• 대한기계학회논문집
• /
• 제9권5호
• /
• pp.564-571
• /
• 1985

본 논문에서는 미시조직인자를 변화시킨 마르텐사이트-페라이트 복합조직강을 준비하여 균열선단 및 안정영역의 파괴양상과 파괴저항과의 관계를 검토하였다.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.203-210
• /
• 2011

Bake hardening steels have to resist strain aging to prevent the yield strength increment and stretcher strain during press process and to enhance the bake hardenability during baking process after painting. The bake hardening steels need to control the solute carbon and the solute nitrogen to improve the bake hardenability. Ti and/or Nb alloying for nitride and carbide precipitation and low carbon content below 0.003% are used to solve strain aging and formability problem for automotive materials. However, in the present study, the effect of micro-precipitation of copper sulfide on the bake hardenability and fatigue properties of extremely low carbon steel has been investigated. The bake hardenability of Cu-alloyed bake hardening (Cu-BH) steel was slightly higher (5 MPa) than that of Nb-alloyed bake hardening (Nb-BH) steel, but the fatigue limit of Cu-BH steel was far higher (45 MPa) than that of Nb-BH steel. All samples showed the ductile fracture behavior and some samples revealed distinct fatigue stages, such as crack initiation, stable crack growth and unstable crack growth.

• 비파괴검사학회지
• /
• 제21권1호
• /
• pp.32-38
• /
• 2001

재료의 손상을 평가하기 위하여 초음파법에 대한 많은 연구가 진행되었고 널리 사용되고 있으나 대부분 균열의 성장 또는 두께의 감소와 같은 문제에 집중되고 있다. 본 연구에서는 2.25Cr-1Mo 강을 이용하여 반복하중에 의해 재료내부에 발생하는 미시균열을 조기에 감지하고, 피로에 의한 파괴를 미연에 방지할 수 있도록 초음파 표면파의 감쇠와 속도변화를 이용하여 균열길이 측정의 정량적인 평가방법을 제시하였다. 중심주파수 5MHz의 탐촉자를 이용하여 파단수명비 약 60%, 균열길이 약 2mm 정도에서 표면파의 속도 및 감쇠 변화를 탐지할 수 있었다. 고주파 탐촉자를 이용함으로써 미시균열의 발생을 조기에 탐지할 수 있으며, 파단수명을 예측하는 기초자료로 활용할 수 있다.

• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.298-304
• /
• 2001

Turbine blade is subject to force of three types ; the torsional force by torsional mount, the centrifugal force by the rotation of rotor and the cyclic bending force by steam pressure. The cyclic bending force was a main factor on fatigue strength. SEM fractography in root of turbine blade showed micro-clack width was not dependent on stress intensity factor range. Especially, fatigue did not exist on SEM photograph in root of turbine blade. To clear out the fracture mechanism of turbine blade, nanofractography was needed on 3-dimensional crack initiation and crack growth with high magnification. Fatigue striation partially existed on AFM photograph in root of turbine blade. Therefore, to find a fracture mechanism of the torsion-mounted blade in nuclear power plant, the relation between stress intensity factor range and surface roughness measured by AFM was estimated, and then the load amplitude ΔP applied to turbine blade was predicted exactly by root mean square roughness.

• 한국해양공학회지
• /
• 제15권1호
• /
• pp.52-56
• /
• 2001

This study were looks at the effect of the initial cut length or stress concentration level, on the wave forms produced by crack propagation. The signals were collected, then classified visually for each type of sample. They were put into three classes according to their shapes in the time and frequency domain. Each class should domain signals which could be correlated to a certain micro-failure mechanism that occurs during the fatigue process. Classes of these signals compared, with each sample. To see if there were any classes common to the three samples. The fatigue test attempted to determine if the initial cut length has any influence on the type of signals.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.535-538
• /
• 2005

The problem of the crack which occures from the reinforced concrete structure. could be caused by the complexed factors. When the crack happen, it caused fatal blemish to manage and maintain the structure such as structural problem, licking, spalling, viewing Even though they study and work hard to solve this kind of problem in the world, there are no countermeasure for perfect prevention of crack. After the crack checked out, a method of repair-reinforcement has been sutdied and operated actively. In this experiment, studied durability of repair material. Experiment wave and durability of epoxy and urethane's were shown good result, and micro cement's durability displayed result that is not good. Result of a repeat tired experiment displayed result that micro cement is bad.

• 열처리공학회지
• /
• 제27권4호
• /
• pp.191-201
• /
• 2014

The gear was made of SNC815 case-carburized, quench hardened and tempered steel. The gears were failed far earlier than the expected service life used in the industrial site. Causes of the failed gear were analyzed by microstructure observation. By the SEM and micro structure examinations, the damaged surfaces had been weared and failed by fatigue. Through microscope observation on the damaged surface, it was found that the cause of failure was determined by external overloading and the initial stage of the damage was closely related to complex contact fatigue failure. The overload and contact fatigue contributed to the early failure cause.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1493-1502
• /
• 1992

본 연구에서는 크랙선단의 소성변형에 의해 발생하는 소성유기 크랙개구거동 을 검토하기 위하여, 크랙선단 최인접 영역에서 COD를 측정할 수 있는 직접 측정법을 개발 사용하고 (1) 직접측정법의 적용범위와 크랙선단의 개구거동 (2) 측정위치에 따 른 개구하중의 변화 (3) 개구비에 영향을 주는 하중변수등에 대하여 고찰하였다.

• 열처리공학회지
• /
• 제21권1호
• /
• pp.10-19
• /
• 2008

To investigate the effect of ultrasonic nano-crystalline surface modification (UNSM) treatment on rolling contact fatigue and residual stress properties of bearing steels, this paper carried out a rolling contact fatigue test, measured residual stress and retained austenite, performed a wear test, observed microstructure, measured micro hardness, and analyzed surface topology. After the UNSM treatment, it was found that the surface became minute by over $100{\mu}m$. The micro surface hardness was changed from Hv730~740 of base material to Hv850~880 with about 20% improvement, and hardening depth was about 1.3 mm. The compressive residual stress was measured as high as -700~-900 MPa, and the quantity of retained austenite was reduced to 27% from 34%. The polymet RCF-6 ball type rolling contact fatigue test showed over 4 times longer fatigue lifetime after the UNSM treatment under 551 kgf load and 8,000 rpm. In addition, this paper observed the samples, which went through the rolling contact fatigue test, with OM and SEM, and it was found that the samples had a spalling phenomenon (the race way is decentralized) after the UNSM treatment. However, before the treatment, the samples had excessive spalling and complete exploration. Comparison of the test samples before and after the UNSM treatment showed a big difference in the fatigue lifetime, which seems to result from the complicated effects of micro particles, compressive residual stress, retained austenite, and surface topology.

• 대한기계학회논문집
• /
• 제9권1호
• /
• pp.1-9
• /
• 1985

본 연구에서는 이러한 점에도 역점을 두어서 초기 피로균열의 발생.거동을 관 찰하기 쉬운 연강을 선택하여 편진인장반복하중을 작용시켜, 연강 평골재의 표면상에 발생.성장하는 미소표면균열의 거동을 전자현미경과 광학현미경을 병용하여 표면과 파 단면을 입체적으로 조사하여, 피로균열의 초기발생상태를 조사하고, 그 성장율을 조사 하여 파괴역학적으로 해석하여 그 특성을 조사한다.