• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.8
• /
• pp.1-10
• /
• 2008

In this paper, we describe a design of a 128bit MRAM based on a new switching architecture which is Local Field Switching(LFS). LFS uses a local magnetic field generated by the current flowing through an MTJ. This mode reduces the writing current since small current can induce large magnetic field because of close distance between MTJ and the current. It also improves the cell selectivity over using conventional MTJ architecture because it doesn't need a digit line for writing. The MRAM has 1-Transistor 1-Magnetic Tunnel Junction (IT-1MTJ) memory cell structure and uses a bidirectional write driver, a mid-point reference cell block and a current mode sense amplifier. CMOS emulation cell is adopted as an LFS-MTJ cell to verify the operation of the circuit without the MTJ process. The memory circuit is fabricated using a $0.18{\mu}m$ CMOS technology with six layers o) metal and tested on custom board.

• International Journal of Fluid Machinery and Systems
• /
• v.10 no.3
• /
• pp.287-295
• /
• 2017

The most detrimental pressure pulsations in high-head pump-turbines is caused by the rotor-stator interaction (RSI) between the guide vanes and runner blades. When the pump-turbine operates in the S-shaped region of the characteristic curves, the deteriorative flow structures may significantly strengthen RSI, causing larger pressure pulsations and stronger vibration with an increased risk of mechanical failure. CFD simulations were carried out to analyze the impacts of flow evolution on the pressure pulsations in the S-shaped region of a model pump-turbine. The results show that the reverse flow vortex structures (RFVS) at the runner inlet have regular development and transition patterns when discharge reduces from the best efficiency point (BEP). The RFVS first occur at the hub side, and then shift to the mid-span near the no-load point, which cause the strongest pressure pulsations. The locally distributed RFVS at hub side enhance the local RSI and makes the pressure fluctuations at the corresponding sections stronger than those at the rest sections along the spanwise direction. Under the condition of RFVS at the mid-span, the smaller flow rate make the smaller difference of pressure pulsation amplitudes in the spanwise direction. Moreover, the rotating stall, rotating at 35.7%-62.5% of the runner rotational frequency, make the low frequency components of pressure pulsations distribute unevenly along the circumference in the vaneless space. However, it have little influence on the distributions of high components.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.29 no.2
• /
• pp.23-29
• /
• 1987

This study was fulfilled by the floating lysimeter method at the experimental farm of Kon-Kuk University from August to November of 1986 to investigate the amount of evapotranspiration by the growing periods, evapotranspiration ratio, amount of watering per one time, days of intermission, soil moisture extraction pattern and crop coefficient of the Chinese cabbage cultivated in the sandy loam soil at the watering point of pF2.O. The results obtained are summarized as follows: 1.The total evapotranspiration during the growing period was 267.2mm, which was 3. 99mm by daily average, and the maximum evapotranspiration showed in the mid ten days of September with the value of 5.81mm I day. 2.The evapotranspiration ratio by the growing stages increased from the last ten days of September and showed maximum in the beginning of October, and the average evapotranspiration ratio was 1.4. 3.The days of watering intermission at the watering point of pF2.O was 2.4 days, and the average yield per plant was 3,228 g. 4. The soil moisture extraction pattern in the initial stage was 78.9 % in the 1st and 2nd soil layer and 21.1 % in the 3rd and 4th layer, and the mid-season stage, the moisture extraction proportion of the under layer accounted for 38.8 % which showed that the root elongated to the lowest soil layer. 5.The average crop coefficient(Kc) of the tested crop during the growing period was 0.67 by Penman equation and 2.36 by Pan Evaporation equation, which showed high difference by the calculation methods, and the changes of crop coefficient by the growing stages by Penman equation was favorable than those calculated by other met-hods.

