• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.63-68
• /
• 2008

This paper describes about the simulation and the experimental results of optical cavity with curved mirror surface and vertical mirror surface to improve the light intensity and efficiency of the optical sensors. When we use the vertical mirror surface, the distribution of light reached to the filter surface of detector shows an elliptical shape. Whereas, the curved mirror surface focuses the light into circular shape. Therefore, due to focusing effects in case of using curved mirror surface, the light intensity per unit area has been improved. Consequently, the output voltage of gas sensor has been expected to increase. Based upon the simulation, the experiment of gas sensor has been conducted with $CO_2$ gas from 0ppm to 2,500 ppm at 250 ppm step and $25^{\circ}C$, 45%R.H. ambient. The output voltage of gas sensor that has a curved mirror surface increases approximately 200 mV than that of vertical mirror surface.

• Journal of the Korean Society of Industry Convergence
• /
• v.10 no.1
• /
• pp.27-32
• /
• 2007

It has been recently reported that the SERS (Surface Enhanced Raman Scattering) effect of the silver mirror substrate made by Tollen's method is much superior to that of other substrates. In this study, the experiments for comparison of surface enhancement of silver sol and silver mirror substrates were done, where we checked the characteristics of silver mirror substrate made by Tollen's method. The surface enhancement of fluorescein was analyzed by silver sol and silver mirror substrates. We observed the SERS spectra of fluorescein. The assignments of the vibrational bands shown in SERS spectra are given based on both literature and the semi-empirical calculations at the PM3 methods. The surface enhancement properties for fluorescein showed that the silver mirror was more superior to sliver sol substrates. Spectra of fluorescein revealed that fluorescein was adsorbed on silver surfaces by a common oxygen atom. According to the 'surface selection rule', the vibrations in the band intensities reflect the adsorption orientation of the molecule on to the surface of SERS substrates. Therefore, we deduced that the adsorption orientation of fluorescein was little tilted perpendicular to the silver surfaces by using of the surface selection rules.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.10
• /
• pp.68-74
• /
• 1997

The surface finishing system using the micro abrasive film was designed and manufactured to make the mirror surface of the cylindrical workpices. An experimental study of srface finishing was carried out to investigate the performance of mirror surface finishing system. The surface roughness value of stainless steel was about 0.2 .approx. 0.25 .mu. m Rmax, 0.02 .approx. 0.04 .mu. m Ra, using abrasive grain size of 12, 9 .mu. m. The surface roughness value of chrome coated workpiece was about 0.07 .approx. 0.11 .mu. m Ra using abrasive grain size 3 .mu. m. In the same condition, the chrome coated workpiece has obtained better surface roughness charateristics than the one of stainless steel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.9-16
• /
• 2013

The comparisons of performance characteristics between the super-mirror face grinding machine using variable air pressure developed in this laboratory to grind precisely the sliding face of a surface hardened workpiece with thermal spray and the conventional one are investigated by measuring the surface roughness and hardness for a SCM440. To process variously workpiece according to shape, size and materials, the rotating and contacting forces of the developed grinding machine can be changed by air pressure. The surface roughness of processed workpiece can be also attained to state of mirror face by grinding precisely the sliding face with changing the rotating speed of diamond wheel. It is possible to be attached to the various machine tools because the super-mirror face grinding machine using variable air pressure is a small size. The grinding efficiency is elevated because it can be worked by two or more grinding machines attached to concurrently a machine tool for the large workpiece. In this study, results show that the cusp height of the super-mirror face grinding machine for the particle size of 100 and $1500No./mm^2$ is lower than that of the conventional one because the vibration is reduced by rotating very fast the diamond wheel with a pressed air and it can be processed by rotating the diamond wheel with a constantly varied air pressure perpendicular to workpiece surface, and that the workpiece in the super-mirror face grinding machine for the particle size of $3000No./mm^2$ can be processed to state of mirror face that is rarely seen by the cusp height. It is also found that the surface hardness of both the conventional and the super-mirror face grinding machines are increased as the particle size of diamond wheel is reduced, and the surface hardness of the super-mirror face grinding machine is HRC 1.1 ~ 1.8 higher than that of the conventional one.

