• 제목/요약/키워드: Misorientation

검색결과 59건 처리시간 0.025초

액상확산접합한 Ni기 단결정 초내열합금의 고온인장특성 (High Temperature Tensile Property of Transient Liquid Bonded Joints of Ni-base Single Crystal Superalloy)

  • 김대업;강정윤
    • Journal of Welding and Joining
    • /
    • 제18권3호
    • /
    • pp.106-113
    • /
    • 2000
  • Single crystallization behavior ad high temperature tensile properties of TLP bonded joints of Ni-base single crystal superalloy, CMSX-2 were investigated using MBF-80 and F-24 insert metals. CMSX-2 was bonded at 1523~1548K for 1.5~1.8ks in vacuum. The (100) orientation of bonded specimen was aligned perpendicular to the joint interface. Crystallographic orientation analyzed points over the bonded region possessed the almost same orientation across the joint interface and misorientation $\Delta^{\theta}$ was negligibly small in as-bonded and post-bond heat-treated situations. It was confirmed that single crystallization could be readily achieved during TLP bonding. The tensile strengths of all joints at elevated temperatures were equal to or greater than those of base metal the range of testing temperature between 923K and 1173K. The elongation and reduction of area in values were almost the same as those of base metal. SEM observation of the fracture surfaces of joints after tensile test revealed that the fracture surface indicated the similar morphologies each other, and that the fracture of joints occurred in the base metal in any cases.

  • PDF

비자기 차폐환경에서 미세자기신호 측정을 위한 고온 초전도 SQUID 자력계의 설계 및 제작 (Designs and Fabrications of High-TC SQUID Magnetometer for Measuring a Weak Signal without Magnetic Shielding)

  • 유권규;김인선;박용기
    • 센서학회지
    • /
    • 제13권2호
    • /
    • pp.110-113
    • /
    • 2004
  • We have designed and fabricated the YBCO single layer directly-coupled SQUID magnetometers for the purpose of magnetocardiography in a magnetically disturbed environment. The SQUID magnetometers were designed three different types of pickup coil such as solid type, PL type I and PL type II for further stable fluxed-locked-loop operation without magnetic shielding. Magnetometer was fabricated with a single layer YBCO thin film deposited on STO(100) bicrystal substrate with misorientation angle of $30^{\circ}$. We have achieved a magnetic field noise BN of 30 fT/$Hz^{1/2}$ at 100 Hz, and less than 70 fT/$Hz^{1/2}$ at 1 Hz. The PL type II SQUIDs have exhibited the most stable fluxed-locked-loop operation in a magnetically unshielded environment.

Microstructure and Trapped Magnetic Field of Multi-Seeded Single Domain YBCO

  • Bierlich, J.;Habisreuther, T.;Litzkendorf, D.;Zeisberger, M.;Gawalek, W.
    • Progress in Superconductivity
    • /
    • 제8권1호
    • /
    • pp.8-15
    • /
    • 2006
  • The size of the superconducting domains and the critical current density inside these domains have to be enhanced for most of cryomagnetic applications of melt-textured YBCO bulks. To enlarge the size of the domains we studied the multi-seeding technique based on a well-established procedure for preparing high quality YBCO monoliths using self-made SmBCO seeds. The distance between the seeds was optimised as a result of the investigation of the effects of various seed distances on the characteristics of the grain boundary Junctions. The influences of a-b plane intersections and c-axis misalignments were researched. Thereby, a small range of tolerance of the misorientations between the seed crystals was found. Field mapping was applied to control the materials quality and the superconductor's grain structure was investigated using polarisation microscopy. YBCO function elements with iou. seeds in a line and an arrangement of making type (100)/(100) and (110)/(110) boundary junctions, respectively, were processed. The trapped field profile in both sample types shows single domain behaviour. To demonstrate the potential of the multi-seeding method a ring-shaped sample was processed by placing sixteen seeds in a way to make both (100)/(100) and (110)/(110) grain junctions at the same time. The results up to now are very promising to prepare large single domain melt-textured YBCO semi-finished products in complex shapes.

