• 한국가스학회지
• /
• 제23권1호
• /
• pp.12-18
• /
• 2019

자동차 엔진이나 소각로 등의 연소기기에서 질소산화물을 저감하기 위한 여러 가지 방법 중에 배기가스 재순환 방법이 널리 쓰이고 있다. 본 연구에서는 고온의 배기가스를 재순환 유입하기 위해 벤튜리 튜브를 사용할 경우에 상온의 공기 노즐 출구 위치를 변화하여 고온의 배기가스를 재순환 유입하는 최적 위치를 도출하기 위해 전산 열유체해석을 통해 살펴보았다. 또한 상온의 공기 노즐 출구에 원뿔을 설치한 경우에 대한 배기가스 재순환 유입량 특성을 고찰하였다. 공기 노즐 출구 위치를 배기가스 재순환 유입 출구의 시작위치(z=0)에서 끝 위치(z=0.6m)로 변화하였을 때 유선과 온도 분포 변화를 관찰하였으며 배기가스 재순환 유입량비와 혼합가스 출구의 평균온도로 정량적으로 비교하였다. 본 연구를 통하여 상온의 공기 노즐 출구 위치는 z=0.15m(1/4L)에서 재순환 유입량과 출구에서의 평균온도가 가장 최대가 되는 것을 알 수 있었다. 또한 공기 노즐 출구에 원뿔을 설치하면 공기 노즐 출구의 속도가 증가하여 배기가스 재순환 유입량이 약 2배 증가하고 혼합가스 출구 온도도 $116^{\circ}C$ 증가하는 것을 알 수 있었다.

• 해양환경안전학회지
• /
• 제19권5호
• /
• pp.518-524
• /
• 2013

본 연구에서는 균질기에 의해 혼합된 물과 벙커-A를 보일러로 연소하였을 때의 배기 배출물 특성에 대해 연구를 수행하였다. 그 결과로 균질기로 균질화 된 벙커-A의 경우, 순수 벙커-A에 비해 NOx 농도는 19 %, CO 농도는 54 % 감소를 나타냈다. 물-벙커A의 경우 물 혼합 비율이 증가할수록 NOx 농도분포가 낮아지는 것을 확인할 수 있었다. 특히, 20 %물-80 %벙커-A의 경우 순수한 벙커-A 보다 배기가스 내 NOx 농도가 45 %까지 감소하였다. 그러나 20 %물-80 %벙커-A의 경우, CO농도 분포는 불규칙한 변화를 나타냈다. 이것은 일정량 이상의 물 혼합은 보일러의 연소 성능 저하 원인이 될 수 있다는 것을 의미한다. 이 결과로부터 본 연구에서 보일러의 정상 연소를 위한벙커A유 내 물의 한계 혼합율은 15 % 인 것을 알 수 있었다. 연돌 부근에서 채취한 매연 부착양은 물의 혼합율이 증가할수록 감소하였다.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.49-61
• /
• 1983

U shape multitube heat exchanger was equipped in the flue to recover the exhaust heat from the boiler system. The fluids of the exhaust heat recovery equipment were the flue gas as the hot fluid, and the water as the cold fluid. The flow geometry of the fluids was cross flow - two pass, the hot fluid being mixed and the cold fluid unmixed. The results of the theoretical and the experimental analysis and the economic evaluation are summarized as follows. 1) The heat exchanger effectiveness and the temperature efficiency of the hot fluid were about 35% when the fuel consumption rate was 140 - 150 L/15min. The temperature efficiency for the cold fluid ranged from 3.0% to 4.5%. The insulation efficiency ranged from 85% to 98%, which was better than the KS air preheater insulation efficiency of 90%. 2) The relationship between the fuel consumption rate, F, and the outlet temperature, $T_{h2}$, of the flue gas from the heat exchanger was $T_{h2}$ = 0.927F + 110. In order to prevent the low temperature corrosion from the coagulation of $SO_3$, it is necessary to maintain the fuel consumption rate above 82 L/15min. 3) The ratio of the exhaust heat from the boiler system to the total energy consumption was about 14.5%. With the installation of the exhaust heat recovery equipment, the energy recovery ratio to the exhaust heat was about 25%. Accordingly, about 3.6% of the total fuel consumption was estimated to be saved. 4) Economic analysis indicated that the installation of the exhaust heat recovery equipment was feasible to save the energy, because the capital reocvery period was only 10 months when the fuel consumption rate was 80 L/15min. 4 months when it was 160 L/15min. 5) Based on the theoretical and the experimental analysis, it was estimated to save the energy of about 18 million Won per year, if four heat exchangers are installed in a factory. 6) A further study is recommended to identify the relationship among the flow rate of the exhaust gas, the size of the heat exchanger and the capacity of the air preheater. For a maximum heat recovery from the exhaust gas an automatic control system is required to control the flow rate of the cold fluid depending on the boiler load.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.236-241
• /
• 2009

After analyzing the characteristics of the cooling dryer, the mixed cooling dryer was developed by adding the desiccant dryer which supplement the cooling dryer's demerits. Also, the hybrid desiccant cooling dryer was developed to use effectively the exhaust heat energy of the cooling dryer. It could make a more that 20 percent reduction in energy compared with the mixed desiccant cooling dryer. It has become essential to supply this equipment and search the suitable drying product.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.112-122
• /
• 1995

