• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.6
• /
• pp.457-465
• /
• 2018

Since IMO has discussed the effectuation of the EEDI, EEOI and SEEMP, each country, shipping company, shipbuilding company and research institute have been requested to prepare the design, construction and operation of the efficient ship. From the shipbuilding company's point of view, it was necessary to develop a method based on the maneuvering equations of motion in a bid to estimate the EEOI considering the design, model test results and the calculation results of the ship. In this paper, the estimation method of RPM, power and fuel consumption proposed in the previous research was developed to construct a framework that helps in the estimation of the EEOI. It was possible to estimate the EEOI from the estimated ship speed (distance), LNG cargo mass, fuel consumptions and emission factors according to the type of fuel. The rapid increase of the evaluated EEOI was observed when the LNGC with ME-GI engine executing the course changed with a large difference. This prompted the comparison of the type of fuel on the estimated EEOI by considering HFO, LNG fuel and MGO properties.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.5
• /
• pp.358-366
• /
• 2023

Due to the International Maritime Organization's (IMO) environmental regulations on NOx and SOx, LNG-fueled eco-friendly ships are gaining attention worldwide, and various eco-friendly ships are being proposed and demanded for conversion to eco-friendly ships in Korea, as the eco-friendly ship law has recently been enforced. In this study, the initial basic design was performed to convert an existing Marine Gas Oil (MGO) fueled ship into an LNG-DF propulsion ship, targeting medium-sized ship, to select the fuel tank capacity and main dimensions and appropriate fuel ratio between the two fuels. In particular, Sustainable basic design method considering environmental impact were proposed by performing a Life Cycle Assessment (LCA) throughout the design process, and various design options were compared and analyzed to meet different design conditions by applying them.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.184-189
• /
• 1999

1000 $\AA$ thick Fe films were epitaxially grown on MgO(001) by an rf sputtering and effects of substrate temperature on the structural and magnetic properties were investigated. X-ray diffraction intensity increased with increasing substrate temperature and inter-planar spacing $d_{(002)}$ decrease with increasing the temperature up to 25$0^{\circ}C$. The increased intensity and decreased inter-planar spacing were thought to be attributed to the enhancement of lattice match between Fe films and MgO, thus yielding good epitaxial growth. By using torque magnetometer, VSM and pole figure, very nice epitaxial growth of sputtered Fe films on MgO could be confirmed and $K_1$ value of Fe films grown at 25$0^{\circ}C$ was $4.6{\times}10^5\;erg/cc$, which was very similar to that of bulk single Fe crystal.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.12-17
• /
• 2007

The effects of the evaporation rate of MgO films using an electron beam on the MgO properties and the discharge characteristics of a plasma display panel(PDP) were investigated and analyzed. Mgo films were deposited with the various MgO evaporation rates. The MgO properties such as the crystal orientation, the surface roughness, and the film structure, were inspected using XRD(X-ray diffractometry), AFM(atomic force microscopy). From the experiments and Paschen law, the maximum value of the secondary, electron emission coefficient $(\gamma)$ was obtained at the evaporation rate of $5\AA/sec$. The minimum firing voltage and the maximum luminous efficiency were obtained at an evaporation rate of $5\AA/sec$. In the MgO film deposited at $5\AA/sec$, the (200) orientation and $F^+$ center were most intensive. The XRD results and cathode-luminescence(CL) spectra show the $\gamma$ values are correlated with $F/F^+$ centers of the molecular structure of MgO films.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.55-55
• /
• 2003

