• 한국농공학회논문집
• /
• 제60권2호
• /
• pp.25-36
• /
• 2018

Drip irrigation system is a low energy cost method which can efficiently save and supply water by dropping water slowly on the crop's root zone during crop growth. In the drip irrigation system, disk filters take an important role to physically remove impurity (inorganic and suspended organic) particles present in agricultural water which can cause emitter clogging. For the purpose, both top-and-bottom surfaces of the disk are grooved in micron size flowing from outside to inside. However, many congested flow paths in disk filter media incur higher head loss of inflow water resulting in relatively decreasing velocities depending on operation time than sand and mesh filters. Therefore, it is important to optimize the structure of disk filter in micro irrigation system. The head loss of disk filter media takes also charge of more than 60 % of total head loss in whole disk filter. This study is to find the appropriate cross-sectional shape of the disk groove to minimize the head loss by executing the experiment. The experiment used three disk filters that have similar filter body but have a half-elliptic and two kinds of triangular cross sections. The experimental results showed that the disk filter with half-elliptic cross sections of disk grooves have less head loss than the disk filter with regular triangular one.

• Journal of Biosystems Engineering
• /
• 제41권2호
• /
• pp.138-144
• /
• 2016

Purpose: Phosphorus is an essential element for water quality control. Excessive amounts of phosphorus causes algal bloom in water, which leads to eutrophication and a decline in water quality. It is necessary to maintain the optimum amount of phosphorus present. During the last decades, various studies have been conducted to determine phosphorus content in water. In this study, we present a comprehensive overview of colorimetric, electrochemical, fluorescence, microfluidic, and remote sensing technologies for the measurement of phosphorus in water, along with their working principles and limitations. Results: The colorimetric techniques determine the concentration of phosphorus through the use of color-generating reagents. This is specific to a single chemical species and inexpensive to use. The electrochemical techniques operate by using a reaction of the analyte of interest to generate an electrical signal that is proportional to the sample analyte concentration. They show a good linear output, good repeatability, and a high detection capacity. The fluorescence technique is a kind of spectroscopic analysis method. The particles in the sample are excited by irradiation at a specific wavelength, emitting radiation of a different wavelength. It is possible to use this for quantitative and qualitative analysis of the target analyte. The microfluidic techniques incorporate several features to control chemical reactions in a micro device of low sample volume and reagent consumption. They are cheap and rapid methods for the detection of phosphorus in water. The remote sensing technique analyzes the sample for the target analyte using an optical technique, but without direct contact. It can cover a wider area than the other techniques mentioned in this review. Conclusion: It is concluded that the sensing technologies reviewed in this study are promising for rapid detection of phosphorus in water. The measurement range and sensitivity of the sensors have been greatly improved recently.

• 대한환경공학회지
• /
• 제36권7호
• /
• pp.476-482
• /
• 2014

본 연구는 에멀젼 연료의 특성과 배출가스에 관하여 연구하였다. 엔진 배출가스 측정은 엔진 dinamometer로 실시하였다. 유화연료는 연소실내에서 미세폭발을 일으켜 연료를 잘게 쪼개어 주어 smoke를 감소시킨다. 그리고 물이 연소실내의 기화열을 빼앗아 연소실 내부의 온도를 낮추어 NOx 생성을 억제하는 효과를 갖는다. ND-13모드의 각 모드별 배출가스온도가 MDO에 비해 유화연료를 사용했을 때 낮게 나온 것으로 뒷받침 될 수 있었다. 유화연료의 함수율이 증가함에 따라 NOx와 smoke의 배출량은 줄어들었으며, 출력도 함수율 증가에 따라 유화연료 자체의 발열량 감소로 인하여 줄어든 것으로 판단된다. ND-13모드에서 MDO 유화연료를 시험결과 함수율 17% 유화연료의 NOx 감소량은 약 24%, smoke의 총감소량은 약 73%, $SO_2$ 감소량은 약 11%, 그리고 약 13%의 출력손실을 확인하였다.

