• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4B
• /
• pp.613-623
• /
• 2000

Digital TV tuner for 8-VSB modulation was developed with satisfying the requirements of ATSC. The double frequency conversion and the active tracking filter in the front-end were used to reduce interference of the adjacent channels and multi-channels, which suppress If beat and image band. However, it was impossible to get frequency mapping between tracking filter and first VCO(Voltage Controlled Oscillator) in the double conversion digital TV tuner differing from conventional NTSC tuner. This paper, therefore, suggests the available structure and a new method for automatic frequency selection by obtaining the mapping of frequency characteristic over tracking voltage and the combined hardware which compose of Micro-controller, EEPROM, D/A(Digital-to-Analog Converter), OP amp and switch driver to solve above problems.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.343-344
• /
• 2012

It has been known since the mid 1960s that Ag can be photodissolved in chalcogenide glasses to form materials with interesting technological properties. In the 40 years since, this effect has been used in diverse applications such as the fabrication of relief images in optical elements, micro photolithographic schemes, and for direct imaging by photoinduced Ag surface deposition. ReRAM, also known as conductive bridging RAM (CBRAM), is a resistive switching memory based on non-volatile formation and dissolution of a conductive filament in a solid electrolyte. Especially, Ag-doped chalcogenide glasses and thin films have become attractive materials for fundamental research of their structure, properties, and preparation. Ag-doped chalcogenide glasses have been used in the formation of solid electrolyte which is the active medium in ReRAM devices. In this paper, we investigated the nature of thin films formed by the photo-dissolution of Ag into Ge-Se glasses for use in ReRAM devices. These devices rely on ion transport in the film so produced to create electrically programmable resistance states. [1-3] We have demonstrated functionalities of Ag doped chalcogenide glasses based on their capabilities as solid electrolytes. Formation of such amorphous systems by the introduction of Ag+ ions photo-induced diffusion in thin chalcogenide films is considered. The influence of Ag+ ions is regarded in terms of diffusion kinetics and Ag saturation is related to the composition of the hosting material. Saturated Ag+ ions have been used in the formation of conductive filaments at the solid electrolyte which is the active medium in ReRAM devices. Following fabrication, the cell displays a metal-insulator-metal structure. We measured the I-V characteristics of a cell, similar results were obtained with different via sizes, due to the filamentary nature of resistance switching in ReRAM cell. As the voltage is swept from 0 V to a positive top electrode voltage, the device switches from a high resistive to a low resistive, or set. The low conducting, or reset, state can be restored by means of a negative voltage sweep where the switch-off of the device usually occurs.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.3
• /
• pp.294-299
• /
• 2010

ELT(Emergency Locator Transmitter) is used to send distress signal in the event of an aircraft crash. It is very useful but the ELT may transmit wrong signal caused by misjudging between crash and hard-landing. The reason of this problem is the low accuracy of the mechanical G-switch currently in use. To improve the ELT, we developed an ELT system using the MEMS(Micro Electro-Mechanical Sensor) accelerometer. The ELT system consists of acceleration data acquisition/analysis system, program of crash recognition, and GPS receiving system for the position information of an aircraft crash site. A free-drop table was developed for verification of the ELT system. The free-drop table was designed to replicate the acceleration and the pulse duration of the hard landing and the crash. By using the free-drop table, we showed that the ELT system performed well.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.1
• /
• pp.7-15
• /
• 2002

This paper is concerned with remote environment monitoring & control for the breeding house as scattering far and wide. The environment data is detected in the breeding house that is collected to one processor. It's adapted to the PSTN(public switch tele-phone network) and multi-processing for exchange the environment data and the control data in between the manager and a breeding house by micro-processor. We have designed the algorithm of the communication sequence through the experimental research. This system is composed of sensor interface, FSK communications, LED display, data latch and MCS-51 single-chip. The S/W is composed with data acquisition by multi-processing, data communication and interrupt. And this paper is Proposed the DB structure algorithm concern to a mount scale using web design. The subject is a performance of effective management for the breeding house.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.326-326
• /
• 2014

