• Composites Research
• /
• 제32권1호
• /
• pp.37-44
• /
• 2019

스카프 접착 조인트를 마이크로 볼트로 보강하였을 때, 볼트의 보강효과를 얻을 수 있는지를 시험으로 연구하였다. 스카프 형상에 따른 조인트 보강효과를 확인하기 위해 3가지 스카프비(1/10, 1/20, 1/30)를 고려하였다. 접착면적에 따른 핀의 밀도를 동일하게 유지하기 위해, 1/10, 1/20, 1/30 스카프비를 가지는 조인트에 각각 16, 32, 48개의 볼트를 보강하였다. 기준값을 획득하기 위해 접착제로만 체결된 조인트와 마이크로 볼트만 사용한 조인트에 대한 시험도 수행하였다. 시험 결과 접착제만 적용한 경우, 각 스카프비(1/10, 1/20, 1/30)에 따른 파손하중은 29.7, 39.6, 44.8 kN로 나타났다. 마이크로 볼트로 보강한 경우 파손하중은 스카프비에 따라 각각 28.4, 37.2, 40.1 kN으로 나타났는데, 순수 접착 조인트 파손하중의 96, 94, 90%에 해당한다. 마이크로 볼트만 사용한 경우, 파손하중은 접착 조인트 인장강도의 13-25%에 불과하였다. 스카프비 1/10 조인트의 피로시험 결과 접착제와 볼트를 동시에 사용한 하이브리드 조인트의 피로강도가 접착제만 사용한 경우의 피로강도보다 증가하였지만, 증가율은 2-3%로 미미하였다. 본 연구를 통해 박리응력이 파손의 주원인이 되는 구조물에서와 달리, 전단응력이 파손의 주원인이 되는 스카프 조인트의 경우 마이크로 볼트의 보강효과는 나타나지 않는 것을 확인하였다.

• Smart Structures and Systems
• /
• 제29권3호
• /
• pp.445-455
• /
• 2022

Steel anchor bolts are installed in concrete using a variety of methods. One of the most common methods of anchor bolt installation is using epoxy resin as an infill material injected into the drilled hole to act as a bonding material between the steel bolt and the surrounding concrete. Typical design standards assume uniform stress distribution along the length of the anchor bolt accompanied with single crack leading to pull-out failure. Experimental evidence has shown that the steel anchor bolts fail owing to the multiple failure patterns, hence these design assumptions are not realistic. In this regard, the presented research work details the analytical model that takes into consideration multiple micro cracks in the infill material induced via impact loading. The impact loading from the Schmidt hammer is used to evaluate the bond condition bond condition of anchor bolt and the epoxy material. The added advantage of the presented analytical model is that it is able to take into account the various type of end conditions of the anchor bolts such as bent or U-shaped anchors. Through sensitivity analysis the optimum stiffness and shear strength properties of the epoxy infill material is achieved, which have shown to achieve lower displacement coupled with reduced damage to the surrounding concrete. The accuracy of the presented model is confirmed by comparing the simulated deformational responses with the experimental evidence. From the comparison it was found that the model was successful in simulating the experimental results. The proposed model can be adopted by professionals interested in predicting and controlling the deformational response of anchor bolts.

• 한국생산제조학회지
• /
• 제25권6호
• /
• pp.421-425
• /
• 2016

Micro-EDM is one of the recent fine-machining technologies. Micro-EDM is widely used in precision processes because products manufactured via EDM are free from workpiece hardness. However, the debris produced during the process cause many problems such as reduced precision of the process. The first solution of this problem involves using the milling hole process. Micro-EDM hole process involves an electrode moving rapidly in the vertical direction via a servo system to disperse debris. However, this process can cause reduced work efficiency owing to contact between the electrode and workpiece. In this study, ultrasonic vibration is added to micro-EDM channel machining. Ultrasonic vibration removes the debris during machining and enables precision machining. Consequently, a clean work environment for the subsequent processes is maintained.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.132-136
• /
• 2009

The importance and interests for saving of energy and cost in industry has been steadily grown up. Therefore, process optimization to reduce the processing step and energy is one of the most important things. The micro-alloyed steel of which post-heat-treatment is not necessary, has attractive points for high strength materials. However, for the application of non-heat-treated steel to structural parts, it is necessary to confirm the reliability of mechanical properties. In order to estimate mechanical properties. The microstructure, hardness, tensile strength, compressive strength and tensile fatigue strength of micro-alloyed steel having 900MPa tensile strength has been investigated.

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.108-116
• /
• 2007

To overcome many defects such as the high product cost, large energy consumption, and big space capacity in conventional mechanical machining, the miniaturization of machine tool and micro factory systems has been envisioned recently. The object of this paper is to research the effect of dynamic characteristic parameters in bolted-joint beams, which is widely applied to the joining of mechanical structures in order to identify structural system characteristics and to predict dynamic behavior according to scale-down from macro to micro system as the development of micro/meso-scale machine tool and micro factories. Modal parameters such as the natural frequency, damping ratio, and mode shape from modal testing and dynamic characteristics from finite element analysis are extracted with all 12 test beam models by materials, by size, and by joining condition, and then the results obtained by both methods are compared.