• 한국진공학회지
• /
• 제21권5호
• /
• pp.225-232
• /
• 2012

수명 측정법과 동시 계수 도플러 넓어짐 양전자 소멸 분광법으로 p형과 n형 실리콘 시료에 3.98 MeV 에너지를 가진 $0.0{\sim}20.0{\times}10^{13}\;protons/cm^2$ 양성자 빔 조사에 의한 결함을 측정하여 실리콘 결함 특성에 대하여 조사하였다. 양전자와 전자의 쌍소멸로 발생하는 감마선 스펙트럼의 전자 밀도 에너지를 수리적 해석 방법인 S-변수와 열린 부피 결함에 대한 측정법으로서 양전자 수명 ${\tau}_1$과 ${\tau}_2$, 이에 따른 밀도 $I_1$과 $I_2$를 사용하여, 시료의 구조 변화를 측정하였다. 본 연구에서 측정된 S-변수와 양전자 수명은 시료에 조사된 양성자 조사량의 변화에 따라 결함이 증가하였으며, 양전자 수명 측정과 같은 경향을 보여준다. SRIM의 결과로써, 양성자 조사 에너지에 따른 Bragg 피크 때문에 양성자는 시료의 특정 깊이에 주로 결함을 형성하여 시료 전체에는 결함으로 잘 나타나지 않기 때문이다. 빔의 조사량에 따른 결함의 영향이 더 큰 것으로 나타났다.

• 한국세라믹학회지
• /
• 제34권2호
• /
• pp.195-201
• /
• 1997

본 논문은 kaolinite(Al2O3.2SiO2.2H2O)-aluminum trihydroxide(Al(OH3) 혼합물을 소결전에 planetary ball mill을 사용하여 건식 중에서 혼합분쇄한 후, 이 혼합물을 사용하여 소결하는 동안에 mullite의 생성거동을 연구한 것이다. 혼합물의 입자크기 감소는 분쇄 초기에 현저하였으며, 분쇄기간이 증가함에 따라 미립자들이 응집하는 현상을 보였다. 혼합물의 결정구조는 planetary ball milling에 의한 혼합분쇄에 따라 쉽게 비정질화되었으며, 비정질화되는 정도는 분쇄시간이 증가함에 따라 증가하였다. Kaolinite의 초기 분순물로 존재했던 anatase를 제외한 mullite상만이 상대적으로 낮은 소결온도인 1523K에서 혼합분쇄한 혼합물의 소결체에서 나타났다. 한편, 분쇄하지 않은 혼합물의 소결체의 경우는 이 온도에서 mullite 상 이외에 corundum, cristobalite, Al-Si spinel상이 공존하는 형태로 나타났다. 따라서, 혼합분쇄처리는 출발원료의 미소 규모에 있어서 균일혼합 및 분산을 촉진시키며, 또한 결정구조변화에 따른 열분해온도의 변화일으켜, 상대적으로 낮은 온도에서 고순도의 mullite를 직접 생성하는데 효과적이였다.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3474-3490
• /
• 1996

A metal matrix composites(MMCs) for A16061 reinforced with silicon carbide particles is fabricated by melt-stirring method. The primary products of MMCs billets are prepared by volume fractions 5 vol% to 20 vol% and particle size $13\mu m$ to $22\mu m$.This paper will be made to examine the microstructure and mechanical properties of fabricated $SiC_p$/Al 6061 composite by melt-stirring and squeeze casting method. The MMC billets is extruded at $500^{\circ}C$ under the constant extrusion velocity $V_e$=2mm/min using curved shape die. Extrusion force, particle rearrangement, micro structure and mechanical properties of extruded composites will be investigated. The mechanical properties of primary billets manufactured by melt-stirring and squeeze casting method will be compared with extrusion specimen. The effect of volume fraction and size of the reinforcements will be studied. The increase in uniformity of particle dispersion is the major reason for an improvement in reliability due to hot extrusion with optimal shape die. Experimental Young's modulus and 0.2% offset yield strength for the extruded MMCs will be compared with theretical values calculated by the Eshelby method. A method will be proposed for the prediction of Young's modulus and yield strength in $SiC_p$ reinforced MMCs.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.165-173
• /
• 2005

This paper presents the results for deposition of micrometer-scale metal lines on glass for the development of TFT-LCD circuit repair-system. Although there had been a few studies in the late 1980's for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and W(CO)s was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 m depending on laser power and scan speed while the width was controlled between 50um using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below $1{\Omega}{\cdotu}um$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• 대한치과보철학회지
• /
• 제27권2호
• /
• pp.219-248
• /
• 1989