  • PDF

고분해능 XRD를 이용한 LED용 대구경 사파이어 단결정 웨이퍼의 면방위 결정

  • 빈석민;유병윤;전현구;오병성;김창수
    • 한국진공학회:학술대회논문집
    • /
    • 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
    • /
    • pp.361-361
    • /
    • 2012
  • 사파이어 단결정은 LED 소자의 기판으로 널리 사용되고 있으며 현재 소자 수율을 향상시키기 위하여 6인치 이상의 대구경 웨이퍼를 만들기 위한 많은 노력을 경주하고 있다. 단결정, 특히 반도체 단결정 웨이퍼에서 ($00{\cdot}1$), ($10{\cdot}2$) 등의 어떠한 결정학적인 방위(crystallographic orientation)가 표면과 이루는 각도, 즉 표면방위각(off-cut 또는 misorientation angle)의 크기와 방향은 제조된 LED 소자의 물성에 영향을 끼치므로 웨이퍼를 가공할 때 정확하게 콘트롤해야 한다. 본 연구에서는 고분해능 X-선을 이용하여 표면이결정학적 방향과 이루는 면방위각을 정밀하게 결정하는 측정법을 연구하였다. 기존의 ASTM 의 측정법과는 다른 원리를 이용하고 웨이퍼의 휨(bending)이나 측정고니오 회전축의 편심과 무관하게 표면방위각을 결정하는 새로운 이론적 모델을 제시하고 그 모델을 적용하여 표면의 수직축이 대구경 사파이어 ($00{\cdot}1$) 축과 이루는 표면방위각을 정확하게 측정 분석하였다. 본 연구에서 사용한 6인치 사파이어 웨이퍼에 대하여 표면방위각은 $0.21^{\circ}$이었으며 표면각이 나타나는 방향은 웨이퍼의 primary edge 방향으로부터 $-1.2^{\circ}$ 벗어나 있는 방향이었다.

  • PDF

Al-6.2wt.%Si 합금의 등온교반시간에 따른 미세조직변화 (Microstructural evolution of rheocast Al-6.2wt.%Si alloy with isothermal stirring)

  • 이정일;박지호;김긍호;이호인
    • 한국주조공학회지
    • /
    • 제15권5호
    • /
    • pp.514-522
    • /
    • 1995
  • The microstructural evolution with isothermal stirring during semi-solid state processing of hypoeutectic Al-6.2wt%Si alloy was studied. Substructure of the individual primary solid particle in the slurry was investigated through transmission electron microscopy(TEM). Formation of subgrain boundaries on the rheocast Al-6.2wt%Si alloy is observed and the misorientation between the grains is shown typically under 2 degrees by analyzing selected area diffraction (SAD) and convergent beam electron diffraction (CBED) patterns. The existence of high angle grain boundaries are also observed in the alloy. Based upon these observations, mechanisms for the primary particles fragmentation are considered. With isothermal stirring, the dislocation density increases, and the evolution of dislocation cell structure takes place, which is interpreted as a process of achieving uniform deformation by dynamic recovery under applied shear stress.

  • PDF

22Cr 린 듀플렉스 스테인리스강의 공식저항성에 미치는 Mn과 Ni 첨가의 영향 (Effect of Alloying Elements of Mn and Ni on the Pitting Corrosion Resistance of 22Cr Lean Duplex Stainless Steel)

  • 안용식;배근국
    • 동력기계공학회지
    • /
    • 제16권5호
    • /
    • pp.76-82
    • /
    • 2012
  • Duplex stainless steels have the dual microstructure of austenite and ferrite phases. This steel exhibits generally a high corrosion resistance and higher mechanical strength compared with austenitic stainless steels. The steels used in the investigation have the chemical composition of Fe-22Cr-xNi-yMn-0.2N in which the contents of Ni and Mn were varied with maintaining the equal [Ni/Cr] equivalent. The fraction of ferrite phase was increased with the increase of annealing temperature. The impact factor of Mn element on the [Ni] equivalent was amended on the basis of the results of the investigation. 4Mn-2Ni alloy showed the highest pitting corrosion resistance. The fraction ratio, grain size and misorientation angle between grains were measured, and the correlation with pitting potential was investigated.

ARB법에 의한 Cu-Fe-P합금의 초미세결정립 형성 (Formation of Ultrafine Grains in Cu-Fe-P Alloy by Accumulative Roll-Bonding Process)

  • 이성희;한승전;김형욱;임차용
    • 한국재료학회지
    • /
    • 제19권8호
    • /
    • pp.432-436
    • /
    • 2009
  • A Cu-Fe-P copper alloy was processed by accumulative roll-bonding (ARB) for ultra grain refinement and high strengthening. Two 1mm thick copper sheets, 30 mm wide and 300 mm long, were first degreased and wire-brushed for sound bonding. The sheets were then stacked on top of each other and roll-bonded by about 50% reduction rolling without lubrication at ambient temperature. The bonded sheet was then cut into two pieces of the same dimensions and the same procedure was repeated for the sheets up to eight cycles. Microstructural evolution of the copper alloy with the number of the ARB cycles was investigated by optical microscopy (OM), transmission electron microscopy(TEM), and electron back scatter diffraction(EBSD). The grain size decreased gradually with the number of ARB cycles, and was reduced to 290 nm after eight cycles. The boundaries above 60% of ultrafine grains formed exhibited high angle boundaries above 15 degrees. In addition, the average misorientation angle of ultrafine grains was 30 degrees.

