• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.120-126
• /
• 2006

Ferroelectric materials have been widely investigated for high density dynamic random access memories, opto-electrics, and tunable microwave devices due to their properties. In this study, we have investigated the dielectric properties of Ti doped $K(Ta,\;Nb)O_3$ thin films. By doping Ti Into the $K(Ta,Nb)O_3$ system, Ti with a valence value of +4 will substitute Ta or Nb ions with a valence value of +5. This substitution will introduce an acceptor state. Therefore, this introduced acceptor state will reduce dielectric loss by trapping electrons. Using 3% Ti-doped $K(Ta,Nb)O_3\;targets,\;K(Ta,Nb)O_3$:Ti films were grown in MgO(001) crystals using pulsed laser deposition. First, growth conditions were optimized. A reduction in the loss tangent was observed for Ti-doped $K(Ta,Nb)O_3$ relative to undoped films, although a reduction in tunability is also seen. The crystallinity, morphology, and tunability of $K(Ta,Nb)O_3$:Ti films are reported.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.127-130
• /
• 2002

In this study, development of a new LTCC material using a non-glassy system was attempted with respect to reducing the fabrication process steps and cost down. Lowering the sintering temperature can be achieved by liquid phase sintering. For LTCC application, the starting material must have quality factor as high as possible in microwave frequency range. And also, the material should have a low dielectric constant for enhancing the signal propagation speed. Regarding these factors, dielectric constants of various materials were estimated by the Clausius-Mosotti equation. Among them, CaWO$_4$ was tamed out the suitable LTCC material. CaWO$_4$ can be sintered up to 98% of full density at 1200$^{\circ}C$ for 3 hours. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 10.15, 62880GHz, and -27.8ppm/$^{\circ}C$, respectively. In order to modify the dielectric properties and densification temperature, 0.5∼1.5 wt% LiF were added to CaWO$_4$. LiF addition reduced the sintering temperature/time down to 800$^{\circ}C$/10∼30min due to the reactive liquid phase sintering. Dielectric constant lowered from 10.15 to 9.38 and Q x fo increased up to 92000GHz with increasing LiF content.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.139-144
• /
• 2016

The dependence of the microwave dielectric properties of the glass-ceramic composite $0.9CaMgSi_2O_6-0.1MgSiO_3$ on the crystallization behaviour was investigated as functions of the $TiO_2$ content and heat-treatment temperature. The crystallization behaviour of the specimens was evaluated via a combination of the Rietveld and reference-intensity ratio methods. For specimens with a $TiO_2$ content of up to 1 wt.%, a monoclinic diopside phase was formed, whereas a secondary $TiO_2$ phase was formed with further increases in the $TiO_2$ content. The quality factor (Qf) of the specimens was strongly dependent on the degree of crystallization. The highest Qf value was obtained with a $TiO_2$ content of 0.5 wt.%, which was improved by increasing the heat-treatment temperature. The dielectric constant (K) was affected by the size of the crystallites and the $TiO_2$ content. The temperature coefficient of the resonant frequency (TCF) was nearly constant for all of the specimens, regardless of the $TiO_2$ content or heattreatment temperature.

• Journal of the Korean Ceramic Society
• /
• v.44 no.10
• /
• pp.537-541
• /
• 2007

Microwave dielectric properties of $0.95 Ca_{0.85}Nd_{0.1}TiO_3-0.05LnAlO_3$ (Ln=Sm, DH, Er) were investigated as a function of sintering temperature and lanthanide ion type. A single perovskite phase with an orthorhombic structure was obtained throughout the entire range of composition. The dielectric constant (K) was dependent upon the dielectric polarizabilities and the B-site bond valence in the $ABO_3$ perovskite structure. The quality factor (Qf) of the specimens with $ErAlO_3$ was smaller than those with $SmAlO_3\;and/or\;DyAlO_3$ due to the smaller grain size. The temperature coefficient of resonant frequency (TCF) could be controlled from $107.28ppm/^{\circ}C$ at Ln=Sm to $87.23ppm/^{\circ}C$ at Ln=Er due to the changes of B-site bond valence in the $ABO_3$ perovskite structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.299-299
• /
• 2010

In this study, microwave properties with compositions and frequency of the $Ba_3Co_2Fe_{24}O_{41}$ ceramics with Zn substitution for Co were investigated. From the XRD patterns, hexagonal structure of Z-type phase was existed as main phase. Diffraction peaks of Z-type phase were shifted to lower angle by Zn substituted for Co site. The permittivity was increased with Zn additions. In all composition, loss tangent of permittivities were increased with frequency. Permeability and magnetic resonance frequency were increased with Zn additions. Permeability was increased and loss tangent of permeability was decreased rapidly over 600 MHz~800 MHz. The loss tangent of permeability did not changed with composition ratio. In the case of $Ba_3Co_{1.6}Zn_{0.4}Fe_{24}O_{41}$ ceramics sintered at $1250^{\circ}C$ for 3 hours, the permittivity, loss tangent of permittivity, permeability and loss tangent of permeability were 28.277, 0.193, 22.992 and 0.065 at 310 MHz, respectively.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1043-1047
• /
• 1998

