• 전기학회논문지
• /
• 제59권4호
• /
• pp.707-714
• /
• 2010

When problems such as line fault, breakdown of a substation or a generator, etc. arise on the grid, the Microgrid is designed to be separated or isolated from the grid. Most existing DGs(Distributed Generators) in distribution system use rotating machine. However, new DGs such as micro gas turbine, fuel cell, photo voltaic, wind turbine, etc. will be interfaced with the Microgrid through an inverter. So the Microgrid may have very lower inertia than the conventional distribution system. By the way, the rate of change of frequency depends on the inertia of the power system. Moreover, frequency has a strong coupling with active power in power system. Because the frequency of the Microgrid may change rapidly and largely during transient, appropriate and fast control strategy is needed for stable operation of the Microgrid. Therefore, this paper presents a power balancing strategy in Microgrid during transient. Despite of strong power or frequency excursions, power balancing in the Microgrid can be maintained.

• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.101-112
• /
• 2015

Renewable energy resources play an important part in the world's future. Renewable energy sources have the following components: biomass, geothermal, solar thermal, directs solar, wind, tidal and hydropower. Hydropower is still the most efficient way to generate electricity worldwide. Hydropower projects can contribute as a cheap energy source, as well to encourage the development of small industries across a wide range of new technology; furthermore hydropower systems use the energy in flowing and falling water to produce electricity or mechanical energy. Hydropower systems are classified as large, medium, small, mini and micro according to their installed power generation capacity, as do the following components: water turbines, control mechanisms and electrical transmissions. In this article a review of small hydropower systems has been done on the principles surrounding the fundamentals of hydraulic engineering, the fundamentals of hydrology, identification of sites and economic analysis.

• 조명전기설비학회논문지
• /
• 제24권8호
• /
• pp.40-47
• /
• 2010

Micro Grid(MG)는 새로운 개념의 전력시스템으로 Smart Grid 기술의 일환으로 관심을 받고 있다. 기본적인 MG의 개념은 신/재생에너지를 포함한 분산전원의 도입 및 효율적인 계통운영이지만 여기에는 전력공급의 신뢰성과 경제성이 배제될 수 없는 요소임은 확실하다. MG라는 새로운 계통의 개념을 도입하는데 있어서 기존 전력계통(Utility Grid)과의 간섭, 신뢰도 및 전력품질의 문제들이 해결해야 하는 숙제로 떠오르고 있는데 이에 대한 대안 중 하나가 에너지저장기술이다. 그러나 본 기술은 아직까지는 초기투자비 및 운영유지비가 매우 높은 수준이기 때문에 MG의 설계에 있어서 신뢰도와 경제성을 함께 고려한 Energy Storage System(ESS)의 설치방법이 필요로 된다. 이에 본 논문에서는 공급신뢰도기준을 충족할 수 있는 ESS의 최소필요용량 및 적정투자시점을 결정하는 확률론적 방법을 제안하고 이에 대한 사례연구를 수행하였다.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.513-520
• /
• 2018

Since Paris Climate Change Conference in 2015, many policies to reduce the emission of greenhouse gas have been accelerating, which are mainly related to renewable energy resources and micro-grid. Presently, the technology development and demonstration projects are mostly focused on diversifying the power resources by adding wind turbine, photo-voltaic and battery storage system in the island-type small micro-grid. It is expected that the large-scaled micro-grid projects based on the regional district and town/complex city, e.g. the block type micro-grid project in Daegu national industrial complex will proceed in the near future. In this case, the economic cost or the carbon emission can be optimized by the efficient operation of energy mix and the appropriate construction of electric and heat supplying facilities such as cogeneration, renewable energy resources, BESS, thermal storage and the existing heat and electricity supplying networks. However, when planning a large residential town or city, the concrete plan of the energy infrastructure has not been established until the construction plan stage and provided by the individual energy suppliers of water, heat, electricity and gas. So, it is difficult to build the efficient energy portfolio considering the characteristics of town or city. This paper introduces an energy mix optimization(EMO) method to determine the optimal capacity of thermal and electric resources which can be applied in the design stage of the real large-scaled residential town or city, and examines the feasibility of the proposed method by applying the real heat and electricity demand data of large-scale residential towns with thousands of households and by comparing the result of HOMER simulation developed by National Renewable Energy Laboratory(NREL).

