• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1264-1265
• /
• 2006

Study about the feasibility and effect of high-energy ball milling on a specific Mg alloy under protection medium of alcohol was presented via comparing with conventional vacuum milling. More fine particles with wider powder size distribution but more irregular shape were shown of the powder milled under alcohol. No obvious oxide was revealed from the two kinds of Mg alloy powders with limited milling time. And since slip induced in a preferential direction, the (002) texture was formed in the Mg alloy powders at the initial stage of alcohol milling. More O and Fe contaminants were introduced into the powders milled under alcohol according to the EDS analysis.

• 한국재료학회지
• /
• 제13권9호
• /
• pp.631-634
• /
• 2003

To fabricate W-Cu nanocomposite powder, $WO_3$-CuO powder mixture was high-energetically ball-milled and subsequently hydrogen-reduced. The effect of ball-milling on the hydrogen-reduction behavior of$ WO_3$-CuO was investigated with non-isothermal hygrometric analysis during hydrogen-reduction. Increasing the ball-milling time, the reduction peak temperatures of humidity curves were shifted to low temperature. It was considered that the reduction temperature should be decreased because the specific surface area of each oxide considerably increased with increasing the ball-milling time. In case of ball-milling for 0 h, $WO_3$and CuO were independently hydrogen-reduced and W particles were nucleated on the surface of Cu adjacent to W by CVT. However, in case of ball-milling for 50 h, the aggregates of about 200-300 nm were observed. W particles of size below 30-50 nm were homogeneously distributed with Cu in the aggregates.

• 한국분말재료학회지
• /
• 제25권4호
• /
• pp.291-295
• /
• 2018

A conductive additive is prepared by dispersing multi-walled carbon nanotubes (MWCNTs) on Cu powder by mechanical milling and is distributed in epoxy to enhance its electrical conductivity. During milling, the MWCNTs are dispersed and partially embedded on the surface of the Cu powder to provide electrically conductive pathways within the epoxy-based composite. The degree of dispersion of the MWCNTs is controlled by varying the milling medium and the milling time. The MWCNTs are found to be more homogeneously dispersed when solvents (particularly, non-polar solvent, i.e., NMP) are used. MWCNTs gradually disperse on the surface of Cu powder because of the plastic deformation of the ductile Cu powder. However, long-time milling is found to destroy the molecular structure of MWCNTs, instead of effectively dispersing the MWCNTs more uniformly. Thus, the epoxy composite film fabricated in this study exhibits a higher electrical conductivity than 1.1 S/cm.

• Nuclear Engineering and Technology
• /
• 제34권1호
• /
• pp.60-67
• /
• 2002

The effects of ball-milling time(0 ~4 hrs) have been investigated on the change of powder characteristics, compaction behavior (compaction pressure range : 200 ~400MPa) and sinterability (1700'c in Ha atmosphere) of two different UO$_2$ powders (ex-ADU and ex-AUC) prepared by the wet process. It is observed that, while the ex-ADU UO$_2$ was little affected, the ex-AUC UO$_2$ was largely affected by the ball-milling treatment. This may be attributed to the characteristics of particle size formed during the preparation step, i.e.., the former has a small average size of about 1.0${\mu}{\textrm}{m}$, while the latter has a relatively large average size of about 301n. It appeared that the effective size reduction by ball-milling treatment is limited to the particle size larger than l${\mu}{\textrm}{m}$, and to the extent of maximum decrease in size of about 0.5tn. In the case of ex-AUC UO$_2$, it is observed that the particle size decreased with ball-milling time and green density and sintered density of the pellets prepared from ball-milled powder increased compared with those of pellets prepared from the as-received powder under the same conditions. This may be attributed mainly to the fine particles formed during the ball-milling treatment.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권2호
• /
• pp.19-24
• /
• 2017

Cryogenic milling which is a combined process of low-temperature treatment and mechanical milling was applied to fabricate high critical current density $(J_c)MgB_2$ bulk superconductors. Liquid nitrogen was used as a coolant, and no solvent or lubricant was used. Spherical Mg ($6-12{\mu}m$, 99.9 % purity) and plate-like B powder (${\sim}1{\mu}m$, 97 % purity) were milled simultaneously for various time periods (0, 2, 4, 6 h) at a rotating speed of 500 rpm using $ZrO_2$ balls. The (Mg+2B) powders milled were pressed into pellets and heat-treated at $700^{\circ}C$ for 1 h in flowing argon. The use of cryomilled powders as raw materials promoted the formation reaction of superconducting $MgB_2$, reduced the grain size of $MgB_2$, and suppressed the formation of impurity MgO. The superconducting critical temperature ($T_c$) of $MgB_2$ was not influenced as the milling time (t) increased up to 6 h. Meanwhile, the critical current density ($J_c$) of $MgB_2$ increased significantly when t increased to 4 h. When t increased further to 6 h, however, $J_c$ decreased. The $J_c$ enhancement of $MgB_2$ by cryogenic milling is attributed to the formation of the fine grain $MgB_2$ and a suppression of the MgO formation.