• 한국지진공학회논문집
• /
• 제17권5호
• /
• pp.227-235
• /
• 2013

Friction energy dissipative devices have been increasingly implemented as structural seismic damage protecting systems due to their excellent seismic energy dissipating capacity and high stiffness. This study develops rotational friction energy dissipative devices and verifies experimentally their cyclic response. Based on the understanding of the differences between the traditional linear-motion friction behavior and the rotational friction behavior, the configuration of the frictional surface was determined by investigating the characteristics of the micro-friction behavior. The friction surface suggested in this paper consists of brake-lining pads and stainless steel sheets and is normally stressed by high-strength bolts. Based upon these frictional characteristics of the selected interface, the rotational friction energy dissipative devices were developed. Bolt torque-bearing force tests, rotational friction tests of the suggested friction interfaces were carried out to identify their frictional behavior. Test results show that the bearing force is almost linearly proportional to the applied bolt torque and presents stable cyclic response regardless of the experimental parameters selected this testing program. Finally, cyclic tests of the rotational friction energy dissipative devices were performed to find out their structural characteristics and to confirm their stable cyclic response. The developed friction energy dissipative devices present very stable cyclic response and meet the requirements for displacement-dependent energy dissipative devices prescribed in ASCE/SEI 7-10.

• 한국수산과학회지
• /
• 제35권3호
• /
• pp.282-288
• /
• 2002

전복 방류효과조사를 위한 효과적인 표지 개발을 위하여 치패에 알맞은 표지 탐색과 표지에 따른 성장과 생존율에 관하여 2000년 5월 25일부터 2001년 1월 27일까지 8개월간 조사하였다. 실험군 (결각군, 동선부착군, 볼트너트구조물부착군 그리고 너트접착군)별 표지부착률은 각장 2, 3cm 볼트너트부착군에서 89.9, $89.5\%$로 가장 높았고, 결각군이 $18.5\%$ 이하로 가장 낮게 식별되었다. 패각 내부에서 표지를 피복하여 표지의 안정성을 높이는 표지피복률은 각장 2, 3cm 볼트너트부착군은 각각 $100.0\%$, $96.6\%$로 나타난 반면, 동선부착군에서는 $17.1\%$ 이하로 나타났다. 각장 2, 3, 4와 5cm의 치패 크기에 따른 표지 실험군별 성장은 대조군와 유의한 차이를 보이지 않아 표지가 전복치패의 성장에 영향을 미치지 않았다. 생존율 역시 각장 2, 3, 4cm의 모든 실험군에서 $93.8\%$ 이상을 보였고, 대조군에 비해 유의한 차이를 보이지 않아 표지가 전복의 폐사에 미치는 영향은 없었다. 각장 5cm 실험군의 생존율은 대조군에 비해 각 실험구는 유의한 차이를 보였다. 이상의 결과에서 표지부착 및 피복률, 성장과 생존 등에서 우수한 결과를 보인 미세볼트너트표지를 부착한 각장 3cm실험군이 본 연구에서 가장 우수한 효과를 보였다.

• 한국산학기술학회논문지
• /
• 제15권4호
• /
• pp.1879-1884
• /
• 2014

최근 미세접합 기술이 다양한 사회에서 주목받고 있다. 미세접합 기술은 레이저 접합 초음파 접합 등이 있다. 그러나 미세 접합의 연구가 많이 부족한 실정이다. 이에 본 논문에서는 초음파 접합장치 구동 시 열평형 상태에서 압전소자에 열영향을 최소화하기 위해 냉각관을 설계하였다. 또한 냉각관이 설계된 초음파 접합 장치를 이용하여 접합 실험을 실시하였다. 다꾸찌 실험계획법을 이용하여 실험을 실시하였으며, 기초실험을 통해 공정변수와 반응 변수를 설정하였다. 접합 실험의 신뢰도를 검증하기 위하여 접합 계면의 미세조직을 관찰하였고, 인장실험을 통해 접합 강도를 확인하였다.

• Structural Engineering and Mechanics
• /
• 제72권5호
• /
• pp.557-568
• /
• 2019

Accurate modeling of contact interface in bolted joints is crucial in predicting the dynamic behavior for bolted assemblies under external load. This paper presents a contact pressure distribution based non-uniform virtual material method to describe the joint interface of assembly structure, which is connected by sparsely distributed multi-bolts. Firstly, the contact pressure distribution of bolted joints is obtained by the nonlinear static analysis in the finite element software ANSYS. The contact surface around bolt hole is divided into several sub-layers, and contact pressure in each sub-layer is thought to be evenly. Then, considering multi-asperity contact at the micro perspective, the relationship between contact pressure and interfacial virtual material parameters for each sub-layer is established by using the fractal contact theory. Finally, an experimental platform for the dynamic characteristics testing of a beam lap structure with double-bolted joint is constructed to validate the efficiency of proposed method. It is found that the theoretical results are in good agreement with experimental results by impact response in both time- and frequency-domain, and the relative errors of the first four natural frequencies are less than 1%. Furthermore, the presented model is used to examine the effect of rough contact surface on dynamic characteristics of bolted joint.

• Tribology and Lubricants
• /
• 제25권4호
• /
• pp.256-260
• /
• 2009

Fretting is a kind of wear which effects on reliability and durability. When machine parts are joined joint in parts such as a bolt or a rivet or a pin, fretting phenomenon is occurred by micro relative movement. When fretting occurs in joint parts, there is wear which is the cause of fatigue crack. Recently, although the ways of assessment of fatigue and damage tolerance are established, there is no way to evaluate fatigue crack initiation life by fretting phenomenon. Consequently, the prediction of life and prevention plan caused by fretting are needed to improve reliability. The objective of this paper is to predict fretting wear by using a experimental method and contact analysis considering wear process. For prediction of fretting wear volume, systematic and controlled experiments with a disc-plate contact under gross slip fretting conditions were carried out. A modified Archard equation is used to calculate wear depths from the contact pressure and stroke using wear coefficients obtained from the disc-plate fretting tests.