• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.133-134
• /
• 2002

The use of low friction wear resistant coatings for machine components is rapidly increasing. These components may operate in any lubrication regime, and less frequently even unlubricated. When run unlubricated it is easy to see the beneficial effect of a low friction coating. However, it has frequently been shown that the coating may also be very beneficial under boundary and mixed lubrication conditions. The present digest briefly presents a few interesting aspects of the use of low friction coatings in lubricated contact illustrated by selected experimental results.

• Tribology and Lubricants
• /
• v.31 no.6
• /
• pp.245-250
• /
• 2015

This study investigates the lubrication characteristics of fuel injection pumps with reference to different fuel oils. Medium-speed diesel engines use fuel oils with various viscosities, such as heavy fuel oil (HFO, which is a high-viscosity fuel oil) and light diesel oil (LDO, which is a low-viscosity fuel oil). When fuel oil with a low viscosity is used, both fuel oil and lubricating oil lubricate the system. Thus, the lubrication of the fuel injection pump is in a multi-viscosity condition when the fuel oil in use changes. We suggest three cases of multi-viscosity models, and divide the fuel injection pump into three lubrication sections: a, the new oil section; b, the mixed oil section; and c, the used oil section. This study compares the lubrication characteristics with variation of the multi-viscosity model, clearance. The volume of Section b does not affect the lubrication characteristics. The lubrication characteristics of the fuel injection pump are poor when high-viscosity fuel oil transfers to low-viscosity fuel oil. This occurs because the viscosity in the new oil section (i.e., Section a) dominates the lubrication characteristics of the fuel injection pump. However, the lubricant oil supply in the used oil section (i.e., Section c) can improve the lubrication characteristics in this condition. Moreover, the clearances of the stem and head significantly influence the lubrication characteristics when the fuel oil changes.

• Tribology and Lubricants
• /
• v.37 no.1
• /
• pp.25-30
• /
• 2021

The surface texture produced via surface texturing is an important approach for controlling the tribological behavior of friction behavior of mechanical devices. The purpose of this study is to investigate the effect of grooves generated via ultrasonic nanocrystal surface modification (UNSM) technology on the tribological performance of AISI 4150 steel against stainless steel 316L. In the study, tribological tests are performed under two different regimes, namely mixed and hydrodynamic lubrication, by varying the applied normal load and reciprocating speed during the tests. According to the test results, the friction coefficient decreases as static load (10 N, 30 N, and 50 N) of UNSM technology increases in the mixed lubrication regime. Conversely, the friction coefficient increases as the static load (10 N, 30 N, and 50 N) of UNSM technology increases in the hydrodynamic lubrication regime. Hence, the results indicate that micro-grooves generate hydrodynamic pressure in the outlet, which increases the oil film thickness between the two mating surfaces. This potentially leads to a reduction in friction in the mixed lubrication regime due to the prevention of contact of asperities and debris. However, the results indicate an adverse effect in the hydrodynamic lubrication regime. In this regard, additional experiments should be performed to investigate the effect of grooves generated by UNSM technology at varying conditions on the friction behavior of AISI 4150 steel, which in turn can be controlled by the generated pressure and oil film thickness at the contact interface.

• Tribology and Lubricants
• /
• v.29 no.1
• /
• pp.27-32
• /
• 2013

This study examined the effects of surface roughness in the mixed lubrication regime of smooth and rough surfaces for roller bearings. The average flow model was adopted for interaction between the flow rheology of the lubricant and the surface roughness. The average Reynolds equation and related flow factor that describes the coupled effects of surface roughness and flow rheology, the viscosity-pressure and density-pressure equations, the elastic deformation equation, and the force balance equation were solved simultaneously. The results showed that the effects of surface roughness on the film thickness and pressure distribution should be considered, especially in elastohydrodynamic lubrication contact problems.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.280-288
• /
• 2000

In this study, flow factors are evaluated in terms of kurtosis using random rough surface generated numerically. As h/$\sigma$become large øx, øy, øfp approach to 1 and øs, øfs to 0 asymptotically regardless of kurtosis. øx, øy, øfp increase with increasing kurtosis in the mixed lubrication regime. øs, øfs is associated with an additional flow transport due to the combined effect of sliding and roughness. As h/$\sigma$ decreases øs, øfs increase up to a certain point, and then decrease toward zero. This behavior can be attributed to the increasing number of contacts in the mixed lubrication regime. øx in the presence of elastic deformation on the surface is larger than øx in the absence of it because local film thickness( h$\_$T/) increases by elastic deformation.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.58-64
• /
• 2005

An OEM driven working group started in January 2004 to elaborate the philosophies, concepts and test procedures for testing piston ring and cylinder liner materials as well as engine oils outside the engine using the $SRV^{(R)}$ test equipment. The different $SRV^{(R)}$ test philosophies in use by OEMs are compiled. The working group focuses on a.) ASTM sequence VIB (Fuel economy by aging oils), b.) friction and wear in the top dead region under mixed/boundary lubrication, c.) extreme pressure load under mixed/boundary lubrication and d.) hydrodynamic friction. Tribological test result and precision data are presented.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.30-37
• /
• 1998

It is well known that reduction of friction loss due to the valve train system greatly affects on improvement of fuel economy in internal combustion engine. In order to investigate friction characteristics of valve train system we carried out friction force measurement using test rig developed by ourselves. From test results, we concluded that characteristics of lubrication and friction torque on the valve train system such as mixed and hydrodynamic was mainly governed the contact type between cam and tappet.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1991.06a
• /
• pp.1-30
• /
• 1991

The lubrication state between contacting bodies with rolling and sliding under loaded condition is generally understood by the conception shown in Figure 1. When the lubricating oil film formation between facing bodies is good enough to separate these bodies by the hydrodynamic pressure, this state is called by the expression of "hydrodynamic lubrication". The thickness of oil film is so large that the lubricating oil between facing bodies behaves as fluid and metal-to-metal contact between surface roughness asperities on facing bodies does not occur. When the oil film thickness becomes thinner or when the surface roughness height becomes larger, top of surface roughness asperities on facing bodies reaches very near to each other and there the oil or absorbed oil molecules on the surface of facing bodies behave no more as fluid. Partly metal-to-metal contact of surface roughness asperities occurs. Such lubrication state is called by the expression "mixed-lubrication". When the oil film thickness becomes more thinner or surface roughness height becomes larger, metal-tometal contact or contact via absorbed oil molecules dominate at most of the part in contact zone. Such state is called by the expression "boundary lubrication". Schematic representation of these three regimes of lubrication is shown in Figure 1.rication is shown in Figure 1.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.17-24
• /
• 2004

Surrface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern using photolithography on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions from based on friction map. Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.