• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.88-95
• /
• 2004

Micro stepping method is adopted in order to eliminate effectively the resonant phenomena and to increase the positional resolution. Exist micro-step method by using Sinusoidal waveform, drive circuit is complex by using micro controller and ROM, it have fault on cost Increase. This paper proposed trapezoidal current wave form for simple control circuit and micro stepping method by using a low cost controller. This paper proposed method verify by using CPLD(EPM9320RC208-15) of low cost. This paper make experiment that comparison of exist method and proposed method. This paper obstruct a escape of motor by using high speed detect.

• Journal of the Korea Safety Management & Science
• /
• v.17 no.3
• /
• pp.363-370
• /
• 2015

In this paper, the control technique of the stepping motor using back electromotive force(B-EMF) without encoder is investigated. The stepping motor generally uses the rotary encoder to detect the rotor position. Since this method increases the cost and the motor configuration size, the new closed-loop control method applied for the B-EMF was implemented by using current detect circuit, AD-converter, and micro controller unit(MCU). The control loop of stepping motor became very simplified. The current change of stepping motor measured by the amplifier was measured and analyzed, when the missing step is occurred. Based on the data from current feedback, position errors were compensated and confirmed by using AD-converter.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.43-51
• /
• 2010

Speed, accuracy and smoothness are the important properties of pan-tilt camera. In the case of a high ratio zoom lens system, low vibration characteristic is a crucial point in driving pan-tilt mechanism. In this paper, a novel micro-stepping controller with a function of reducing vibration was designed using field programmable gate arrays (FPGA) technology for high zoom ratio pan-tilt camera. The proposed variable reference current (VRC) control scheme reduces vibration decently and optimizing coil current in order to prevent the step motor from occurring missing steps. By employing VRC control scheme, the vibration in low speed could be significantly minimized. The proposed controller can also make very high speed of 378kpps micro-step driving, and increase maximum acceleration in motion profiles.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.228-231
• /
• 1987

Microprocessor-based software DDA interpolator is developed and applied to two axis contouring control of X-Y table. Developed assembly program is composed of feedrate, linear and circular DDA interpolation routines. Reference-pulse type of open-loop stepping motor control system in which the micro-computer produces a sequence of reference pulses for each axis of motion is adopted. To test performance of the developed program, X-Y table drive system based on stepping motor and shaft encoder is designed. Contouring error of the system in linear and circular path is within .+-.0.2 mm.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.11
• /
• pp.1042-1048
• /
• 2012

A 2-axis gimbal system is one of main disturbance sources affecting image jitter response of a satellite. The gimbal system comprises azimuth stage and elevation stage, and these pointing mechanism can be rotated by stepping motors about its azimuth and elevation axes simultaneously. Because of the complex and coupled dynamic motion of the gimbal system, its moment of inertia and structural modes can be changed according to the system configuration, and thus the gimbal system generates complicated and non-linear disturbance characteristics. In order to improve the jitter response of a spacecraft, it is an indispensable process to reduce the micro-vibration disturbance level of the antenna system. In the present research, a 2-axis gimbal system was manufactured and then its micro-vibration test was performed in terms of two types of stepping motors(2-phase and 5-phase). The test results show that the disturbance level of the gimbal system can be reduced by replacing the 2-phase stepping motor with the 5-phase one, and the average disturbance attenuation ratio is 56 % in peak level and 48 % in standard deviation level. The experimental results confirm that it is an efficient jitter reduction method to adopt a high-phase stepping motor.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.451-454
• /
• 2002

In this paper, studied on the one-chip design of low cost for the micro-stepping drive having 5-phase Pentagon Type winding. Micro-stepping method in order to eliminate effectively the resonant phenomena and to Increase the positional resolution. This paper proposed trapezoidal current wave- form for current control and provided design- method by using only one-chip of low cost. Therefore the drive will be simple and small size. Also the drive will have a lot of advantage at commercial business. Finally the above study has been implemented on the VHDL. Simulation has been performed to verify the PWM for micro-stepping drive.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.6-8
• /
• 2004

Recently, the PM type stepping motor preferred solution for many small electronics position determination devices since it is small in size. Thus, there are glowing demands for permanent magnet(PM) type stepping motor that greater mechanical output, smaller size. This paper deals with a study of the miniaturization of the PM type stepping motor with claw-poles. We introduced the small-sized PM type stopping motor that has new structure and analyzed the magnetic characteristic of it versus general type model using 3-D finite element analysis(FEA).

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.96-98
• /
• 2005

This paper presents a new two-phase linear hybrid stepping motors (LHSM), which has two windings per phase and one of them shares the other phase winding. The proposed motor shows a unique ability to deliver low cogging force without any particular complex control scheme and additional power electronics hardware in micro stepping control. An analytical and experimental comparison between conventional and proposed LHSM is evaluated to confirm the effectiveness of the proposed design.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.45-47
• /
• 2005

A digital controller of stepping motors is designed for removing mid-range resonance. Rotor oscillation is detected from motor currents and the microprocessor generates frequency modulation taking into account rotor oscillation. ATmega16 is employed and the controller drives stepping motors up to 3000[rpm] at micro stepping.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2166-2168
• /
• 1998

A PWM inverter using power FET is developed to switch the excitation current of 5 phase hybrid stepping motor for the use of driving X, Y table. A micro processor based controller is also developed to control the excitation current switching of X, Y axis stepping motor as well as synchronizing operation of Z-axis servo motor. The developed driving control system is applied to the industrial embroidery sewing machine.