• Journal of Welding and Joining
• /
• v.20 no.5
• /
• pp.127-133
• /
• 2002

In this study, metal transfer characteristics in pulsed current metal inert gas (MIG) welding of aluminum was investigated. Based on the metal transfer characteristics from direct current electrode negative MIG welding, the one drop per one pulse(ODOP) condition was predicted and compared with experimental data. The results indicated that experimental pulse range for the ODOP condition is wider than that predicted from the DCEP MIG welding data. In addition, more stable metal trnasfer behavior was obtained at the higher end of the ODOP condition.

• Journal of Welding and Joining
• /
• v.21 no.2
• /
• pp.57-63
• /
• 2003

Since new types of vehicles or structures made from thin aluminum alloy are under rapid development and some products are already on the market, welding of aluminium sheet is increasing. MIG(Metal Inert Gas), MIG-Pulse, TIG(Tungsten Inert Gas) welding are the typical Ai welding. MIG welding has the advantage of high speed, but it is difficult to apply to the thin plate, because of bum-through by the high heat input and spatter. MIG-Pulse welding can weld without spatter and burn-through, but when the gap exists at the welding joint, there is quite a possibility of bum-through. TIG welding is difficult to weld at a high speed. AC Pulse welding alternates between DCEP(Direct Current Electrode Positive) and DCEN(Direct Current Electrode Negative). DCEN is higher wire melting rate than DCEP, while lower temperature of droplet than DCEP. In AC Pulse welding, far fixed welding current, wire melting rate increases as the EN ratio increases. For fixed wire feed rate, welding current decreases as the EN ratio increases. Because of these features, the temperature of droplet, the depth of penetration, the width of bead decrease and the reinforcement height increases as EN ratio increases, and these are able to weld at a high speed, lower heat input. It is the purpose of this study that design of AC pulse current waveform for MIG welding of Al sheet and estimation of output characteristic.

• IMMUNE NETWORK
• /
• v.2 no.1
• /
• pp.12-18
• /
• 2002

Interferon-${\gamma}$ (IFN-${\gamma}$) is well known as a potent inducer in monokine induced by IFN-${\gamma}$ (Mig) mRNA expression. Although lipopolysaccharide (LPS) alone is weakly effective on Mig mRNA expression. the stimulation of LPS and IFN-${\gamma}$ (LPS/IFN-${\gamma}$ simultaneously has been shown to synergize to produce a high level of Mig mRNA in mouse peritoneal macrophages. In this study, interleukin-10 (IL-10) was found to suppress the LPS/IFN-${\gamma}$-induced Mig mRNA expression in cell type- and mouse strain-specific fashion, but IFN-${\gamma}$ alone-induced Mig mRNA was unaffected by IL-10 under identical experimental conditions. The IL-10-mediated suppression of LPS/IFN-${\gamma}$-stimulated Mig mRNA expression was dependent on the concentration of IL-10, and was prevented when the agent was added 2 hours after LPS/IFN-${\gamma}$ treatment. The suppressive action of IL-10 was dependent on a protein synthesis. However, IL-10 did not reduce the stability of LPS/IFN-${\gamma}$-induced Mig mRNA. These data may have important implications for a previously unrecognized role for IL-10 as a regulator of synergistic effect of LPS on the IFN-${\gamma}$-induced expression of the Mig gene in macrophages.

• Journal of Gastric Cancer
• /
• v.15 no.4
• /
• pp.270-277
• /
• 2015

Purpose: Minimally invasive gastrectomy (MIG), including laparoscopic distal subtotal gastrectomy (LDG) and robotic distal subtotal gastrectomy (RDG), is performed for gastric cancer, and requires a learning period. However, there are few reports regarding MIG by a beginner surgeon trained in MIG for gastric cancer during surgical residency and fellowship. The aim of this study was to report our initial experience with MIG, LDG, and RDG by a trained beginner surgeon. Materials and Methods: Between January 2014 and February 2015, a total of 36 patients (20 LDGs and 16 RDGs) underwent MIG by a beginner surgeon during the learning period, and 13 underwent open distal subtotal gastrectomy (ODG) by an experienced surgeon in Bundang CHA Medical Center. Demographic characteristics, operative findings, and short-term outcomes were evaluated for the groups. Results: MIG was safely performed without open conversion in all patients and there was no mortality in either group. There was no significant difference between the groups in demographic factors except for body mass index. There were significant differences in extent of lymph node dissection (LND) (D2 LND: ODG 8.3% vs. MIG 55.6%, P=0.004) and mean operative time (ODG 178.8 minutes vs. MIG 254.7 minutes, P<0.001). The serial changes in postoperative hemoglobin level (P=0.464) and white blood cell count (P=0.644) did not show significant differences between the groups. There were no significant differences in morbidity. Conclusions: This study showed that the operative and short-term outcomes of MIG for gastric cancer by a trained beginner surgeon were comparable with those of ODG performed by an experienced surgeon.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1563-1570
• /
• 2023

