• 한국정밀공학회지
• /
• 제18권7호
• /
• pp.155-160
• /
• 2001

A milling process with 45 degree chamfered inserts produces a perfect flat surface only in theory. It is due to many unwanted factors including thermal effect, dynamic effect, the problem of the controller used and the problem of accuracy of the machine tool. In this study, introduced is a method to improve the surface roughness by redesigning of the chamfer angle of the insert, which traditionally has been 45 degree. First, the relationship between the fixed machine coordinate and the relative coordinate on the insert is derived. This transfer matrix is used to determine the new insert angle to maximize the flatness of the machined surface. A newly designed insert is manufactured, and used to carry out the experiment. It is proved that she insert designed by the proposed method produced a much flatter surface than a traditional one.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.51-56
• /
• 2001

This work describes reduction of disturbance created by driving actuator in milling process. To the end, controller includes disturbance dynamics. Experimently it is shown that steady disturbance can be rejected to a certain degree.

• 한국분말재료학회지
• /
• 제10권5호
• /
• pp.305-309
• /
• 2003

We report on the formation and chemical leaching of non-equilibrium $Al_{0.6}(Fe_{75}Co_{25})$ alloy produced by rod milling. X-ray diffractometry, transmission electron microscopy, differential scanning calorimetry, scanning electron microscopy, and vibrating sample magnetometry were used to characterize the as-milled and leached specimens. After 400 h, only the $Al_{0.4}Fe_{0.6}$ peak of the body-centered cubic type was present in the XRD pattern. The entire rod milling process could be divided into three different stages of milling: agglomeration, disintegration, and homogenization. The saturation magnetization, $M_s$ decreased with increased milling time, the $M_s$ of the powders before milling was about 113.8 emu/g, the $M_s$ after milling for 400 h was about 11.55 emu/g. Leaching of the Al in KOH of the Al at room temperature from the as-milled powders did not induce any significant change in the diffraction pattern. After the leached specimen had been annealed at $600^{\circ}C$ for 1 hour, the nanoscale crystalline phases were transformed into the bcc Fe, cubic Co, and $CoFe_2O_4$ phases. On cooling the specimen from 85$0^{\circ}C$, the degree of magnetization increased slightly, then increased sharply at approximately 364.8$^{\circ}C$, indicating that the bcc $Al_{0.4}Fe_{0.6}$ phase had been transformed to the Fe and Co phases.

• 한국식품과학회지
• /
• 제12권3호
• /
• pp.182-184
• /
• 1980

벼를 현미(玄米)와 쌀로 가공(加工)할 때 유의(留意)해야 할 가공(加工) 특성(特性)을 구명(究明)하고저 11개(個) 품종(品種)을 대상(對象)으로 하여 시험(試驗)하였던 바 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 제현시(製玄時) 사용(使用)되는 사목(飾目)의 크기에 따른 제현률차(製玄率差)는 현미립(玄米粒)의 넓이 및 두께와 부(負)의 상관(相關)이 있었다. 2. 현백(玄白) 과정(過程)에서 생기는 쇄미률(碎米率)은 현미(玄米) 입장(粒長)과 상관(相關)이 있었다. 3. 공시(供試) 품종중(品種中) 협형(狹形)과 장립종(長粒種)에 해당(該當)되는 것은 없었다. 4. 쌀의 백도(白度)는 동일(同一)한 수준(氷準)의 도정도(搗精度)에서 $12{\sim}32M$의 범위에 폭(幅)넓게 분포(分布)되어 있었다.

• 한국작물학회지
• /
• 제26권3호
• /
• pp.219-225
• /
• 1981

Strong wind of 6.5m/s from electric fan was applied to rice at heading stage to find out the nature of wind damage to panicle. Damaged panicles caused by typhoon were sampled out of field to measure the yield and milling components. Wind-treated glumes were developed into two forms, fertile and sterile, and each of them showed all degree of glume discoloration. The number of fertile grains were higher than sterile grains in a damaged panicle. Averagesdegree of glume discoloration was higher in not flowered glume than in flowered glume. The more recently flowered glumes resulted the higher degree of discoloration among flowered glume. The percent of sterile grain to total number of grains was the highest at stage of just flowering. The glume discoloration representing wind damage at heading state advanced in degree in ten days after treatment compared to that just after treatment. Grain length and grain width were decreased with the increased degree of glume discoloration, while grain thickness was not changed greatly. Chalkiness was a little higher in damaged grain than in normal grain without definite trends by degree of discoloration. Ripening ratio, 1000 grain weight and yield decreased with increased degree of glume discoloration in damaged panicle by typhoon. Decreasing order in yield was white rice, rough rice and brown rice. Ratio of brown rice to rough rice increased, white rice to brown rice decreased, and milling recovery was not changed greatly with increased degree of 히ume discoloration.