Study of the Microstructural Evolution of Tempered Martensite Ferritic Steel T91 upon Ultrasonic Nanocrystalline Surface Modification

  • He, Yinsheng;Yang, Cheol-Woong;Lee, Je-Hyun;Shin, Keesam
    • Applied Microscopy
    • /
    • 제45권3호
    • /
    • pp.170-176
    • /
    • 2015
  • In this work, various electron microscopy and analysis techniques were used to investigate the microstructural evolution of a 9% Cr tempered martensite ferritic (TMF) steel T91 upon ultrasonic nanocrystalline surface modification (UNSM) treatment. The micro-dimpled surface was analyzed by scanning electron microscopy. The characteristics of plastic deformation and gradient microstructure of the UNSM treated specimens were clearly revealed by crystal orientation mapping of electron backscatter diffraction (EBSD), with flexible use of the inverse pole figure, image quality, and grain boundary misorientation images. Transmission electron microscope (TEM) observation of the specimens at different depths showed the formation of dislocations, dense dislocation walls, subgrains, and grains in the lower, middle, upper, and top layers of the treated specimens. Refinement of the $M_{23}C_6$ precipitates was also observed, the size and the number density of which were found to decrease as depth from the top surface decreased. The complex microstructure and microstructural evolution of the TMF steel samples upon the UNSM treatment were well-characterized by combined use of EBSD and TEM techniques.

Radiation induced grain boundary segregation in ferritic/martensitic steels

  • Xia, L.D.;Ji, Y.Z.;Liu, W.B.;Chen, H.;Yang, Z.G.;Zhang, C.;Chen, L.Q.
    • Nuclear Engineering and Technology
    • /
    • 제52권1호
    • /
    • pp.148-154
    • /
    • 2020
  • The radiation induced segregation of Cr at grain boundaries (GBs) in Ferritic/Martensitic steels was modeled assuming vacancy and interstitialcy diffusion mechanisms. In particular, the dependence of segregation on temperature and grain boundary misorientation angle was analyzed. It is found that Cr enriches at grain boundaries at low temperatures primarily through the interstitialcy mechanism while depletes at high temperatures predominantly through the vacancy mechanism. There is a crossover from Cr enrichment to depletion at an intermediate temperature where the Cr:Fe vacancy and interstitialcy diffusion coefficient ratios intersect. The bell-shape Cr enrichment response is attributed to the decreasing void sinks inside the grains as temperature rises. It is also shown that low angle grain boundaries (LAGBs) and special Σ coincidence-site lattice (CSL) grain boundaries exhibit suppressed radiation induced segregation (RIS) response while high angle grain boundaries (HAGBs) have high RIS segregation. This different behavior is attributed to the variations in dislocation density at different grain boundaries.

AZ80 마그네슘 합금 압출재의 압축 성형조건에 따른 방위특성 분석 (Texture Evolution of Extruded AZ80 Mg Alloy under Various Compressive Forming Conditions)

  • 윤종헌;이상익;이정환;박성혁;조재형
    • 소성∙가공
    • /
    • 제21권4호
    • /
    • pp.240-245
    • /
    • 2012
  • With the increasing demand for light-weight materials to reduce fuel consumption, the automobile industry has extensively studied magnesium alloys which are light weight metals. The intrinsic poor formability and poor ductility at ambient temperature due to the hexagonal close-packed (HCP) crystal structure and the associated insufficient number of independent slip systems restricts the practical usage of these alloys. Hot working of magnesium alloys using a forging or extrusion enables net-shape manufacturing with enhanced formability and ductility since there are several operative non-basal slip systems in addition to basal slip plane, which increases the workability. In this research, the thermomechanical properties of AZ80 Mg alloy were obtained by compression testing at the various temperatures and strain rates. Optical microscopy and EBSD were used to study the microstructural behavior such as misorientation distribution and dynamic recrystallization. The results were correlated to the hardening and the softening of the alloy. The experimental data in conjunction with a physical explanation provide the optimal conditions for net-shape forging under hot or warm temperatures through control of the grain refinement and the working conditions.