• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.793-797
• /
• 2000

The environmental problems by using coolant demanded the new cooling methods. As one of them the studies on the dry grinding with compressed cold air have been done. The cooling method using compressed cold air was effdve thmugh going down the temperature of compressed air supplied below $-25^{\circ}C$ and inneasing the amount of mmpresd cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using MQL(Minimum Quantity Lubrication) or mist newly were suggested. These two methods can satisfy both cooling effect and lubrication with only small amount of coolant, also has the benefit in the point of decreasing the envimnmental pollution. This paper focused on analyzing the grindmg characteristics of the cooling method using mid. The generated heat and grinding force of the cooling method using mist were compared with them of coolant and compressed cold air. And them grinding test according to the temperature of compressed cold air, mist spray amount and mist supply direction were done.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.308-311
• /
• 2004

In this paper, we investigated $\phi-q-n$ distribution to inquire discharge characteristic according to variation of electrode. Also, we investigated Weible distribution of discharge number using Weible analysis to search the relationship between a part discharge and shape of electrode. We increased voltage 1[kV] AC 60[Hz] of impressed voltage, data is acquired a generating discharge for 10 seconds after impressing voltage. Also, as we repeated the experiment 10 times at same condition, analyzed foible using data except for maximum and minimum. As the result, we confirmed that discharge generating and discharge quantity were significantly increased narrowing radius of electrode, also discharge frequency was close to shape of a standard distribution.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.495-496
• /
• 2008

The magnetic characteristics of Mg-Zn ferrite that was fired at $1150^{\circ}C$ for 1hour and sintered at $1250^{\circ}C$ for 3hours was examined. The composition ratio of the ferrite was changed after sintering. In that case the composition ratio of ${Fe_2}{O_3}$ was increased but that of CuO was decreased. When the addition quantity of CuO was 3.8 mole%, it's shrinkage rate had maximum value. Magnetic permeability was decreased as the addition rate of CuO was increased and MgO was decreased. When the composition rate of CuO was 2.3 mol% and MgO was 10.9 mol%, the firing density had maximum value. In case that CuO was 2.8mol% and MgO was 10.4mol%, PL had minimum value.

• 한국기계가공학회지
• /
• 제15권6호
• /
• pp.77-82
• /
• 2016

When drilling through Inconel 601 nickel-chromium-based alloys, a large amount of cutting oil is required to prevent tools from wear and fracturing due to heat buildup resulting from the high temperature resistance and toughness of this alloy. However, cutting oil supply has become a factor compromising the machining environment, and this has caused attention to shift to a more environmentally friendly cutting fluid supply system called minimum quantity lubrication (MQL). Our aim in this study was to find a more efficient drill processing method using MQL, and to verify its performance. To that end, we proposed a sealed cover, a step feed, and POSS-type cutting oil as measures to increase the effectiveness of MQL in view of the cutting force and tool wear, and established an improvement in efficiency using the proposed measures.

• Corrosion Science and Technology
• /
• 제11권5호
• /
• pp.173-178
• /
• 2012

To manage the wall thinning of carbon steel piping in nuclear power plants, the utility of Korea has performed thickness inspection for some quantity of pipe components during refueling outages and determined whether repair or replacement after evaluating UT (Ultrasonic Test) data. When the existing UT data evaluation methods, such as Band, Blanket, PTP (Point to Point) Methods, are applied to a certain pipe component, unnecessary re-inspecting situations may be generated even though the component does not thinned. In those cases, economical loss caused by repeated inspection and problems of maintaining the pipe integrity followed by decreasing of newly inspected components may be generated. EPRI (Electric Power Research Institute) in USA has suggested several statistical methods, TPM (Total Point Method), LSS (Least Square Slope) Method, etc. to distinguish whether multiple inspecting components have thinned or not. This paper presents the analysis results for multiple inspecting components over three times based on both NAM (Near Area of Minimum) Method developed by KEPCO-E&C and the other methods suggested by EPRI.

• 에너지공학
• /
• 제12권2호
• /
• pp.131-138
• /
• 2003

본 연구에서는 평판 경계층의 천이 영역에서 평균속도, 표면마찰계수, 간헐도 분포, 에너지 스펙트럼 등의 신뢰성 있는 실험 자료를 획득하였다. 실험 결과 천이가 진행됨에 따라 난류반점이 지배하는 영역이 벽면 근처에서 전 경계층으로 확산되었으며 이러한 현상의 결과로 속도 섭동량에서 비등방성이 크게 나타난다. 천이 이전영역에서는 에너지가 주로 저주파에 집중되어 있다가 천이를 거치면서 에너지가 고주파 성분으로 이동하였다 이는 두 가지 이상의 에너지 발생과 소멸 메커니즘이 천이영역에서 공존하고 있음을 의미한다. 따라서 천이영역에서의 유동장을 예측하기 위한 난류 계산 모형에서 비등방성과 서로 다른 메커니즘을 표현할 수 있기 위해서는 반드시 두 가지 이상의 척도를 표현할 수 있어야 한다.