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.90-94
• /
• 2012

This study has been focused on properties of mirror surface grinding technology by ELID(Electrolytic In-process Dressing) for metal matrix ceramic composites using in high precision mirror for optics. The experimental studies have been carried out to get mirror surface by grinding for composites, Al-SiC, Al-graphite and Mg-SiC. Grinding process is carried out with varying abrasive mesh type, depth of cut and feed rate using diamond wheel. The machining result of the surface roughness and condition of ground surface, have been analyzed by use of surface roughness tester and SEM measurement system. ELID grinding technology could be applied successfully for the mirror-surface manufacturing processes in spite of ductility of metal matrix material. As the results of experiments, surface roughness of Al-SiC(45 wt%) has been the most superior in these experimental work-pieces as 0.021 ${\mu}m$ Ra.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.273-278
• /
• 1994

The surface finishing systems using the micro abrasive film were designed and manufactured to make the mirror surface of the cylindrical workpiece. An experimental study of surface finishing was carried out to investigate the performance of mirror surface finishing system. The surface roughness of stainless steel was about Rmax 0.2~0.25 .mu.m, Ra 0.02~0.04 .mu.m in abrasive grain size 12, 9 .mu.m. the surface roughness of chrome coated workpiece was about Rmax 0.07~ 0.11 .mu. m, Ra 0.01 in abrasive grain size 3 .mu. m. Also, to measure the mirror finishing time by mirror surface finishing system, the experiment was carried out on the chrome coated and ground roller of diameter 76mm and length 650mm. The finishing time and surface roughness were 40min and Rmax 0.1~0.13 .mu.m, Ra 0.01 .mu.m.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.1 s.178
• /
• pp.89-96
• /
• 2006

In this study, fabrication of the large area silicon mirror is accomplished by anisotropic wet etching using micromachining technology for implementation of integrated slim optical pickup and the process condition is also established for improving the mirror surface roughness. Until now, few results have been reported about the production of highly stepped $9.74^{\circ}$ off-axis-cut silicon wafers using wet etching. In addition rough surface of the mirror is achieved in case of tong etching time. Hence a novel method called magnetorheolocal finishing is applied to enhance the surface quality of the mirror plane. Finally, areal peak to valley surface roughness of mirror plane is reduced about 100nm in large area of $mm^2$ and it is applicable to optical pickup using infrared wavelength.

• Journal of the Korean Society of Industry Convergence
• /
• v.15 no.2
• /
• pp.43-47
• /
• 2012

In this study, the experiments for surface enhancement of silver mirror substrate were done, where we checked the characteristics of silver mirror substrate made by Tollen's method. The surface enhancement of Bromothymol blue was analyzed by three kind of silver mirror substrates. The assignments of the vibrational bands shown in SERS spectra are given based on both literature and the semi-empirical calculations at the PM3 methods. Finally, we deduced that the adsorption orientation of bromothymol blue was little tilted flat to the silver mirror surfaces by using of the surface selection rules.

• Journal of the Korean Society of Industry Convergence
• /
• v.14 no.1
• /
• pp.23-27
• /
• 2011

In this study, the experiments for surface enhancement of silver mirror substrates were done, where we checked the characteristics of silver mirror substrate made by Tollen's method. The surface enhancement of Eriochrome Black T(EBT) was analyzed by silver mirror substrates. We observed the SERS spectra of EBT. The assignments of the vibrational bands shown in SERS spectra are given based on both literature and the semi-empirical calculations at the PM3 methods. Finally, we deduced that the adsorption orientation of EBT was little tilted perpendicular to the silver mirror surfaces by using of the surface selection rules.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.119-124
• /
• 2000

In this paper based on geometric optics and geometric modeling aspheric surface of the side mirror mold with dead angle reduced have been designed and machined in a CNC machining center, Surface roughness of the mold was evaluat-ed by usin the surface shaping system. Surface generating simulation of a ball endmill process is investigated. Through the simulation based on the surface-shaping system 3-D engineered surfaces and properties of engineered surfaces are obtained, Computer simulation provides the effective working conditions through the prediction of geometric properties of engineered surfaces. The rear view mirror and room mirror play important role on the safe driving condition as a observation of environment but the rear view mirror can not provide complete information of driving environments due to the existence of the dead angle. The analysis on the shape of formed mirror shows that the proposed me？ improves range of a driver's sight.