• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.1852-1853
• /
• 2006

This paper describes the development of temperature controller using program control method for small heating system. This system consists of three parts; sensing part, control part that includes the PID control algorithm, and actuating part. We introduce a zero-crossing control method of TRIAC and firmware technique using single chip micro-controller(ATmega8535) in the control part.

• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.305-310
• /
• 2009

Laser surface texturing (LST) methods are applied recently to generate micro-dimples in machine components having parallel sliding surfaces such as thrust bearings, mechanical face seals and piston rings, etc. And it is experimentally reported by several researchers that the micro-dimpled bearing surfaces can reduce friction force. Until now, however, theoretical results for various dimple parameters are not fully presented. In this paper, a commercial computational fluid dynamics (CFD) code, FLUENT is used to investigate the effect of dimple depth on the lubrication characteristics of parallel thrust bearing. The results show that the pressure, velocity and density distributions within dimples are highly affected by dimple depths and cavitation conditions. Adoption of micro-dimple on the bearing surface can reduce the friction force highly and its levels are affected by dimple depth. The numerical methods and results can be use in design of optimum dimple characteristics to improve thrust bearing performance.

• 동력기계공학회지
• /
• 제21권3호
• /
• pp.37-44
• /
• 2017

In this study, failure analysis of the angular pin for molding machines to aluminum component molding was carried out. SM45C steel was used for the angular pin, it was surface hardened by the induction surface hardening heat treatment. The cross section of damaged angular pin was observed, and micro Vickers hardness value from the fractured part was measured. Brittle fracture was occurred from the fracture surface of angular pin, therefore, impact toughness value was evaluated by V-notch Charpy impact test. It was confirmed that the impact absorption energy was high when was tempered at a high temperature for a long time, and the toughness was slightly increased. Also, 2-parameter Weibull statistical analysis was investigated in order to evaluate the reliability of the measured micro Vickers hardness values and absorbed energy. The micro Vickers hardness and absorbed energy well followed a two-parameter Weibull probability distribution, respectively. The reverse design against angular pin was proposed as possible by using test results.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1277-1280
• /
• 2005

A high-aspect-ratio and high-resolution stainless steel shadow mask for organic thin-film transistors (OTFTs) circuit has been fabricated by a new method which combines photochemical machining, micro-electrical discharge machining (micro-EDM), and electrochemical etching (ECE). First, connection lines and source-drain holes are roughly machined by photochemical etching, and then the part of source and drain holes is finished by the combination of micro-EDM and ECE processes. Using this method a $100\;\mu{m}$ thick stainless steel (AISI 304) shadow mask for inverter can be fabricated with the channel length of $30\;\mu{m}\;and\;10\;\mu{m}\;respectively.\;The\;width\;of\;connection line\;is\;150\;\mu{m}$. The aspect ratio of the wall is about 5 and 15, respectively. Metal lines and source-drain electrodes of OTFTs were successfully deposited through the fabricated shadow mask.

• 펄프종이기술
• /
• 제41권5호
• /
• pp.26-32
• /
• 2009

As a part of utilizing the nanocellulose (NC) from lignocellulosic components of wood biomass, this paper reports preliminary results on the products of sulfuric acid hydrolysis. The purpose of this study was to investigate the morphology of both NC and micro-sized cellulose fiber (MCF) isolated by acid hydrolysis from commercial microcrystalline cellulose (MCC). Field emission.scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) were employed to observe the acid hydrolysis suspension, NC, and MCF. The electron microscopy observations showed that the acid hydrolysis suspension, before separation into NC and MCF by centrifugation, was composed of nano-sized NCs and micro-sized MCFs. The morphology of isolated NCs was a whisker form of rod-like NCs. Measurements of individual NCs using TEM indicated dimensions of 6.96$\pm$0.87 nm wide by 178$\pm$55 nm long. Observations of the MCFs showed that most of the MCC particles had de-fibered into relatively long fibers with a diameter of 3-9 ${\mu}m$, depending on the degree of acid hydrolysis. These results suggest that proper technologies are required to effectively realize the potentials of both NCs and MCFs.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2001년도 제23회 KOSCO SYMPOSIUM 논문집
• /
• pp.57-62
• /
• 2001

The effect of micro scale turbulence on flame structure and stability were experimentally investigated by changing the area of micro turbulence generator(MTG) and air velocity in terms of low NOx and high efficiency combustion. NOx and CO concentration were also measured for different MTG areas to investigate whether a vane swirler having MTG has a possibility of using as part for low NOx combustor. From the obtained results, it is shown that flame stability region increases and flame size becomes small as MTG area increases since MTG in itself makes small scale recirculation flow and swirler does large scale recirculation one. It is also shown that low NOx concentration(about 20${\sim}$30ppm@$O_2$ 11%) is achieved for all MTG areas without any increase in CO concentration regardless of air velocity range tested in this study when the equivalence ratio is 0.7. The results obtained in this study can give basic guideline for the design of compact low NOx high efficiency combustor using a vane swirler having MTG.

