• Smart Structures and Systems
• /
• v.17 no.4
• /
• pp.541-557
• /
• 2016

Prefabricated bridge substructures provide new possibility for designers in terms of efficiency of creativity, fast construction, geometry control and cost. Even though prefabricated bridge columns are widely adopted as a substructure system in the bridge construction project recently, lack of deeper understanding of the seismic behavior of prefabricated bridge substructures cause much concern on their performance in high seismic zones. In this paper, experimental research works are presented to verify enhanced design concepts of prefabricated bridge piers. Integration of precast segments was done with continuity of axial prestressing tendons and mild reinforcing bars throughout the construction joints. Cyclic tests were conducted to investigate the effects of the design parameters on seismic performance. An analytical method for moment-curvature analysis of prefabricated bridge columns is conducted in this study. The method is validated through comparison with experimental results and the fiber model analysis. A parametric study is conducted to observe the seismic behavior of prefabricated bridge columns using the analytical study based on strain compatibility method. The effects of continuity of axial steel and tendon, and initial prestressing level on the load-displacement response characteristics, i.e., the strain of axial mild steels and posttensioned tendon at fracture and concrete crushing strain at the extreme compression fiber are investigated. The analytical study shows the layout of axial mild steels and posttensioned tendons in this experiment is the optimized arrangement for seismic performance.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.1
• /
• pp.35-42
• /
• 1984

In the present study, rotating bending fatigue tests have been carried out in three kinds of carbon steel specimens; an annealed low carbon steel, an annealed high carbon steel and quenched-tempered high carbon steel; with a small artificial surface defect that might exist in real structures. Fatigue crack lengths have been observed by a method of replication in order to investigate the growth characteristic of fatigue crack in the viewpoints of strength of materials and fracture mechanics. The main results obtained are as follows: 1) The effect of a small surface defect upon the reduction of fatigue limit is considerably large, and the rate of fatigue limit reduction grows in the following order; annealed low carbon steel(mild steel), annealed high carbon steel, quenched-tempered high carbon steel. 2) When the growth rate of surface crack length(2a) was investigated in the viewpoints of fracture mechanics based upon $ ${\Delta}K_{\varepsilon}$, the dependence of stress level and of surface defect size disappear, and there exists a linear relationships between d(2a)/dN and ${\Delta}K_{{\varepsilon}t},\;\Delta_{{\varepsilon}t}\sqrt{{\pi}a}$, on log. plot, i.e, $d(2a)/dN={C{\cdot}{\Delta}K_{\varepsilon}}^3_t$, where ${\Delta}_{{\varepsilon}t}\sqrt{{\pi}a}$ a is the cyclic total strain intensity factor range.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.403-411
• /
• 1999

The steel plate for shadow mask is used in a Cathode-ray tube of TV monitor and is the strictest product in surface quality because hundreds thousand of holes are perforated in a plane of 25 ${\times}$25 inches. To mass-produce this product, a reversible cold rolling mill for silicon steel was used and the rolling technology and the activity for quality improvement are described in this work. Because the steel plate is a mild steel, which is very sensitive to strip-breakage even in a low tension, we reset the minimum tension values matching to the operating conditions. The roll mark due to the multi-segmented araangement of shape controlling roll was prevented by hardening the intermediate shape controlling roll and by changing the existing working-roll into a HSS (Hig Speed Steel) roll. The scratch caused by the speed difference between a idle roll and a strip was prevented by increasing the roll roughness. With these activities, the steel plate for shadow mask can be stable. The continuous improvement of quality is, however, required for the customer satisfaction both of domestic and overseas market.

• Steel and Composite Structures
• /
• v.42 no.1
• /
• pp.33-48
• /
• 2022

This paper researches a lightweight composite structure referred to as the Profiled Steel Sheeting Dry Board (PSSDB). It is fundamentally produced by connecting a Profiled Steel Sheeting to Dry Board using mechanical screws. It is mainly employed as floor panels. However, almost all studies have focused on researching the one-way structural performance. Therefore, this study focuses on the bending behaviour of the two-way PSSDB floor system using both of Finite Element (FE) and Experimental analysis. Four panels were used in the experimental tests, and a mild steel plate has been applied at the bottom for two panels. For the FE process, models were created using ABAQUS software. 4 parametric studies have been utilized to understand the system's influential elements. From the experimental tests, it was found that using Steel Plate shall optimize the two-way action of the system and depending on the type of dry board the improvement in stiffness may reach up to 38%. It was shown from the FE analysis that the dry board, profiled steel sheeting and steel plat can affect the system by up to 10 %, 17% and 3% respectively, while applying a uniform load demonstrate a better two-way action.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.11a
• /
• pp.73-77
• /
• 1989