• Journal of the Korean earth science society
• /
• v.24 no.3
• /
• pp.181-189
• /
• 2003

This study analyzes the results of thunderstorm data observed in the mid-western part of Japan during the winter of 1996-1997. There were 35 instances of thunderstorms with 4,426 instances of lightning detected during the observation period. This study estimates the frequency of lightning occurrence through classification of detected lightning into two types, and analyzes the relationship between lightning types and synoptic pattern. According to the analyzed results, cloud-to-cloud discharge and positive polarity occupied 78% and 42.3% of total discharge, respectively. It is rare for lightning to occur in the winter season, usually occuring during the night (midnight to 5 a.m.). Lightning frequently occurs when there is a prevailing synoptic wind from the norhwest. According to the analyzed results of multiplicity and multi-point lightning, the mean values of multiplicity and multi-point lightning are 1.4 and 1.2, respectively.

• Steel and Composite Structures
• /
• v.9 no.2
• /
• pp.131-158
• /
• 2009

This paper presents a modelling technique for the nonlinear analysis of composite steel-concrete beams with partial shear interaction. It extends the applicability of two stiffness elements previously derived by the authors using the direct stiffness method, i.e. the 6DOF and the 8DOF elements, to account for material nonlinearities. The freedoms are the vertical displacement, the rotation and the slip at both ends for the 6DOF stiffness element, as well as the axial displacement at the level of the reference axis for the 8DOF stiffness element. The solution iterative scheme is based on the secant method, with the convergence criteria relying on the ratios of the Euclidean norms of both forces and displacements. The advantage of the approach is that the displacement and force fields of the stiffness elements are extremely rich as they correspond to those required by the analytical solution of the elastic partial interaction problem, thereby producing a robust numerical technique. Experimental results available in the literature are used to validate the finite element proposed in the paper. For this purpose, those reported by Chapman and Balakrishnan (1964), Fabbrocino et al. (1998, 1999) and Ansourian (1981) are utilised; these consist of six simply supported beams with a point load applied at mid-span inducing positive bending moment in the beams, three simply supported beams with a point load applied at mid-span inducing negative bending moment in the beams, and six two-span continuous composite beams respectively. Based on these comparisons, a preferred degree of discretisation suitable for the proposed modelling technique expressed as a function of the ratio between the element length and depth is proposed, as is the number of Gauss stations needed. This allows for accurate prediction of the nonlinear response of composite beams.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.4
• /
• pp.221-230
• /
• 2021

This paper proposes full waveform inversion (FWI) for estimating the physical properties of a layered half-space. An FWI solution is obtained using a genetic algorithm (GA), which is a well-known global optimization approach. The dynamic responses of a layered half-space subjected to a harmonic vertical disk load are measured and compared with those calculated using the estimated physical properties. The responses are calculated using the thin-layer method, which is accurate and efficient for layered media. Subsequently, a numerical model is constructed for a layered half-space using mid-point integrated finite elements and perfectly matched discrete layers. An objective function of the global optimization problem is defined as the L2-norm of the difference between the observed and estimated responses. A GA is used to minimize the objective function and obtain a solution for the FWI. The accuracy of the proposed approach is applied to various problems involving layered half-spaces. The results verify that the proposed FWI based on a GA is suitable for estimating the material properties of a layered half-space, even when the measured responses include measurement noise.

• Journal of Advanced Navigation Technology
• /
• v.27 no.2
• /
• pp.182-189
• /
• 2023

Depth estimation is a key technology in 3D map generation for autonomous driving of vehicles, robots, and drones. The existing sensor-based method has high accuracy but is expensive and has low resolution, while the camera-based method is more affordable with higher resolution. In this study, we propose self-attention-based unsupervised monocular depth estimation for UAV camera system. Self-Attention operation is applied to the network to improve the global feature extraction performance. In addition, we reduce the weight size of the self-attention operation for a low computational amount. The estimated depth and camera pose are transformed into point cloud. The point cloud is mapped into 3D map using the occupancy grid of Octree structure. The proposed network is evaluated using synthesized images and depth sequences from the Mid-Air dataset. Our network demonstrates a 7.69% reduction in error compared to prior studies.