• 정보교육학회논문지
• /
• 제22권2호
• /
• pp.231-238
• /
• 2018

소프트웨어 교육이 교육 현장에서 다루어지기 시작했지만 현장 교사가 활용할 수 있는 피지컬 컴퓨팅 교구 및 수업 가이드라인이 부족한 실정이다. 따라서 본 연구에서는 마이크로비트라는 피지컬 컴퓨팅 교구를 활용한 창의 컴퓨팅 교육 프로그램을 제시하였다. 교육 프로그램에 적용된 동시따응발(MDIAP) 교수학습모형은 동기 유발, 시연하기, 따라하기, 응용하기, 발표하기의 5단계로 구성되었다. 교수-학습 과정은 마이크로비트의 기본 센서와 추가적인 센서, 구동장치를 활용한 메이커 학습으로 구성하여 나선형으로 제시하였다. 이러한 일련의 교수 학습 활동을 통하여 학생들의 창의 컴퓨팅 사고력을 키울 수 있을 것으로 기대한다.

• 항공우주기술
• /
• 제3권2호
• /
• pp.25-33
• /
• 2004

본 논문에서는 인공위성 반작용휠의 미소진동 측정을 위한 테스트 장비와 이를 이용하여 실측한 반작용휠의 미소진동을 측정 및 분석 결과를 소개한다. 위성의 미소진동은 KISTLER dynamic platform 이라는 400Hz 이내의 3축의 힘과 3축의 토크를 동시에 측정할 수 있는 장비에 의해 측정되며 측정된 데이터는 회전 속도에 따라 3차원 주파수 분석, order tracking 등의 방법을 이용하여 분석된다. 반작용휠의 미소진동 분석 결과, 회전 속도와 비례하는 일차 성분 외에 고차 조화 성분, 구조 진동 성분, 회전 속도에 따라 고유진동수가 변하는 rocking 모드 성분 등을 관찰할 수 있었으며, 휠의 정적 및 동적 불균형은 각각 0.79gcm과 17.4gcm²으로 나타났다. 이러한 다양한 진동 성분들은 회전체의 특성, 구조물의 특성 및 베어링의 영향으로 기인한다.

• 전자공학회논문지A
• /
• 제32A권9호
• /
• pp.142-151
• /
• 1995

The trend of compact size, light weight, low power consumption in the portable telecommunication equipments demands large scale integration and low voltage operation of chips and the minimization of the number of the components in the telecommunication terminal. According to the trend, existing chip components are modulized and are integrated as a part into a bigger chip. This paper is about the development of the peripheral units of micro-controller for mobile telecommunication terminal. Peripherals consist of DMA controller, Interrupt controller, timer, watchdog timer, clock generator, and power management unit. They are designed to be integrated with EU(Execution Unit) and BIU(Bus Interface Unit) into a 16 bit micro-controller which will be used as a core of an ASIC for next generation digital mobile telecommunication terminal. At first, whole block of the micro-controller was described by VHDL behavioral model and simulated to verify its overall operation. Then, watchdog timer, clock generator and power management unit were directly synthesized by using VHDL synthesis tool. Rest of the pheriperal units were designed and simulated by using Compass Design Tool.

• 소성∙가공
• /
• 제21권6호
• /
• pp.348-353
• /
• 2012

Micro-drawn parts have received wider acceptance as products become smaller and more precise. The subject of this study was the deformation characteristics of ultra thin sheet metal in micro drawing of a rectangular shaped part. The influence of drawing speed and blank holding force on the product quality was investigated in micro-drawing of ultra thin sheet of beryllium copper (C1720) alloy. The specimen had a diameter of 4.8 mm and a thickness of $50{\mu}m$. Experiments were carried out in which, different blank holding force and drawing speed were considered. The product quality was evaluated by measuring the thickness and hardness along two specified directions, namely, the side and diagonal directions. The distribution of the thickness strain showed severe thinning especially around the punch radius in both directions. In the diagonal direction, thickening occurred in the flange area due to the axi-symmetric drawing mode. The increase of blank holding force and/or drawing speed was found to cause severe thinning around the punch radius. The blank holding force had a greater effect on thinning of the product than the drawing speed.