, thermal characteristics of heat pipes using water-based MWCNT nanofluids and the thermal conductivity and viscosity were measured. In the area of industrial heat exchangers, researches on fin-tube heat exchangers for waste gas heat recovery and Chevron type plate heat exchanger were implemented. (3) Refrigeration systems with alternative refrigerants such as $CO_2$, hydrocarbons, and mixed refrigerants were studied. Heating performance improvement of heat pump systems were tried applying supplementary components such as a refrigerant heater or a solar collector. The effects of frost growth were studied on the operation characteristic of refrigeration systems and the energy performance of various defrost methods were evaluated. The current situation of the domestic cold storage facilities was analyzed and the future demand was predicted. (4) In building mechanical system fields, a variety of studies were conducted to achieve effective consumption of heat and maximize efficiency of heat in buildings. Various researches were performed to maximize performance of mechanical devices and optimize the operation of HVAC systems. (5) In the fields of architectural environment and energy, diverse purposes of studies were conducted such as indoor environment, building energy, and renewable energy. In particular, renewable energy and building energy-related researches have mainly been studied as reflecting the global interests. In addition, various researches have been performed for reducing cooling load in a building using spot exhaust air, natural ventilation and energy efficiency systems.