In this study, a DeCART/MIG uncertainty quantification (UQ) analysis code system with a multicorrelated cross section stochastic sampling (S.S.) module was established and verified through the UAM (Uncertainty Analysis in Modeling) and the BEAVRS (Benchmark for Evaluation And Validation of Reactor Simulations) benchmark calculations. For the S.S. calculations, a sample of 500 DeCART multigroup cross section sets for two major actinides, i.e., ²³⁵U and ²³⁸U, were generated by the MIG code and covariance data from the ENDF/B-VII.1 evaluated nuclear data library. In the three pin problems (i.e. TMI-1, PB2, and Koz-6) from the UAM benchmark, the uncertainties in k_inf by the DeCART/MIG S.S. calculations agreed very well with the sensitivity and uncertainty (S/U) perturbation results by DeCART/MUSAD and the S/U direct subtraction (S/U-DS) results by the DeCART/MIG. From these results, it was concluded that the multi-group cross section sampling module of the MIG code works correctly and accurately. In the BEAVRS whole benchmark problems, the uncertainties in the control rod bank worth, isothermal temperature coefficient, power distribution, and critical boron concentration due to cross section uncertainties were calculated by the DeCART/MIG code system. Overall, the uncertainties in these design parameters were less than the general design review criteria of a typical pressurized water reactor start-up case. This newly-developed DeCART/MIG UQ analysis code system by the S.S. method can be widely utilized as uncertainty analysis and margin estimation tools for developing and designing new advanced nuclear reactors.

• Journal of Welding and Joining
• /
• v.23 no.1
• /
• pp.69-76
• /
• 2005

Recently, application of arc welding to galvanized carbon steel sheet is on the increasing Ould in the fields of automobile and construction industries. In arc welding process, zinc is evaporated in weld pool, even under the appropriate welding condition and produce blowhole and/or pit. Zinc gas cause instability of arc and increase spatter and fume. This research is purposed to minimize the heat-input and the formation of porosities in the welded joint of the galvanized carbon steel sheet using variable polarity AC wave pulse MIG welding system. An appropriate welding condition which showed low spatter and good bead appearance was acquired by applying the AC pulse MIG welding machine to DC duplicated MIG welding with the solid wire. When oxygen gas was added to shield gas of MIG welding for galvanized steel sheet, arc length was increased and arc stability was improved. In the AC duplicated welding, the loss of galvanized layer was decreased as the amount of heat-input was decreased when the EN ratio was increased under the condition that average welding current was evenly set.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.4272-4279
• /
• 2022

In this study, a cross section stochastic sampling (S.S.) capability is implemented into both the McCARD continuous energy Monte Carlo code and MIG multiple-correlated data sampling code. The ENDF/B-VII.1 covariance data based 30 group cross section sets and the SCALE6 covariance data based 44 group cross section sets are sampled by the MIG code. Through various uncertainty quantification (UQ) benchmark calculations, the McCARD/MIG results are verified to be consistent with the McCARD stand-alone sensitivity/uncertainty (S/U) results and the XSUSA S.S. results. UQ analyses for Three Mile Island Unit 1, Peach Bottom Unit 2, and Kozloduy-6 fuel pin problems are conducted to provide the uncertainties of k_eff and microscopic and macroscopic cross sections by the McCARD/MIG code system. Moreover, the SNU S/U formulations for uncertainty propagation in a MC depletion analysis are validated through a comparison with the McCARD/MIG S.S. results for the UAM Exercise I-1b burnup benchmark. It is therefore concluded that the SNU formulation based on the S/U method has the capability to accurately estimate the uncertainty propagation in a MC depletion analysis.

• Journal of Welding and Joining
• /
• v.5 no.4
• /
• pp.47-53
• /
• 1987

The purpose of this study is to reexamine our test method in the light ofstatistical methods for data interpretation. Our trial to apply Plackett-Burman statistical model in multifactorial welding experiments shows that is saves much time and cost and extracts very accurate results. In this study, the parametric effects of bead shape on pulse MIG process in Cu-Ni alloy are investigated for verifying our trial.

• Journal of Korea Foundry Society
• /
• v.32 no.2
• /
• pp.109-113
• /
• 2012

• Journal of the Korean Magnetics Society
• /
• v.6 no.1
• /
• pp.7-14
• /
• 1996

According to demands of high density and wide band magnetic recording systems, a composite MIG head was developed. This head has the sufficient performance for use of a SD VCR : its characteristics are a good recoding performance, a low rubbing noise, a good frequency dependence of efficiency, and a good compatibility with ME tape. In a SD VCR system, the C/N value of a composite MIG head at 20.92MHz was 51 dB.