• KIEE International Transactions on Power Engineering
• /
• 제3A권1호
• /
• pp.27-34
• /
• 2003

In this paper, the power conditioner composed of the stand-alone single-phase squirrel cage rotor type self-excited induction generator (SEIG) driven by prime movers such as a wind turbine and a micro gas turbine (MGT) is presented by using the steady-state circuit analysis based on the two nodal admittance approaches using the per-unit frequency in addition to a new state variable defined by the per-unit slip frequency along with its performance evaluations for the stand-alone energy utilizations. The stande-alone single-phase SEIG operating performances in unregulated voltage control loop are then evaluated on line under the conditions of the speed change transients of the prime mover and the stand-alone electrical passive load power variations with the simple theoretical analysis and the efficient computation processing procedures described in the part I of this paper. In addition, a feasuible PI controlled feedback closed-loop voltage regulation scheme of the stande-alone single-phase SEIG is designed on the basis of the static VAR compensate. (SVC) and discussed in experiment for the promising stand-alone power conditioner. The experimental operating performance results are illustrated and give good agreements with the simulation ones. The simulation and experimental results of the stand-alone single-phase SEIG with the simple SVC controller for its stabilized voltage regulation prove the practical effectiveness of the additional SVC control loop scheme including the PI controller with fast response characteristics and steady-sate performance improvements.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.70-75
• /
• 2011

Nowadays, modern gearboxes are characterized by high torque load demands, low running noise and compact design. Also durability of gearbox is specially a major issue for the industry. For the gearbox which used in wind turbine, gear transmission error(T.E.) is the excitation that leads the tonal noise known as gear whine, and radiated gear whine is also the dominant source of noise in the whole gearbox. In this paper, tooth modification for the high speed stage is used to compensate for the deformation of the teeth due to load and to ensure a proper meshing to achieve an optimized tooth contact pattern. The gearbox is firstly modeled in Romax software, and then the various combination analysis of the tooth modification is presented by using Windows LDP software, and the prediction of transmission error under the loaded torque for the helical gear pair is investigated, the transmission error, contact stress, root stress and load distribution are also calculated and compared before and after tooth modification under one torque condition. The simulation result shows that the transmission error and stress under the loads can be minimized by the appropriate tooth modification.

• 한국태양에너지학회 논문집
• /
• 제39권6호
• /
• pp.93-112
• /
• 2019

In this paper, a very new web-based software for renewable energy system (RES) design and economic evaluation was introduced. This solution would provide the precise RES estimation service including not only photovoltaic (PV), wind turbine (WT) and fuel cell (FC) individually but also energy storage system (ESS) as combined forms with PV or WT. The three reasons why we ought to develop it are: First, the standardized tool suitable to the domestic environment for estimating power generation from RES facilities and economic evaluation is required. Secondly, the standardized tool is needed to spread domestic RES supply policy and to promote the new industry in the micro-grid field. The last, the reliability of economic evaluation should be enhanced more for new facilities. To achieve those aims, the weather database of one hundred locations have established and the RES facility database has also constructed. For the energy management, mathematical models for PV, WT, ESS and FC were developed. As a final phase, the analytical process to evaluate economics has performed with field data verification.

• 전기학회논문지
• /
• 제65권2호
• /
• pp.239-246
• /
• 2016

In recent years, the power demand has been increasing steadily and the occurrence of maximum power demand has been moving from the summer season to the winter season in Korea. And since the control of electric power supply and demand is more important under those situations, a micro-grid system began to emerge as a keyword for the sTable operation of electric power system. A micro-gird power system is composed of various kinds of distributed generators(DG) such as small diesel generator, wind turbine, photo-voltaic generator and energy storage system(ESS). This paper introduces a method to determine the optimal capacities of the distributed generators which are installed in a stand-alone type of microgrid power system based on the fundamental proportion of diesel generator. At first, the fundamental proportion of diesel generator will be determined by changing from 0 to 50 percent. And then we will optimize the capacities of renewable energy resources and ESS according to load patterns. Lastly, after recalculating the capacity of ESS with consideration for SOC constraints, the optimal capacities of distributed generators will be decided.

• 한국전자통신학회논문지
• /
• 제9권4호
• /
• pp.527-536
• /
• 2014

본 논문에서는 마이크로그리드 적용을 위한 50kW 풍력발전기를 설계하였으며, 발전기의 해석은 maxwell 2D 상용프로그램을 사용하였다. 특히 제안된 PMSG는 코깅토크를 줄이고자 offset과 skew를 적용하였다. 최적의 옵셋과 스큐는 2mm와 전기각 60도를 제안하였다. 부하운전시 모의결과는 평균 고조파 1.3%, 전압 322.41V, 전류 94.95A, 철손 9.73W, 와류손 73.68W, 동손 3.52kW로 나타났다. 계산된 발전기 용량은 61.56kW이며, 제안된 설계절차는 더 큰 용량의 발전기설계에 적용할 수 있다.