• Journal of the Semiconductor & Display Technology
• /
• v.13 no.4
• /
• pp.59-63
• /
• 2014

Previous studies have selected wireless power transmission system using 2.45 GHz of ISM band, but the researches for 5.8 GHz microwave wireless power transmission have been relatively rare. The 5.8 GHz has some advantages compared with 2.45 GHz. Those are smaller antenna and smaller integrated system for RFIC. In this paper, the 5.8 GHz wireless power transmission system was developed and transmission efficiency was measured according to the distance. A transmitter sent the amplified microwaves through an antenna amplified by a power amplifier of 1W for 5.8 GHz, and a receiver was converted to DC from RF through a RF-DC Converter. In the 1W 5.8GHz wireless power transmission system, the converted currents and voltages were measured to evaluate transmission efficiency at each distance where LED lights up to 1m. The RF-DC Converter is designed and fabricated by impedance matching using full-wave rectifier circuit. The transmission-efficiency of the system shows from 1.05% at 0cm to 0.095% at 100cm by distance.

• Journal of IKEEE
• /
• v.25 no.2
• /
• pp.234-242
• /
• 2021

In case implementation of microwave photonic (MWP) systems for phased array radars (PARs), noise and time delay error should be minimized to obtain accurate beam direction. Time delay error in MWP systems is generated from signal noise and timing jitter. In this paper, noise and timing jitter in MWP systems for PAR is researched, also according to the amplification of an erbium-doped fiber amplifier, noise and timing jitter variation is verified by an experiment. Timing jitter is decreased and SNR is increased if we amplify the signal by using an erbium-doped fiber amplifier, up to the amplification rate of signal and noise is similar.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.264-272
• /
• 2009

In this paper, a Ka-band 10 W power amplifier module is designed and fabricated using MIC(Microwave Integrated Circuit) module technology which combines multiple power MMIC(Monolithic Microwave Integrated Circuit) chips on a thin film substrate. Modified Wilkinson power dividers/combiners are used for millimeter wave modules and CBFGC-PW-Microstrip transitions are utilized for reducing connection loss and suppressing resonance in the high-gain and high-power modules. The power amplifier module consists of seven MMIC chips and operates in a pulsed mode. for the pulsed mode operation, a gate pulse control circuit supplying the control voltage pulses to MMIC chips is designed and applied. The fabricated power amplifier module shows a power gain of about 58 dB and a saturated output power of 39.6 dBm at a center frequency of the interested frequency band.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.11
• /
• pp.50-55
• /
• 2009

In this paper, a distributed amplifier is designed using distributed network synthesis that provides the optimum absorption capability of a capacitance. Transfer functions of filters, which consist of the amplifier, are synthesized by a low-pass Chebyshev approximation. Capacitances that a filter network can absorb are calculated as a function of its minimum insertion loss(MIL) and ripple. Active devices in a distributed amplifier are modeled as equivalent circuits by using their S-parameters, and their equivalent capacitances are absorbed into filter structures by properly adjusting the MIL and ripple of a transfer function. As an application example, a distributed amplifier with the gain of about 12.5dB is designed that operates over the frequency range between 0.1 and 7.5GHz. Experimental results prove that distributed network synthesis, which considers capacitance absorption capability, is useful to the design of distributed amplifiers.

• ETRI Journal
• /
• v.30 no.1
• /
• pp.158-160
• /
• 2008

A highly linear and efficient GaN HEMT Doherty amplifier for wideband code division multiple access (WCDMA) repeaters is presented. For better performance, the adaptive gate bias control of the peaking amplifier using the power tracking circuit and the shunt capacitors is employed. The measured one-carrier WCDMA results show an adjacent channel leakage ratio of -43.2 dBc at ${\pm}2.5$-MHz offset with a power added efficiency of 40.1% at an average output power of 37 dBm, which is a 7.5 dB back-off power from the saturated output power.

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.136-140
• /
• 1990

A hybrid wideband amplifier having bandwidth from 5MHz to 2000MHz with a gain of 10db$\pm$3dB is designed and implemented by using a lossy matched network and GaAs FET. The implemented amplifier circuit operates as a capacitor-resistor(C-R) coupled amplifier circuit in the low frequency range (below 800 MHz) in which {{{{ LEFT $\mid$ S_{21 } RIGHT $\mid$ }} for the GaAs FET is constant. It also operates as a lossless impedance matching circuit in the microwave frequency range in which S21 for the GaAs FET has a slope of approximately -6dB/octave. Using this configuration technique, Two stage GaAs FET amplifier implemented is measured to 10dB gain within a 3dB fluctuation over the frequency band from 5 to 2000MHz.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.3 no.1
• /
• pp.11-19
• /
• 1992

To design of Ultra-wideband amplifier, we analyzed the inductor peaking to reduce the capacitance effect of GaAs MESFET in upper frequency edge. And we deduced an optimun inductor peaking element from transfer function of GaAs MESFET small-signal equivalent circut and realized the Feedback Amplifier Module (FAM) having flat gain. We design the imput and output impe dance matching networks by Real-Frequency Method. It show that the gain of designed amplifier has a 6.38dB with gain variation 0.56 at 0.1~12 GHz frequency gand by computer simu-lation.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.52 no.1
• /
• pp.28-34
• /
• 2003

In this paper, a predistortion linearizer using series diode is proposed for linearizing the power amplifier in microwave radio systems. The power amplifier should be operated near saturation region to achieve high efficiency. But at this region, amplitude and phase distortions of the amplifier remarkably increase with the increase of input power and cause a significant adjacent channel interference. The linearizer is composed of a series diode with a parallel capacitor, which provides positive amplitude and negative phase deviations with the increasing input power. This type of linearizer using the nonlinearity of diode has improved the C/I(Carrier to Intermodulation Distortion) ratio well. By applying this linearizer to two-tone 880MHz power amplifier, adjacent channel leakage power is improved up to 5dBm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.4
• /
• pp.501-505
• /
• 2015

In this paper, we demonstrated a 4W power amplifier monolithic microwave integrated circuit (MMIC) for Ku-band satellite communication applications. The used device technology relies on $0.25{\mu}m$ GaAs pseudomorphic high electron mobility transistor (PHEMT) process. The 4W power amplifier MMIC has linear gain of over 30 dB and saturated output power of over 36.1 dBm in the frequency range of 13.75 GHz ~ 14.5 GHz. Power added efficiency (PAE) is over 30 %.

• ETRI Journal
• /
• v.35 no.4
• /
• pp.718-721
• /
• 2013

This letter proposes a novel calibration method for a multiport amplifier (MPA) to achieve optimum port-to-port isolation by correcting both the amplitude and phase of the calibration signals. The proposed architecture allows for the detection of the phase error and amplitude error in each RF signal path simultaneously and can enhance the calibrated resolution by controlling the analog phase shifters and attenuators. The designed $2{\times}2$ and $4{\times}4$ MPAs show isolation characteristics of 30 dB and 27 dB over a frequency range of 19.5 GHz to 22.5 GHz, respectively.