• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.540-544
• /
• 1996

To apply the CVD diamond film to coated tools, it is necessary to make adhesion strength between diamond film and substrate stronger. So adhesion strength of diamond coated WC-Co tools using Microwave Plasma CVD and cutting test of Al-18mass%Si alloy using diamond cutting tools were studied. Diamond coating was carried out using Microwave Plasma CVD apparatus. Reaction gas was used mixture of methane and hydrogen. Substrate temperature were varied from 673K to 1173K by control of microwave output power and reaction pressure. By observation of SEM, grain size became larger and larger as substrate temperature became higher and higher. Also all deposits were covered with clear diamond crystals. XRD results, the deposits were identified to cubic diamond. An analysis using Raman spectroscopy, the deposit synthesized at lower substrate temperature (673K) showed higher quality than deposit synthesized at higher substrate temperature (1173K). As a result of scratch adhesion strength test, from 873K to 1173K adhesion strength decreased by rising of substrate temperature. The deposit synthesized at 873K showed best adhesion strength. In the cutting test of Al-18mass%Si alloy using diamond coated tools and the surface machinability of Al-Si works turned with diamond coating tools which synthesized at 873K presented uniform roughness. Cutting performance of Al-18mass%Si alloys using diamond coated WC-Co tools related to the adhesion strength.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.842-848
• /
• 2008

In this study, we propose a novel micro-ion engine system. Single plasma source is used for both ion beam source and neutralizing electron source. By changing the electrical connection, either operation can be switched. This micro-ion engine system gives translation motion and attitude control to microspacecraft. The major objective of this study is verification of our concept. Small plasma source of 20 mm diameter was developed. Plasma was sustained by microwave power. Using this plasma source, ion beam extraction and electron emission was successively demonstrated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.699-704
• /
• 2003

The characteristics of microwave reflectometry as a non-invasive device to examine the density distribution of inhomogeneous media using the technology of FM radar is presented. The microwave reflectometry system requires an optimized system hardware and the understanding of system response from the density distribution in order to provide the system solution to describe the object under test quantitatively. Among the applications, the use of microwave reflectomeoy in the area of applied plasma physics has been newly proposed and the number of usage is found to be increasing gradually. The microwave reflectometry systems that depend on the nature of the object under test are described. The experimental method to characterize the system is explained and the experimental results on the wavenumber dependence and the sensitivity on density perturbation are presented as well as the comparison to the results from the one dimensional numerical simulations.

• Journal of the Korean Institute of Gas
• /
• v.2 no.3
• /
• pp.60-69
• /
• 1998

Methane, the major constituent of natural gas, had been converted to higher hydrocarbons by microwave and radio-frequency plasma in vacuum condition. Methane had been activated to plasma by suppling high energy then converted to ethane, ethylene, acetylene. The direct conversion process of methane had produced few by-products and demanded low-energy. The plasma sources were microwave and radio-frequency. Two types of reactor had been used to activate methane. One is common single tubular-type reactor and the other is series coil-type reactor which used for the first time in this study. To produce more C2 products, methane had been converted by a plasma and catalyst. The results of this study could be used to study mechanism of plasma reaction of methane, design the plant-scale reactor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.147-147
• /
• 2012

Cutoff probe has been used for measuring a plasma density using the cutoff peak which is located at the plasma frequency in the low pressure plasma. However, research on analysis of low frequency region of transmission microwave frequency (TMF) spectrum does not performed even though important plasma parameters are located in the low frequency region, i.e., ion plasma frequency and collision frequency. In this research, we analyzed the low frequency region of the TMF spectrum. Experimental results reveal the effect of plasma parameters on the low frequency region on the TMF spectrum. Based on the response of TMF spectrum from changing of plasma parameters, deduction of the plasma parameters was tried. This comprehensive analysis of TMF spectrum expands applicable area of cutoff probe.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.895-897
• /
• 1998