It has been known since the mid 1960s that Ag can be photodissolved in chalcogenide glasses to form materials with interesting technological properties. In the 40 years since, this effect has been used in diverse applications such as the fabrication of relief images in optical elements, micro photolithographic schemes, and for direct imaging by photoinduced Ag surface deposition. ReRAM, also known as conductive bridging RAM (CBRAM), is a resistive switching memory based on non-volatile formation and dissolution of a conductive filament in a solid electrolyte. Especially, Ag-doped chalcogenide glasses and thin films have become attractive materials for fundamental research of their structure, properties, and preparation. Ag-doped chalcogenide glasses have been used in the formation of solid electrolyte which is the active medium in ReRAM devices. In this paper, we investigated the nature of thin films formed by the photo-dissolution of Ag into Ge-Se glasses for use in ReRAM devices. These devices rely on ion transport in the film so produced to create electrically programmable resistance states [1-3]. We have demonstrated functionalities of Ag doped chalcogenide glasses based on their capabilities as solid electrolytes. Formation of such amorphous systems by the introduction of Ag+ ions photo-induced diffusion in thin chalcogenide films is considered. The influence of Ag+ ions is regarded in terms of diffusion kinetics and Ag saturation is related to the composition of the hosting material. Saturated Ag+ ions have been used in the formation of conductive filaments at the solid electrolyte which is the active medium in ReRAM devices. Following fabrication, the cell displays a metal-insulator-metal structure. We measured the I-V characteristics of a cell, similar results were obtained with different via sizes, due to the filamentary nature of resistance switching in ReRAM cell. As the voltage is swept from 0 V to a positive top electrode voltage, the device switches from a high resistive to a low resistive, or set. The low conducting, or reset, state can be restored by means of a negative voltage sweep where the switch-off of the device usually occurs.

• Journal of Biosystems Engineering
• /
• v.13 no.2
• /
• pp.38-45
• /
• 1988

This study was intended to develop the system automatically controlling travel direction of combine by means of sensing paddy rows. The control system was composed of three detecting levers having different length, micro-switch, microcomputer and electro-hydraulic control system. Sensor and control system developed was tested to estimate optimum design values and its actual performance as installed in combine. The computer simulation and performance test at simulated and actual field were conducted to test for possibility of practical use. The results of the study arc summarized. as follows: 1. The travel traces of combine hiving the conventional sensor with 2 levers and the new sensor detecting the slope of paddy rows were compared through computer simulation. Turning frequency of combine having new sensor was fewer than that of conventional sensor, but the rate of turning for the combine with new sensor was much greater than that of conventional sensor. 2. As sensor was established behind the tip of divider, the sensor itself well followed paddy rows but the tip of divider did not, resulting in divider being deviated from paddy rows. It was analyzed that the sensor should be attached closer to the tip of divider to have a better performance of the control system. 3. The greater the length of sensor lever for given location of sensor attachment and combine forward speed, the higher sensitivity of turning in control system. Moreover, increasing combine speed resulted in a worse performance of control system following paddy rows. Consequently, it was necessary that an optimum length of sensor attachment and for the range of combine operational speed. 4. Field test of combine installed with the sensor and electro-hydraulic system developed in this study showed that it may be operated smoothly and well behaved to paddy rows to 4th gear of combine speed which was 59cm/s. Consequently. it was concluded that the combine with the guidance control system developed in this study may be successfully used for paddy combining.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.11
• /
• pp.1584-1590
• /
• 2017

This paper presents a implementation method of reliable speed limitation controller considering motor parameter variation in high speed operation. In spinning process of drum washing machine, speed increase has to be limited when unallowable imbalance mass is detected. Otherwise, severe noise and vibration can happen because noise and vibration are proportional to imbalance mass. To detect imbalance mass, d-axis current magnitude is used. However, we have to compensate for back-emf and power supply variation by means of detecting them because d-axis current is affected by both of them. On the other hand, we have to carefully estimate back-emf because back-emf is affected by stator resistance variation and inverter voltage error. Stator resistance variation can happen by manufacturing process for mass production or temperature variation in running. And there are inverter voltage errors between command voltage from micro-computer to inverter and real voltage from inverter to motor because of rising and falling time delay and turn-on resistance of power semiconductor switch. To solve this problem, we propose 2-step align current injection method which is to inject step-wise current right before starting. By this method, we can simply obtain stator resistance by ratio of voltage without inverter voltage error and current, and we can measure inverter voltage error. So we can obtain more exact model current, and then by simple calculation with compensation gain, we can estimate more accurate motor back-emf. We show that this method works well. It is verified through experiments.