• Radiation Oncology Journal
• /
• v.16 no.3
• /
• pp.325-335
• /
• 1998

Purpose : Since the mid cranial fossa is composed of various thickness of bone, the tissue inhomogeneity caused by bone would produce dose attenuation in cobalt-60 gamma knife irradiation. The correction factor for bone attenuation of cobalt-60 which is used for gamma knife source is -3.5$\%$. More importantly, nearly all the radiosurgery treatment planning systems assume a treatment volume of unit density: any perturbation due to tissue inhomogeneity is neglected, This study was performed to confirm the bone attenuation in mid cranial fossa using gamma knife. Materials and Methods : Computed tomography was performed after Leksell stereotactic frame had been liked to the Alderson Rando Phantom (human phantom) skull area. Kodak X-omat V film was inserted into two sites of pituitary adenoma point and acoustic neurinoma point, and irradiated by gamma knife with 14mm and 18mm collimator. An automatic scanning densitometer with a 1mm aperture is used to measure the dose profile along the x and y axis. Results : Isodose curve constriction in mid cranial fossa is observed with various ranges. Pituitary tumor point is greater than acoustic neurinoma point (0.2-3.0 mm vs 0.1-1.3 mm) and generally 14 mm collimator is greater than 18mm collimator (0.4-3.0 mm vs. 0.2-2.2 mm) Even though the isodose constriction is found, constriction of 50$\%$ isodose curve which is used for treatment reference line does not exceed 1 mm. This range is too small to influence the treatment planning and treatment results. Conclusion : Radiosurgery planning system of gamma knife does not show significant error to be corrected without consideration of bone attenuation.

• Wind and Structures
• /
• v.9 no.4
• /
• pp.315-330
• /
• 2006

Flow and scalar dispersion around Cheomseongdae are numerically investigated using a three-dimensional computational fluid dynamics (CFD) model with the renormalization group (RNG) $k-{\varepsilon}$ turbulence closure scheme. Cheomseongdae is an ancient astronomical observatory in Gyeongju, Korea, and is chosen as a model obstacle because of its unique shape, that is, a cylinder-shaped architectural structure with its radius varying with height. An interesting feature found is a mid-height saddle point behind Cheomseongdae. Different obstacle shapes and corresponding flow convergences help to explain the presence of the saddle point. The predicted size of recirculation zone formed behind Cheomseongdae increases with increasing ambient wind speed and decreases with increasing ambient turbulence intensity. The relative roles of inertial and eddy forces in producing cavity flow zones around an obstacle are conceptually presented. An increase in inertial force promotes flow separation. Consequently, cavity flow zones around the obstacle expand and flow reattachment occurs farther downwind. An increase in eddy force weakens flow separation by mixing momentum there. This results in the contraction of cavity flow zones and flow reattachment occurs less far downwind. An increase in ambient wind speed lowers predicted scalar concentration. An increase in ambient turbulence intensity lowers predicted maximum scalar concentration and acts to distribute scalars evenly.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1227-1234
• /
• 1994

A cold spot temperature control system for the batch annealing furnace has been established in order to reduce energy consumption which is essential to improve productivity and stabilize the properties of products. A relationship between annealing cycle time and gas flow rate is developed and also for the variation of coil cold spot temperature with time during heating, and actual temperature measurements at mid-width of each coil during soaking. The results of the temperature variation effect on the cold rolled steel sheet batch annealing are as follows. (1) Cooling rate increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component change. (2) In case of short time heating, the slowest heating part is the center of B coil and in case of ling time heating, the low temperature point moves from the center of coil to inside coil. (3) The outside of top coil is the highest temperature point under heating, which becomes the lowest temperature point under cooling. (4) Soaking time determination depends on the input coil width, and soaking time for quality homogenization of 1214 mm width coil must be 2 hours longer than that of 914 mm width coil.