The optical spectra of microwave plasma by four kinds of gases($N_2$, $N_2-CH_4$, $H_{2}-CH_{4}$ and Air-$CH_4$) have been measured for investigating 388.4[nm] peak which has the same intensity as $H_{\alpha}$(656.4[nm]) peak. A 388.4[nm] peak by $N_2$ plasma, $N_{2}-CH_{4}$ plasma and Air-$CH_4$ plasma may be CN peak because it is with 337.1, 357.8 and 316.0[nm] peaks by $N_2$. And a 388.4[nm] peak by $H_{2}-CH_{4}$ plasma without by $N_2$ 337.1, 357.8 and 316.0[nm] peaks may be CH peak. In the investigation results for optical spectra by $H_{2}-CH_{4}$ plasma and $H_{2}-CH_{4}-O_{2}$ plasma, the density of hydrogen atom was increased because oxygen decompose hydrogen molecules in $H_{2}-CH_{4}$ plasma with oxygen. These hydrogen atom decompose $CH_4$ and increase CH radical. And the crystalline of deposited diamond was good and the growth rate increased.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.2
• /
• pp.53-57
• /
• 2009

In this paper we develop a method to observe faults in semiconductor devices and transmission lines by calculating the variation of the reflection function in a dielectric microstrip line that has an open-ended termination containing an optically induced plasma region. It is analyzed with the assumption that the plasma is distributed homogeneously in laser illumination. With the non linear material of degradation, the concentration of the carrier in the part of the material has changed. Since the input wave has produced the phenomenon of reflection, the input signal to the open-ended microstrip lines can be observed on reflection to identify the location of the fault. The characteristic impedances resulting from the presence of plasma are evaluated by the transmission line model. The variation of the reflection wave in the microwave system has been calculated by using an equivalent circuit model. The transient response has been also evaluated theoretically for changing the phase of the variation in the reflection. The variation of characteristic response in differentially localized has been also evaluated analytically.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.819-824
• /
• 2000

In this research, the etching characteristics of Ta thin film with chlorine plsama have been studied by Electron Cyclotron Resonance (ECR) plasma etching system. The effects of microwave power, RF bias power, working pressure and gas chemistry on the etching profiles have been investigated. The microloading effect, which was observed at fine pattern formation, was effectively suppressed by double step etching, and anisotropic $0.2{\mu\textrm{m}}$ L&S patterns were successfully generated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.699-706
• /
• 2018

The permeation properties of plasma polymer membranes were studied for permanent gases such as He, $H_2$, $O_2$, $N_2$, $CH_4$ and condensable vapors such as $CO_2$, $C_2H_4$, $C_3H_8$. The plasma polymers were prepared by the discharge of microwave or radiofrequency(RF) wave. Hexamethyldisiloxane (HMDS) vapor was used as a monomer for plasma polymerization. In HMDS plasma-polymerized membranes prepared under microwave discharge, the permeability coefficient was dependent of the kinetic molecular diameter of the permeate gases. Additionally the membranes showed higher $O_2/N_2$ permselectivity compared to the plasma polymers from radiofrequency discharge. On the contrary, in the HMDS plasma-polymerized membranes prepared under radiofrequency discharge, the permeability coefficient was dependent of the critical temperature of the permeant gases. The membranes showed high selectivities of $C_2H_4$ and $C_3H_8$ over $N_2$. The permeability coefficient of plasma polymerized membranes prepared under microwave discharge was dependent of the molecular diameter of permeant gases because of high crosslinking density of the membrane. However, the crosslinking density of the plasma polymerized membranes prepared under RF discharge was lower because the energy density of RF wave is weaker than that of microwave. Hence, the permeability of RF plasma polymerized membranes became dependent of the critical temperature rather than molecular diameter of the gases.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.5
• /
• pp.211-214
• /
• 2004

Carbon nanofiber bundles were formed on silicon substrate using microwave plasma-enhanced chemical vapor deposition system. These bundles were vertically well-grown under the high negative bias voltage condition. The bundles were composed of the individual carbon nanofiber having less than 100 nm diameters. Turn-on voltage of the field emission was measured around 0.8 V/$\mu\textrm{m}$. Fowler-Nordheim plot of the measured values confirmed the field emission characteristic of the measured current.