• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권6호
• /
• pp.299-306
• /
• 2000

The primary cause of air pollution by vehicles is imperfect combustion of fuel. One of the most usual causes of this imperfect combustion is the misfire in IC(Intenal Combustion) engine. Recently it is obligated for an ECU to monitor the emission level and warn the driver in case of exceeding specified emission standards. Therefore, in order to comply with this OBD-II regulations, car makers are investing a considerable amount into technology which would enable the detection of misfire and the particular cylinder in which misfire is taking place. So far, it has been able to detect misfire using engine speed, which can be obtained crank angle. However, such a method posed a problem in analyzing at high speed and in recognizing the misfire from the load impact at bumpy road. In this paper, misfire detection is made possible by simple arithmetic using WDFT, especially at high engine speed. In addition, the moving window method of a Walsh function is applied to determine the cylinders under misfire in case of multiple misfires. An actual experiment was conducted to prove that WDFT is applicable to effective in computation speed and to same result in misfire detection and cylinder determination at idle, part load and bumpy road conditions.

• International Journal of Automotive Technology
• /
• 제7권5호
• /
• pp.637-644
• /
• 2006

The detection of engine misfire events is one of major concerns in engine control due to its negative effect on air pollution and engine performance. In this paper, a misfire detection system based on crankshaft angular speed fluctuation is developed. Synthetic variable method is adopted for the preprocessing of crankshaft angular speed. This method successfully estimates the work output of each cylinder by finding the effect of combustion energy on the crankshaft rotational speed or acceleration after virtually removing the effect of the internal inertia forces from the measured crankshaft speed signals. The detection system is developed using neural network with the revised synthetic angular acceleration as input which is derived from the preprocessing. Mathematical simulation is carried out for developing and verifying the misfire detection system. Finally, the reliability of the developed system is validated through an experiment.

• 한국자동차공학회논문집
• /
• 제7권6호
• /
• pp.42-48
• /
• 1999

Engine misfire causes of the negative effect on exhaust emission such as HC, CO, and NOX . Moreover, it causes damage to the three-way-catalyst(TWC) system permanently. The crankshaft velocity fluctuation(CVF) method has been applied for the real cars as misfire detection system usually, which utilizes the crank angle sensor input to calculate the variation of the crankshaft rotational speed. But this approach has the limit due to the fact that three could be problem under certain engine condition like as deceleration or high speed condition . Therefore the development of new methods are requested today. This study introduced the new method of misfire detection using breakdown voltage(BDV) characteristics between spark plug electrouds.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.23-31
• /
• 1996

The crankshaft speed fluctuation was measured every crank angle. In order to detect the misfire, the engine and the dynamometer were considered as a single- degree of freedom system. From this modeling, the detection criteria were derived and examined by the engine test. By this method the single misfire or multiple misfires can be detected. Even on the condition of low load and higher speed than 3000rpm, where it was difficult through the other methods, misfire detection was carried out steadily. From this results, the method proposed by this paper proved reasonable.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.210-217
• /
• 1998

This paper describes the method for detection of the misfired cylinder using the pressure fluctuations occurred in the exhaust system on an MPI gasoline engine. If misfire is occurred in the cylinder of the gasoline engine, the power of engine gets lost, the fuel consumption and the exhaust emission are increased and the vibration is caused by unsteady torque. Therefore early detection and correction of misfire play a very important role in the proper performance and the exhaust emission. This paper suggests method of misfire detection which affect engine performance. The method is a comparison of average pressure index during the displacement period. Experimental results showed that the method using the pressure fluctuations in the exhaust system is proven to be effective in the detection of misfire on gasoline engine regardless loads and revolutions of the engine. In addition, this method, using the pressure fluctuations in exhaust system is easier than other methods and is not a need of additional reconstruction of engine.