• Physical Therapy Korea
• /
• v.9 no.4
• /
• pp.1-11
• /
• 2002

본 연구의 목적은 이중과업 방법론(dual task methology)을 사용해서 젊은 사람과 노인을 대상으로 독립된 두 사건(two separate concurrent events)을 동시에 수행하는데 요구되는 주의력에 대한 분석과 노인에서의 특징적 차이를 찾는 것이다. 본 실험은 대상자가 힘판(force plate) 위에서 장애물(10cm) 보행시에 경피자극(cutaneous stimulation)에 대하여 마이크로 스위치(micro-switch)를 사용하여 반응하면서 시행되었다. 힘판과 시간(temporal events) 그리고 반응시간(reaction time)에 관한 자료들은 1000 Hz의 주파수로 수집되었다. 반응시간은 대상자들이 서 있는 상태(baseline) 장애물 보행시(dual task)에서 수집되었다. 반응시간은 아중과업 조건에서 대상자 모두에게서 긴 것으로 나타났으며 특히 노인에서 정상 성인보다 반응시간이 긴 것으로 나타났다. 이중과업 조건 하에서 노인 대상자가 정상 성인에 비해 발가락이 장애물에 닫지 않고 통과할 수 있는 공간, 즉 토우 클리어런스( toe-clearance)와 슬관전 굴곡(knee flexion) 각도가 훨씬 큰 것으로 나타났다. 이중과업 조건하에서 모든 대상자가 족관절 배측굴곡(ankle dorsiflexion) 각도를 감소시키는 것으로 나타났다. 노인들은 젊은 대상자들보다 훨씬 더 긴(124 ms) 유각시간을 보여 주었으며 정상 장애물 보행시 유각 시간은 이중과업보다 50 ms 긴 것으로 나타났다. 이러한 보행 특성의 차이는 노인대상자들이 젊은 대상자들보다 장애물 보행시에 이중과업의 영향을 더 받았기 때문인 것으로 판단된다. 이중 과업 시행시 이러한 토우 클리어런스의 감소와 장애물 통과시에 보행 속도의 증가는 아마도 낙상의 가능성을 증가시키는 요인이 될 수 있는 것으로 보여진다. 본 연구의 결과는 다중과업(multitasks)을 필요로 하는 보행 훈련 프로그램(gait training program)의 개발과 시행에 있어서 기초적인 자료를 제공할 수 있는 것으로 보여진다.

• Molecules and Cells
• /
• v.45 no.6
• /
• pp.403-412
• /
• 2022

Hypoxia leads to significant cellular stress that has diverse pathological consequences such as cardiovascular diseases and cancers. MicroRNAs (miRNAs) are one of regulators of the adaptive pathway in hypoxia. We identified a hypoxia-induced miRNA, miR-34c, that was significantly upregulated in hypoxic human umbilical cord vein endothelial cells (HUVECs) and in murine blood vessels on day 3 of hindlimb ischemia (HLI). miR-34c directly inhibited BCL2 expression, acting as a toggle switch between apoptosis and autophagy in vitro and in vivo. BCL2 repression by miR-34c activated autophagy, which was evaluated by the expression of LC3-II. Overexpression of miR-34c inhibited apoptosis in HUVEC as well as in a murine model of HLI, and increased cell viability in HUVEC. Importantly, the number of viable cells in the blood vessels following HLI was increased by miR-34c overexpression. Collectively, our findings show that miR-34c plays a protective role in hypoxia, suggesting a novel therapeutic target for hypoxic and ischemic diseases in the blood vessels.

• IMMUNE NETWORK
• /
• v.14 no.1
• /
• pp.21-29
• /
• 2014

Follicular helper T ($T_{FH}$) cells are recently highlighted as their crucial role for humoral immunity to infection as well as their abnormal control to induce autoimmune disease. During an infection, na$\ddot{i}$ve T cells are differentiating into $T_{FH}$ cells which mediate memory B cells and long-lived plasma cells in germinal center (GC). $T_{FH}$ cells are characterized by their expression of master regulator, Bcl-6, and chemokine receptor, CXCR5, which are essential for the migration of T cells into the B cell follicle. Within the follicle, crosstalk occurs between B cells and $T_{FH}$ cells, leading to class switch recombination and affinity maturation. Various signaling molecules, including cytokines, surface molecules, and transcription factors are involved in $T_{FH}$ cell differentiation. IL-6 and IL-21 cytokine-mediated STAT signaling pathways, including STAT1 and STAT3, are crucial for inducing Bcl-6 expression and $T_{FH}$ cell differentiation. $T_{FH}$ cells express important surface molecules such as ICOS, PD-1, IL-21, BTLA, SAP and CD40L for mediating the interaction between T and B cells. Recently, two types of microRNA (miRNA) were found to be involved in the regulation of $T_{FH}$ cells. The miR-17-92 cluster induces Bcl-6 and $T_{FH}$ cell differentiation, whereas miR-10a negatively regulates Bcl-6 expression in T cells. In addition, follicular regulatory T ($T_{FR}$) cells are studied as thymus-derived $CXCR5^+PD-1^+Foxp3^+\;T_{reg}$ cells that play a significant role in limiting the GC response. Regulation of $T_{FH}$ cell differentiation and the GC reaction via miRNA and $T_{FR}$ cells could be important regulatory mechanisms for maintaining immune tolerance and preventing autoimmune diseases such as systemic lupus erythematosus (SLE) and rheumatoid arthritis (RA). Here, we review recent studies on the various factors that affect $T_{FH}$ cell differentiation, and the role of $T_{FH}$ cells in autoimmune diseases.