• 공업화학
• /
• 제21권3호
• /
• pp.311-316
• /
• 2010

본 연구는 높은 분산 안정성을 유지하는 antimony-doped tin oxide (ATO) 분산액을 제조하기 위하여, 습식 볼밀법으로 분쇄시간에 따른 ATO의 입자크기, 입도분포, 분산성의 변화를 고찰하였다. 또한 각각의 습식 볼밀 처리된 ATO 분산액의 pH를 변화시켜 ATO 분산액의 분산 특성을 고찰하였다. 습식 볼밀 분쇄 조건에 의하여 ATO의 입자크기 및 입도 분포 변화는 레이저회절 입도분석기와 주사전자현미경을 이용하여 평가하였고, 습식 볼밀 분쇄 시간 및 pH조건에 따른 ATO 입자의 분산성은 제타전위 측정법과 다중광산란(multiple light scattering)법을 이용하여 평가하였다. 분쇄 조건 중 60 min 동안 처리된 ATO 입자 크기는 30% 이하로 작아지고, $1{\sim}35{\mu}m$에서 $0.1{\sim}5{\mu}m$로 입도분포를 갖는 균일한 입자를 얻을 수 있었다. 그러나 분쇄조건을 60 min 이상 처리한 것은 역분쇄 및 재응집 현상의 발생으로 인하여 한계 분쇄 시간이 나타나는 것을 알 수 있었다. 이러한 결과로부터 ATO 분산액은 습식 볼밀 분쇄 시간을 증가시킬수록 입자 크기가 감소하고 표면 에너지가 증가하여 입자간의 반발력이 커지게 됨을 알 수 있었고, 또한 용액의 pH를 증가시킬수록 입자의 표면 이온화도가 커짐으로 인하여 ATO 분산액의 분산성이 향상되는 것을 알 수 있었다.

• 한국식품영양과학회지
• /
• 제41권11호
• /
• pp.1546-1553
• /
• 2012

항산화성 높은 수수의 식품으로서의 이용기술을 개발하여 새로운 소비수요를 창출하고자 도정도가 다른 수수를 이용하여 볶음차를 제조하고 이러한 수수차 제조과정이 수수의 항산화성분 및 항산화활성에 미치는 변화를 살펴보았다. 미도정(0%), 최소 도정(5%), 도정(20%)으로 도정 정도가 다른 수수를 1~10분간 볶음처리하여 항산화성분 및 활성 변화를 살펴본 결과 수수 볶음차의 총 폴리페놀, 플라보노이드 및 탄닌 함량과 DPPH 및 ABTS radical 소거활성은 볶음시간이 길어질수록 증가하다가 7~9분 사이 가장 높은 값을 나타내고 이후 약간 감소하는 경향이었다. 수수의 도정도별로는 미도정 수수를 볶음처리한 수수차에서 페놀성 화합물 및 항산화활성이 총 폴리페놀 12.95 mg GAE/g, 플라보노이드 7.43 mg CE/g 및 DPPH 및 ABTS radical 소거활성 19.97 및 33.11 mg TE/g으로 가장 높았으며, 다음으로 최소 도정 수수 볶음차, 도정 수수 볶음차의 순이었다. 이와는 다르게 도정도별 수수 볶음차의 열수 침출물의 항산화활성은 도정 수수 볶음차에서 가장 높았고, 다음으로 최소 도정 수수 볶음차, 미도정 수수 볶음차의 순이었으며, 이는 수수 볶음차열수 침출액의 색도 및 탁도와 같은 경향으로 도정 수수 볶음차의 경우 종피의 손상에 의해 오히려 열수에 의한 색소 및 항산화성 물질의 용출이 증가한 것으로 생각되었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.555-557
• /
• 2004

We report the effect of the particle size (D50) and PSD (Particle Size Distribution) of glass frit on the transparency of transparent dielectric layer of PDP. The milling efficiency of wet milling with water was the best among the dry milling, wet milling with IPA and wet milling with water. The transparency increased with the reduction of particle size of glass frit as the milling time increased. Also the transparency changed by the PSD of glass frit. Glass frits of broad PSD showed high transparency compared with the glass frits of sharp PSD.

• 한국식품조리과학회지
• /
• 제10권4호
• /
• pp.329-333
• /
• 1994

This study was conducted to examine the expansion characteristics of Jeung pyun prepared by wet-milling and dry-mining rice flours. The fermented time was reduced when the added water was in the higher percentage. The Microstructure of Jelungpyun examined by SEM had a better quality when the added water was 80% for the Jeungpyun by wet-milling and 100% for Jeungpyun by dry-milling. Generally the Jeungpyun by wet-milling had a good fermentation than the Jeungpyun by dry-milling.

• 한국정밀공학회지
• /
• 제15권6호
• /
• pp.58-63
• /
• 1998

There are lots of factors that are related to the geometric characteristics of machined surface. Among them, the tool path and milling mode (up cut milling or down cut milling) are the easiest controllable machining conditions. Thus, the first objective of this research is to study the effects of them on the milled surface that is generated by an end milling tool. To get precision parts, not only the machining process but also the measurement of geometric tolerance is important. But, this measurement requires a lot of time, because the infinite surface points must be measured in the ideal case. So, the second objective is to propose a simple flatness measurement method that can be available instead of the 3-D geometric tolerance measurement method, using a scale factor and characterized points. Finally, it is also shown that the possibility of flatness improvement by shifting the consecutive fine cutting tool path as compared with the last rough cutting tool path.