• 전자공학회논문지T
• /
• 제35T권1호
• /
• pp.67-74
• /
• 1998

자동차 배기가스의 증가요인인 실화발생을 감지하고 실화가 발생하는 기통까지 판별하기 위하여 종래에는 크랭크각속도를 측정하는 방법을 이용하였으나 이 방법은 고속의 회전시 감지가 어려운 문제를 가지고 있다. 이러한 문제를 해결하기 위해서 본 논문은 이산 월쉬-푸리에(Walsh Discrete Fourier Transform; WDFT)를 이용하여 고속의 엔진회전수에서도 실화발생여부를 판단 가능하게 하였고, 월쉬함수의 Moving window방식을 이용하여 다기통 실화발생에 대한 기통판별까지 가능하게 하였다. 이상의 내용을 시스템으로 구현하여 무부하 Idle상태와 운전상태(Drive)에서 시험한 결과도 실화발생여부를 감지하는데 기존의 방법보다 더 효과적임을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.23-31
• /
• 2000

Knock and misfire, kinds of abnormal combustion, are highly undesirable effect on the internal combustion engine. So, it is important to detect these avnormal combuition and control the ignition timing etc. to avoid these mal-effect factors in real engine system. In this study, the system which detects the knock and the misfire using by spark plug is presented. This system is based on the effect of modulation breakdown voltage(BDV) between the spark gaps. The voltage drop between spark plug electrodes, when an electrical breakdown is initiated, depends on the temperature and pressure in combustion chamber. So, we can detect knock and misfire that produce changes in gas temperature and pressure (consequently, its density) using by BDV signal change which carries information about the character of combustion.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.74-80
• /
• 2005

This paper presents a misfire monitoring method by using the weight factor. According to OBD II(On-Board Diagnostics) regulations of the CARB (California Air Resources Board), an ECU (Electronic Control Unit) should detect misfires which occur in the internal combustion engine. A misfire is 1311owe4 by post-oscillations for short duration. Sometimes, the amplitude of oscillations may be as high as misfire and can be falsely detected as another misfire. To prevent this, the software designers do not attempt to detect another misfire for this short duration, during which the post oscillations exist. Because of this, ECU does not detect all the misfires and hence, the unstable state of automobile cannot be detected. If this happens for a long time, automobile may get damaged. To solve these problems, this paper suggests a new algorithm to detect misfire by using weighting factor Weighting factor is a concept to distinguish the misfire with the post oscillation and to improve the detection rate. This value of weighting factor is used for counting the misfire. This paper also shows the result of experiment done on a automobile using this software. The software is implemented using ASCET-SD which is preferred in the design of engine control. This paper's result show the possibility of improving the misfire detection by implementing this algorithm.

• 한국산업융합학회 논문집
• /
• 제4권4호
• /
• pp.371-378
• /
• 2001

This paper proposes a method to detect the misfired cylinder using a new misfire detection index. The new method of misfired cylinder is a comparison of pressure gradient during the blowdown period of exhaust stroke. If a misfire occurs, the engine will he lost some power and consumes the more fuel and the torque will be unsteady. Most of all, the misfire affects a bad influence of the 3-way catalyst and emits unburned hydrocarbon in the air. To prevent these unusual phenomena and eliminate the factor of the environmental pollution, it is important to detect the misfired cylinder. To do the experiment, set up the assist device on the manifold. This assist device is not deformed for conventional exhaust manifold and installed in the end of the exhaust manifold. Experimental results showed that the method using the mean gradient pressure index is proven to be effective in the detection of misfired cylinder on gasoline engine regardless loads and revolutions of the engine.

• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.1-7
• /
• 2003

This paper proposes a method to detect misfired cylinders by the exhaust pressure ascent rate. The misfire is generated by faults of electric system or faults of fuel delivery system. It is one of the abnormal combustions. Therefore, it increases the unburned hydrocarbon and the carbon monoxide and affects a bad influence to the 3-way catalyst. The misfire causes to decrease the power of the engine and increase the consumption of the fuel. Early detection and correction of the misfired cylinders can prevent these unusual phenomena. The misfired cylinders can be detected by the comparison of exhaust pressure ascent rate during each cycle. The exhaust pressure ascent rate is defined as pressure rise per time. Our experimental results showed that the proposed method is effective in the detection of the misfired cylinders on a gasoline engine regardless loads and revolutions of the engine.