• The Journal of Advanced Prosthodontics
• /
• 제11권1호
• /
• pp.55-64
• /
• 2019

PURPOSE. The accuracy of denture bases was compared among injection molding, milling, and rapid prototyping (RP) fabricating method. MATERIALS AND METHODS. The maxillary edentulous master cast was fabricated and round shaped four notches were formed. The cast was duplicated to ten casts and scanned. In the injection molding method, designed denture bases were milled from a wax block and fabricated using SR Ivocap injection system. Denture bases were milled from a pre-polymerized block in the milling method. In the RP method, denture bases were printed and post-cured. The intaglio surface of the base was scanned and surface matching software was used to measure inaccuracy. Measurements were performed between four notches and two points in the mid-palatal suture to evaluate inaccuracy. The palatine rugae resolution was evaluated. One-way analysis of variance was used for statistical analysis at ${\alpha}=.05$. RESULTS. No statistically significant differences in distances among four notches (P>.05). The accuracy of the injection molding method was lower than those of the other methods in two points of the mid-palatal suture significantly (P<.05). The degree of palatine rugae resolution was significantly higher in the injection molding method than that in other methods (P<.05). CONCLUSION. The overall accuracy of the denture base is higher in milling and RP method than the injection molding method. The degree of fine reproducibility is higher in the injection molding method than the milling or RP method.

• 한국분말재료학회지
• /
• 제10권6호
• /
• pp.415-421
• /
• 2003

The study for producing the flake powders by milling of aluminum foil and gas atomized powders was carried out. The effects of lifter bars on the ball motions and milling of aluminum foils were also investigated. The aluminum foils were laminated each other, elongated, fragmented into small foils and finally formed into the flake powders during the dry ball-milling. The spherical atomized-powders were milled to coarse flake powders with high aspect ratio and then changed to fine flake powders with lower aspect ratio. Even though long times were required for making flake powders by milling of foils, the water covering areas of them were higher than those of powders milled using gas-atomized powders, suggesting aluminum foils were more plastically deformed by micro-forging. On the other hand, as the number of lifter bars increased, the necessary rotation speeds of milling jar for cascading mode and cataracting mode decreased drastically. It was possible to achieve same quality of milled flake powder by using the lifter bars under the lower milling speeds. The painting test showed that the appearance of painted surface was good and optimum content range of aluminum paste in car paint to maximize the degree of gloss was 3-5%.

• 한국전기전자재료학회논문지
• /
• 제17권1호
• /
• pp.39-45
• /
• 2004

Fine LaAlO$_3$ powders wore successfully synthesized from La$_2$O$_3$ and ${\gamma}$ $Al_2$O$_3$ powders milling for 10∼50 hours via the high energy milling technique (mechanochemical method) in room temperature and air. The particle size of LaAlO$_3$ powder were estimated from XRD patterns and SEM images to be 160∼180 nm. The LaAlO$_3$ ceramics arc derived for the synthesized powders (milling for 10, 30 and 50 hours) by sintering at 140$0^{\circ}C$ and 150$0^{\circ}C$. The micrographs of grains showed an agglomeration and the degree of agglomeration increased with the milling time. The LaAlO$_3$ made from synthesized powders milling for 50 hours can be sintered to 99.5％ of theoretical density at 150$0^{\circ}C$ for 1 hour. These ceramics exhibits a dielectric constant of 20, a dielectric loss of 0.0003 and a temperature coefficient of capacitance of 15 ppm/$^{\circ}C$ at 1 MHz.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.648-651
• /
• 2003

Fine $LaAlO_3$ powders were successfully synthesized from $La_2O_3$ and ${\gamma}-Al_2O_3$ powders milling for $10{\sim}50hrs$ via the high energy milling technique (mechanochemical methode) in room temperature and air. The particle size of $LaAlO_3$ powder were estimated from XRD patterns and SEM images to be $160{\sim}180nm$. The $LaAlO_3$ ceramics are derived for the synthesized powders (milling for 10, 30 and 50hrs) by sintering at $1400^{\circ}C$. The micrographs of grains showed a agglomeration and the degree of agglomeration increased with the milling time. The $LaAlO_3$ made from synthesized powders milling for 30hrs can be sintered to 98% of theoretical density at $1,400^{\circ}C$ for 4hrs.

• 한국분말재료학회지
• /
• 제25권4호
• /
• pp.291-295
• /
• 2018

A conductive additive is prepared by dispersing multi-walled carbon nanotubes (MWCNTs) on Cu powder by mechanical milling and is distributed in epoxy to enhance its electrical conductivity. During milling, the MWCNTs are dispersed and partially embedded on the surface of the Cu powder to provide electrically conductive pathways within the epoxy-based composite. The degree of dispersion of the MWCNTs is controlled by varying the milling medium and the milling time. The MWCNTs are found to be more homogeneously dispersed when solvents (particularly, non-polar solvent, i.e., NMP) are used. MWCNTs gradually disperse on the surface of Cu powder because of the plastic deformation of the ductile Cu powder. However, long-time milling is found to destroy the molecular structure of MWCNTs, instead of effectively dispersing the MWCNTs more uniformly. Thus, the epoxy composite film fabricated in this study exhibits a higher electrical conductivity than 1.1 S/cm.