Ashby등에 의해 비윤활상태에서의 steel의 마모기구도(wear mechanism map)가 작성 발표된바 있다. 이 마모기구도는 지금까지 발표된 steel의 마모연구의 결과를 모아서 seizure, melt dominiated 마모, 산화지배 마모, 소성지배 마모등의 기구가 지배되는 영역을 표준화된 압력과 속도의 변화에 따라 표시한 것이다. 본 연구에서는 베아링강을 모델제료로 하여 마모 diagram을 작성하여 속도와 하중 변화에 따른 mild wear에서 severe wear로의 천이를 관찰하고 각 영역에서의 마모기구에 대해 논하고자 한다. 이 연구에서는 윤활유의 영향을 배제하고 steel ring과 steel pin간의 비윤활 상태에서 마모시험이 행하여졌다. 본 실험에서는 다목적 마모시험을 사용하여 시간에 따라 접촉면적의 형상이 비교적 변하지 않는 pin on ring형태의 시편을 사용하였다. 9.8 N 으로 부터 98 N까지의 하중이, 0.012 m/sec에서 0.012 m/sec까지의 미끄럼 속도에서 마모실험을 행하였다. 각 조합에 따른 조건에서의 마모된 양은 시편의 변이를 측정하여 마모부피를 추정계산하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.65-74
• /
• 2004

The inherent strain method is known to be very efficient in predicting the deformation of steel plate by line heating. However, in the actual line heating process in shipyard, the rapid quenching changes the phase of steel. In this study, In order to consider additional effects under phase transformation, inherent strain regions were assumed to expand. Also, when calculating inherent strain, material properties of steel in heating and cooling are applied differently considering phase transformation. In this process, a new method which can reflect thermal volume expansion of martensite is suggested.8y the suggested method, it was possible to predict the plate deformations by line heating more precisely.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.565-573
• /
• 1999

Hihg Tensile Steel enables to reduce the plate thickness comparing to the case when Mild Steel is used. From the economical view points this is very preferable since the reduction in the hull weight. however to use the High Tensile Steel effectively the plate thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling the flexural rigidity of the cross sect6ion of a ship's hull also decreases. This may lead to excessive deflection of the hull girder under longitudinal bending. In these cases a precise estimation of plate's behavior after buckling is necessary and nonliner analysis of isolated and stiffened plates is required for structural sys-tem analysis. In this connection this paper discusses nonlinear behaviour of thin plate under thrust. Based on the analytical method elastic large deflection analysis of isolated plate is perform and simple expression are derived to evaluated the inplane rigidity of plates subjected to uniaxial compression.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1873-1875
• /
• 2005

The effect of zinc oxide as an inhibitor for the corrosion of steel in concrete environment was studied by weight loss measurements, potential-time behaviour and anodic polarization technique. The salient features of the investigation were: in 100% OPC extracts, the passivity of steel was readily destroyed, however extracts containing various concentration of zinc oxide, the passivity of steel was maintained even in the presence of 30,000 ppm of chloride. Alkalinity of concrete was maintained by the addition of zinc oxide. The efficiency of the inhibitor was found to increase with increasing inhibitor concentration. Addition of zinc oxide in the range 3 to 4% by weight of cement was sufficient to protect the rebars.

• Journal of the Korean Society of Safety
• /
• v.2 no.3
• /
• pp.5-11
• /
• 1987

In this study, a mild steel (SS41) of the carbon steel, a spring steel (SUP-9), and stainless steel (SUS 304) of the special gceel, etc, are adopted as the experimental materrials and are weded by $CO_2$(SS41, SUP-9), TIG (SUS304), respectively. And the residual stress distribution and fracture behavior at the welded zone are examined according to annealing temperatures of four section involving as welded. As a consequence, the best annealing temperatures that the residual stress is removed enough and mechanical properties are very suitable are at 90$0^{\circ}C$ (SS41), 75$0^{\circ}C$ (SUP-9), 110$0^{\circ}C$ (SUS 304), respectively.

• Journal of Welding and Joining
• /
• v.20 no.1
• /
• pp.55-61
• /
• 2002

The automobile is made up of about twenty thousand parts. Some parts are formed by pressing and combined by spot welding. Among them, steel palate of fuel tank is formed in the metal mold and bending parts are jointed by spot and seam welding. To find weldability conditions of spot welding, clearance between two welding steel plates was made and after spot welding, weldability is evaluated by means of tensile shear load, nugget size and shape. Specimen used in this study was a mild steel of 1.2mm thickness and electrode was Cu-Cr alloy of 6mm diameter. When spot welding started, the clearance of two steel plates was changed 0mm, 3mm and 5mm step by step. The fractured surface of specimen after this test was observed by Optical Microscope to measure microstructure and nugget shape. When clearance of two specimen was 3mm and 5mm, strength and nugget size was decreased and nugget shape was not clear.