The purposes of this study were to analyze the microstructural and compositional changes of metal surfaces following different conditions of preoxidizing heat treatment, to investigate the composition of metal oxides, and to evaluate the effect of preoxidation and removal of surface oxides on microstructure and diffusion profiles. The techniques of EDAX (energy-dispersive analysis of x-ray), ESCA (electron spectroscopy for chemical analysis), and EPMA (electron probe micro analysis) were used, along with SEM (scanning electron microscopy). The obtained results were as follows : 1. A surface of the specimen became rough and the amount of the metal oxides increased with increasing the heat treatment time and temperature and the partial pressure of oxygen. 2. At an air pressure of 28' vacuum, the higher the temperature and the longer the time of preoxidation, the higher Ni concentration was detected. 3. Cr concentration in the specimen heat treated with air was higher than that of with vacuum. 4. The oxides in the specimens were mainly composed of Ni and Cr oxides. On the globular growth particles, significant rises in Al concentration of Rexillium III and Ti concentration of Verabond were noted. 5. Atomic diffusion occurred at the ceramic-metal interface, furthermore the amount of the flux was increased with preoxidation heat treatment.

• 대한기계학회논문집A
• /
• 제40권10호
• /
• pp.865-871
• /
• 2016

조직 공학에서는 전통적인 인공지지체 제작 방식인 가스 발포, 염 침출, 스폰지 복제 그리고 동결주조 법 등이 이용되고 있다. 하지만 다양한 공극 형태 및 크기를 가지고 있어서 세포 상호 작용 효과 및 충분한 기계적 특성에 한계가 있다. 그러나 열 용해 적층 법은 조직공학에서 폴리머 재료를 이용하여 다양한 3차원 인공지지체를 제작할 수 있는 가장 적절한 기술이다. 따라서 본 연구에서는 PCL 몰드를 제작하고 실리카와 알긴산 나트륨 염을 포함하는 세라믹 슬러리를 제조하여 몰드에 주입시켰으며, 1일 동안 자연 건조를 시켰다. 제작된 3차원 슬러리 몰드는 PCL 몰드의 제거 및 슬러리를 경화시키기 위해 $100^{\circ}C$의 오븐에서 2시간 열처리 되었고, 열처리 후에 $1100^{\circ}C$에서 소결되었다. 제작된 인공지지체는 주사전자현미경을 통해 관찰되었고, 압축 시험을 통해 알긴산 나트륨 염의 혼합량에 따른 인공지지체의 기계적 특성은 평가되었다.

• 대한치과보철학회지
• /
• 제43권4호
• /
• pp.415-425
• /
• 2005

Statement of problem : Fracture of composite resin core will be occulted by progress of crack. Bonding interface of different materials has large possibility of starting point of crack line. Therefore, the bond strength of glass fiber post to composite resin core is important for prevention of fracture. Purpose: This in vitro study tried to find out how to get the higher strength of glass fiber post to composite resin core through surveying the maximum load that fractures the post and cote complex. Materials and methods: 40 specimens made with glass fiber Posts(Style $post^{(R)}$, Metalor, Swiss) and composite resin core ($Z-100^{(R)}$, 3M, USA) were prepared and loaded to failure with push-out type shear-bond strength test in a universal test machine. The maximum fracture load and fracture mode were investigated in the specimens that were restored with four different surface treatments. With the data. ANOVA test was used to validate the significance between the test groups, and Bonferroni method was used to check if there is any significant statistical difference between each test group. Evely analysis was approved with 95% reliance. Results: On measuring the maximum fracture load of specimens, both the treatments of sandblasted and acid-etched one statistically showed the strength increase rather than the control group (p<0.005). The scanning electric microscope revealed that sand blasting made more micro-retention form not only on the resin matrix but on the glass fiber, and acid-etching contributed to increase in surface retention form, eliminated the inorganic particles in resin matrix. Specimen fracture modes investigation represented that sand blasted groups showed lower bonding failure than no-sand blasted groups. Conclusion: Referring to the values of maximum fracture load of specimens, the bonding strength was increased by sand blasting and acid-etching.