• Bulletin of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.731-736
• /
• 2014

An organic junction transistor with a vertical structure based on an active layer of poly(3-hexylthiophene) was fabricated by facile micro-contact printing combined with the Langmuir-Schaefer technique, without conventional e-beam or photo-lithography. Direct printing and subsequent annealing of Au-nanoparticles provided control over the thickness of the Au electrode and hence control of the electrical contact between the Au electrode and the active layer, ohmic or Schottky. The junction showed similar current-voltage characteristics to an NPN-type transistor. Current through the emitter was simply controllable by the base voltage and a high transconductance of ~0.2 mS was obtained. This novel fabrication method can be applied to amplifying or fast switching organic devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.841-845
• /
• 2013

We give a textured front on silicon wafer for high-efficiency solar cells by using micro contact printing method which uses PDMS (polydimethylsiloxane) silicon rubber as a stamp and SAM (self assembled monolayer)s as an ink. A random pyramidal texturing have been widely used for a front-surface texturing in low cost manufacturing line although the cell with random pyramids on front surface shows relatively low efficiency than the cell with inverted pyramids patterned by normal optical lithography. In the past two decades, the micro contact printing has been intensively studied in nano technology field for high resolution patterns on silicon wafer. However, this promising printing technique has surprisingly never applied so far to silicon based solar cell industry despite their simplicity of process and attractive aspects in terms of cost competitiveness. We employ a MHA (16-mercaptohexadecanoic acid) as an ink for Au deposited $SiO_2/Si$ substrate. The $SiO_2$ pattern which is same as the pattern printed by SAM ink on Au surface and later acts as a hard resist for anisotropic silicon etching was made by HF solution, and then inverted pyramidal pattern is formed after anisotropic wet etching. We compare three textured surface with different morphology (random texture, random pyramids and inverted pyramids) and then different geometry of inverted pyramid arrays in terms of reflectivity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.689-693
• /
• 2005

Inkjet printing is a non-contact and direct writing associated with a computer. In the industrial field, there have been many efforts to utilize the inkjet printing as a new way of manufacturing, especially for electronic devices. For the application of inkjet printing to electronic field, one of the key factors is exact realization of designed images into printed patterns. In this work, micro patterning for conducting line has been studied using the piezoelectric print head and silver nano ink. Dimensions of printed images have been predicted in terms of print resolution and diameter of a single dot. The predicted and the measured values showed consistent results. Using the results, the design capability for industrial inkjet printing could be achieved.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.717-718
• /
• 2008

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1118-1121
• /
• 2009

We have fabricated inverted staggered pentacene Thin Film Transistor (TFT) with 1-${\mu}m$ channel length by micro contact printing (${\mu}$-CP) method. Patterning of micro-scale source/drain electrodes without etching was successfully achieved using silver nano particle ink, Polydimethylsiloxane (PDMS) stamp and FC-150 flip chip aligner-bonder. Sheet resistance of the printed Ag nano particle films were effectively reduced by two step annealing at $180^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.7-14
• /
• 2010

This paper describes the effects of kinetic parameters such as attaching speed, attaching time, and dettaching speed on printing property of electrodes which were fabricated by micro-contact printing with Ag ink. In inking process the attaching speed was preferable to be less than 1 mm/s, attaching time as short as possible, and detaching speed larger than 1000 mm/s in order to obtain the transfer ratio of ink larger than 98%. Meanwhile in printing process the parameters were totally opposite to the results of inking process; attaching speed larger than 100 mm/s, attaching time larger than 30 sec, and detaching speed less than 1 mm/s for the best results. With the parameters we could obtain the micro-contact printed electrodes with the minimum line width of $30\;{\mu}m$, thickness of 300~500 nm, roughness less than 50 nm, and resistivity of about $15{\sim}16{\mu\Omega\cdot}cm$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.7-14
• /
• 2011

This paper is related to a roll-type micro-contact printing process. The proper parameters such as coating velocity, inking velocity, printing velocity and printing pressure as well as Ag contents of Ag ink were extracted to perform the fine patterning of Ag electrodes. Additionally we developed a process for PDMS with high uniform thickness. Finally, we obtained the Ag fine electrodes on $4.5cm\;{\times}\;4.5cm$ plastic substrate with the line width of 10 um, thickness less than 300 nm, surface roughness less than 40 nm, and the specific resistance of $2.08\;{\times}\;10^{-5}{\Omega}{\cdot}cm$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.571-575
• /
• 2016

Recently, there has been much focus on the controlled alignment and patterning process of nanowires for nanoelectronic devices. A simple and effective method for patterning of highly aligned nanowires using a microcontact printing technique is demonstrated. In this method, nanowires are first directionally aligned by contact printing, following which line and space micropatterns of nanowire arrays are accomplished by microcontact printing with a micro patterned NOA mold.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.354-359
• /
• 2006

Recently, the interest in lithography without photo exposure has been increased compare to the conventional photolithography in nano meter and micrometer size patterning area. We studied a self aligned dipping of Ag solution through micro contact printing (${\mu}-CP$) with octadecyltrichlorosilane (OTS) treated polydimethylsiloxane (PDMS) soft mold. The OTS monolayer on the patterned PDMS was formed by dipping it into OTS solution. We transferred the OTS monolayer from PDMS mold to the glass. The OTS monolayer changed the surface energy from hydrophilic surface to hydrophobic surface, And then we made self aligned Ag solution patterns just after dipping the substrate, using adhesion difference of Ag solution between OTS treated hydrophobic area and non-OTS treated hydrophilic area. We finally get the Ag patterns through only dip-coating after the ${\mu}-CP$ process. And we observed surface energies on the glass substrate through the contact angle measurements as time goes on.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2007.08a
• /
• pp.336-336
• /
• 2007