The effect of CuO and CdO addition on the microwave dielectric properties of $BiNbO_4$, ceramics were investigated. As the content of CdO increased, sintered density and quality factor decreased. With increasing sintering temperature, both the dielectric constant and quality factor increased. In the case of specimen sintered at $960^{\circ}C$ with addition of 0.03 wt% of CuO and CdO, respectively. the microwave dielectric properties obtained were dielectric constant of 41.2, quality factor ($Q{\times}f_0$) of 6,500 (at 5.6GHz), temperature coefficient of resonant frequency of $3ppm^{\circ}C$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.9
• /
• pp.459-463
• /
• 2004

In this study, the (l-x)$TiTe_3O_{8}$-x$MgTiO_3$ ceramics were investigated to obtain the improved dielectric properties of a high temperature stability and a sintering temperature of less than $900^{\circ}C$ which was necessary for the LTCC. According to the X-ray diffraction patterns of the (l-x)$TiTe_3O_{8}$-x$MgTiO_3$(x=0∼1) ceramics, the columbite structure of $TiTe_3O_{8}$ and ilmenite structure of $MgTiO_3$ were coexisted. Increasing the $MgTiO_3$ mole ratio(x), the density and dielectric constant were decreased and temperature coefficient of resonant frequency was moved to the negative direction and the quality factor was increased. In the case of the 0.6$TiTe_3O_{8}$-0.4$MgTiO_3$ ceramics sintered at $830^{\circ}C$ for 3hr., the microwave dielectric properties were $\varepsilon_{\gamma}$=29.3, Q${\times}$$f_{\gamma}$=39.600GHz and $\tau$$_{f}$=+9.3ppm/$^{\circ}C$.

• Transactions of Materials Processing
• /
• v.29 no.4
• /
• pp.179-187
• /
• 2020

Existing composite forming processes such as the autoclave, prepreg compression forming (PCF), RTM, etc. require high production costs because of their long processing time. On the other hand, microwave heating process (MHP) can reduce the production costs since both mold and composite material can be heated directly. The aim of this study is to manufacture a mold consisting of polytetrafluoroethylene (PTFE), quartz glass, stainless steel clamps, and polyether ether ketone (PEEK) bolts for fabricating FML based on self-reinforced polypropylene (SRPP) using the MHP. First, the flame test was carried out prior to the MHP to check the temperature on the mold and whether the spark occurred at the mold and the edge of the FML. Second, the uniaxial tensile test was then conducted to obtain the mechanical properties of the FML manufactured by the MHP. The mechanical properties were compared with those of the FML fabricated by the PCF. As a result, the MHP using the PTFE mold can manufacture the FML more rapidly than the PCF, and obtain acceptable mechanical properties.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1459-1461
• /
• 1997

The microwave dielectric ceramic properties of $CaTiO_3-(Li_{1/2}Nd_{1/2})TiO_3$ were investigated. The solid solution of $CaTiO_3-(Li_{1/2}Nd_{1/2})TiO_3$ had the perovskite structure in the range of all composition. The dielectric constant and temperature coefficient of resonant frequency of solid solution were decreased with the contend of $(Li_{1/2}Nd_{1/2})TiO_3$, whereas, the $Q{\times}f$ value was increased. In the $(1-X)CaTiO_3-X(Li_{1/2}Nd_{1/2})TiO_3$ system, the microwave properties could be controlled by the variation of X, X is weight fraction. Typical value of K=119, $Q{\times}f=2970$ and $TCF=14ppm/^{\circ}C$ were obtained for $0.2CaTiO_3-0.8(Li_{1/2}Nd_{1/2})TiO_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.342-342
• /
• 2008

The low temperature sintering and microwave dielectric properties of ceramic/glass composites which were composed of ceramics in the $Bi_2(Zn_{1/3}Nb_{2/3})_2O_7$ and zinc borosilicate glass/bismuth-zinc borosilicate glass were investigated with a view to applying the microwave dielectrics to low temperature co-fired ceramics. The $Bi_2(Zn_{1/3}Nb_{2/3})_2O_7$ addition of 5 wt% ZBS and BZBS glass ensured a successful sintering below $900^{\circ}C$. In addition, pyrochlore phase was observed in the all composition. $Bi_2(Zn_{1/3}Nb_{2/3})_2O_7$ with 5 wt% BZBS glasss demonstrated 70 as the dielectric constant ($\varepsilon_r$), 2,500 GHz as the Q$\times$f value, and -40 ppm/$^{\circ}C$ as TCF.