As an alternative fuel producing less exhaust emissions, natural gas is of interest for use both in SI and CI engines. The potential of natural gas fuelled dual-fuel engine is considered high enough. However, much effort has to be made so that gaseous fuel is used efficiently with simultaneous minimum use of pilot oil. Hence, a simplified three-dimensional model, using a finite volume method in cylindrical coordinates, has been developed to facilitate an understanding of the dual-fuel combustion phenomena and to predict the complex interactions between the pilot distillate and natural gas. The computer model was calibrated by comparing it with the experimental results obtained from diesel engine like combustion bomb tests. In the pre-mixed natural gas combustion, the fuel burning was highly reliant on the injection condition and subsequent burning nature of the pilot distillate.

• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.22-28
• /
• 2005

Exhaust gas emissions from internal combustion engines are one of the major sources of air pollution. And, it is extremely difficult to increase gasoline engine efficiency and to reduce $NO_X$ and PM(particulate matter) simultaneously in diesel combustion. This paper offers some basic concepts to overcome the above problems. To solve the problems, a recommended technique is CAI(controlled auto-ignition) combustion. In this paper, a flame trap was used to simulate internal EGR(exhaust gas recirculation) effect. An experimental study was carried out to find combustion characteristics using homogeneous premixed gas mixture in the constant volume combustion chamber(CVCC). Flame propagation photos and pressure signals were acquired to verify the flame trap effect. The flame trap creates high speed burned gas jet. It achieves higher flame propagation speed and more stable combustion due to the effect of geometry and burned gas jet.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.491-494
• /
• 2008

The hydrogen fuel and fuel cell which have high energy efficiency and low pollutant emission are getting interest as an alternative energies due to the fossil fuel exhaust, green house effect and atmospheric pollutant problems. The hydrogen gas is very effective as an alternative energy. But, if it is leaked into the air it forms the mixed gas with the air then the danger of the explosion is risen up. So, the secure the safety is mostly important. In this research, to detect the leakage of the hydrogen rapidly, added the odorant materials which don't include the sulfur component into the hydrogen gas and researched on the effect of each odorant on the performance of the fuel cell. As the results, setting the cumulation electric power on the basis and comparing the pure hydrogen, 2,3-Butanedione 5ppm mixed gas 86.1%, 5-Ethylidene-2-Norbornene 17ppm mixed gas 88.2%, Isovaleraldehyde 10ppm mixed gas 74.8%, Ethyl Isobutyrate 2.2ppm mixed gas 93.5% of performance was shown.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.84-92
• /
• 2002

On the cold start of LPG engine, as the engine temperature has not reached its equilibrium temperature, liquid LPG could not be changed perfectly gaseous LPG, although it was passed to the vaporizer. Liquid and gas mixed fuel could influence starting ability and exhaust emission characteristics of LPG engine. In this study, the vaporization characteristic of liquid LPG was investigated with a conventional vaporizer and the vaporizer with heat source(glow plug) installed at preheated chamber inlet, by using the visualization methods and engine test. According to visualization result, even if the engine coolant temperature was $14^{\circ}C$, liquid fuel was supplied to primary chamber over 25 seconds without vaporizing from preheated chamber in such a conventional vaporizer. However, the vaporizer with heat source do not correspond with that, scarcely had been trim on glow plug when LPG began to vaporize. The effectiveness of heat source could be verified by application to the conventional LPG engine.

• Journal of Biosystems Engineering
• /
• 제32권5호
• /
• pp.279-283
• /
• 2007

In this study, the potential possibility of oxygenates on di-ether group (DBE, dibutyl ether) was investigated as an additives for an agricultural direct injection diesel engine. It tested to estimate change of engine performance and exhaust emission characteristics for the commercial diesel fuel and oxygenates additives blending fuel which has four kinds of mixed ratio. The smoke emission of blending fuel (diesel fuel 80 vol-% + DBE 20 vol-%) was reduced in comparison with diesel fuel, that is, it was reduced approximately 26% at 2500 rpm, full load. And, power, torque and brake specific energy consumption didn't have large differences. But, NOx emission of blended fuel was increased compared with commercial diesel fuel.

• ETRI Journal
• /
• 제28권6호
• /
• pp.777-786
• /
• 2006

Since the introduction of competition in the telecommunication market due to the growth of the interconnection between heterogeneous networks, particularly fixed and mobile networks, the interconnection charge based on traffic-sensitive (TS) and non-traffic-sensitive (NTS) costs has become more important. Although there have been many studies of the public switched telephone network (PSTN), previous studies of TS and NTS costs in mobile networks are very few. In this paper, as a pilot study, we propose three criteria and a procedure for the classification of TS and NTS costs based on mobile systems. The three criteria are the following: function type, investment requirement, and main exhaust driver. Moreover, for a CDMA mobile system, strongly TS, strongly NTS, and mixed components are classified by the proposed criteria and procedure. The proposed criteria, procedure, and classification can provide a systematic and useful guideline to decide the scope of mobile facilities and to determine the terminating cost on mobile networks from fixed networks.