• 상하수도학회지
• /
• 제28권1호
• /
• pp.33-45
• /
• 2014

In this study, current sewer infiltration/Inflow(I/I) computation and application method was examined about improvement and adequacy relating to the main issues raised by the field for practitioners. The results of review about infiltration calculation method were considered to be in need of improvement at 'standards of minimum sewage calculation'. Furthermore, the results of review about I/I application method were considered to be in need of improvement at 'standards of seasonal infiltration application' and 'the relative decrease in the Annual evaluation standards'. In addition, annual I/I analysis at JC County for the four years(2009~2012) in respect of operation flow and rainfall data was conducted. The result of annual infiltration analysis, compared average daily sewage generated average infiltration rate was found in 21.95 %, infiltration by unit was found in $0.31m^3/day/cm/km$ and $0.12m^3/day/day$, respectively. The result of annual inflow analysis, average rainfall - Inflow equations was found $y=5.499{\times}$($R^2$ 0.793), and the average Inflow quantity by sewer extension was predicted to $0.66m^3/mm-km$.

• 한국식품위생안전성학회지
• /
• 제3권3호
• /
• pp.105-109
• /
• 1988

순수 참기름을 판정하기 위한 기초자료를 얻기 위하여 사지별에 따른 5종류의 참기름 및 3종류의 채종유를 시료로 하여 TLC 에 의하여 triglyceride를 분획하고 HPLC에 의하여 PN별로 분획하였다. 이상의 결과를 요약하면 다음과 같다. 1) 산지별에 따른 5종류의 참기름은 PN42, 44, 46, 48 및 50의 5획분으로 분획되었으며 그 조성이 동일하여 진위 판정의 자료로 이용 가능하였다. 2) 제주도산 및 전남 채종유의 triglyceride는 PN40~56 획분이 부리 동정되었으며 캐나다산 채종유에서는 PN 36~52의 9획분이 동정되었다. 3) 참기름의 PN별 획분과 비교하여 볼 때 전남 채조유 에서는 PN48, 52, 54 및 56 획분, 제주도 채종유에선 PN42, 52, 54 및 56획분이 유용한 자료가 되었다. 4) 캐나다산의 채종유에서는 PN42, 48 및 52획분의 조성이 특징적이었다. 5) 참기름에 채종유를 4% 혼합한 경우 PN 별 조성으로부터 순수 참기름의 판정이 가능하였지만 이들 data에서 통계적 처리등의 수단으로 더욱 상세히 검토되면 향상된 분석법이 될 것으로 생각된다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제13권9호
• /
• pp.1316-1322
• /
• 2000

Data were compiled and statistically analyzed on the lactation of 50% and 75% Thai native-Friesian crossbred and purebred Friesian cows that were fed at a national institute in Chiang Mai, Thailand. More than 30% higher milk production was obtained in the 75% crossbred compared with that in the 50%, but this amount of milk production in the upgraded breed was still about half that of purebred Friesians; 2,138 kg, least squares means during an average lactation period of 279 days in the 50% crossbred, 2,847 kg during 277 days in the 75% crossbred and 5,585 kg during 308 days in the purebred. Environmental stress due to tropical climate was alleviated by the use of electric fans and water sprinklers in the feeding house during the hot season, and improved diet seemed to enable purebred Friesians to keep their ability to produce a milk quantity of more than 6,500 kg per year. This special care was not given to crossbreds and significantly negative correlations were found between daily minimum temperature and humidity during the initial 100 days of lactation and total milk production and average daily milk yield in the 75% crossbreds. However, these correlations were not found in the 50% crossbreds.

• 치과방사선
• /
• 제10권1호
• /
• pp.57-61
• /
• 1980

In dental roentgenograph it is of mutual benefit to the patient and the dentist to use the minimum amount of radiation capable of producing roentgenograms with maximum interprtive informations. Recent increases in the number of diagnostic x-ray examinations made in this country have caused attention to be paid to the quantity of radiation delivered to the population and operator. The purposes of this study was to assess the quality of dental x-ray units, the amount of films, the average processing procedures and the radiation protection methods in korea. The results were as following: 1. Most of radiation generating system were used in low voltage such as 60Kvp, 10㎃. 2. High sensitivity films such as 'D' group of Kodak or Rinn were mainly used and average 14.7 films used per weeks. 3. Some dentists practiced visual processing technic in simple dark room, and others used instant films. 4. 68.26% of patient held the film themselves, but 27.30% were assisted by dentists film holding. 5. In radiation protection method, 7.85% of dentists had protection equipments such as protective barrier, 2.73% wore protective apron, 27.9% made it a rules to avoid beam, and 7.51% used to maintain a distance from the radiation source.