Ferroelectric 물질은 고유전성, 자발분극과 전기장에 따른 유전상수의 변화 등의 특성을 가지고 있으므로 많은 연구가 진행중이다. 이러한 ferroelectric 물질의 유전 특성에 미치는 요소로는 물질의 조성비, 박막의 스트레스, 결정성 등이 있다. 특히 스트레스에 대한 연구가 활발히 진행중이다. 본 연구에서 산화물 인공격자를 이용하여 단일박막에서 얻을 수 없는 격자변형도를 얻어 격자 변형이 박막의 유전특성에 미치는 영향을 연구하였다. BaTiO$_3$ (BTO)/SrTiO$_3$ (STO) 산화물 인공격자를 Pulsed laser deposition (PLD)법으로 (La,Sr)CoO$_3$ 전극이 코팅된 MGO (100) 단결정 기판위에 증착시켰다. 적층 주기에 변화를 주어 BTO와 STO 각각 1.01~1.095와 0.925 ~ 1.003의 단일 막에서는 얻을 수 없는 격자 변형도를 얻었다. 이 실험적 데이터를 기초로 하여 density functional theory (DFT)라고 불리는 범함수밀도론를 기초한 제일원리적 계산 방법을 통하여 격자 변형된 SrTiO$_3$의 구조적, 전기적 특성을 계산하였다. SrTiO$_3$와 BaTiO$_3$ 격자의 안정성을 분석하기 위하여 Vienna Ab-intio Simulation Package (VASP) code가 사용되었다. SrTiO$_3$와 BaTiO$_3$ 산화물 격자의 안정성 분석 후, frozen-phonon 계산 방법을 사용하여 zone-centered optical phonon mode가 계산되었으며, mode effective charge는 Berry-phase polarization 으로부터 얻어졌다. SrTiO$_3$ 격자가 격자변형이 일어나지 않은 상태로부터 c/a= 0.985로 격자 변형 이 일어남에 따라 optical phonon mode는 점차 hardening되었다. BaTiO$_3$ 격자의 경우 SrTiO$_3$ 격자와는 달리 격자 변형이 1.01~1.023으로 진행됨에 따라 optical phonon mode의 증가를 가져왔으나 Born effective charge의 증가하였으며, 더 이상 격자 변형이 진행됨에 따라 optical phonon mode의 감소를 가져왔으나 Born effective charge의 증가 유전상수는 증가했다. 격자 변형이 SrTiO$_3$ 와 BaTiO$_3$ 산화물 격자의 optical phonon mode와 Born effective charge에 크게 영향을 미쳤다.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.5
• /
• pp.651-658
• /
• 2018

Particulate matter (PM) emitted from fossil fuel-combustion facilities can be classified as either filterable or condensable PM. The U.S. Environmental Protection Agency (EPA) defined condensable PM as material that is in the phase of vapor at the stack temperature of the sampling location which condenses, reacts upon cooling and dilution in the ambient air to form solid or liquid in a few second after the discharge from the stack. Condensable PM passed through the filter media and it is typically ignored. But condensable PM was defined as a component of primary PM. This study investigates the change of condensable PM according to the variation in the sulfur dioxide of combustion gas. Domestic oil boilers were used as the source of emission ($SO_2$) and the level of $SO_2$ concentration (0, 50, 80, and 120 ppm) was adjusted by diluting general light oil and marine gas oil (MGO) that contains sulfur less than 0.5%. Condensable PM was measured as 2.72, 6.10, 8.38, and $13.34mg/m^3$ when $SO_2$ concentration in combustion gas were 0, 50, 80, and 120 ppm respectively. The condensable PM tended to increase as the concentration of $SO_2$ increased. Some of the gaseous air pollutants emitted from the stack should be considered precursors of condensable PM. The gas phase pollutants which converted into condensable PM should reduced for condensable PM control.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.3
• /
• pp.119-126
• /
• 1997

Recently, duc to highly increased consumption of' ngg~.egatc>s f o ~ . construction. studies have focused on the effective utilization of rock wastes abandoned so far. This study was designed, firstly, to determine t,hc petrological, g'ochemical and mechanical cha~,acte~istics of' crushed limestone aggregates in thc Samhwa district for suitable construction aggregates and, secondly, to offer basic data for cff'ective utilization of low grade limestones. Results of' the petrographic st,udy indicates that the crushed limestone aggregates in the Samhwa district can bo separate4 into two groups, namely f'inc-grained and cowlxcgrained limestones. Dominantly distributed fine-grained limestone containing some dolomite has higher Mgo and $SiO_2$ contents compared to the coarse-graincd limestonr. It, can be classified as medium strength rock by the physical and mcxhanical pi.opertics. I3ased on the size of' mineral grains and chemical compositions, it is suggested that the crushed limestone aggregates in t,his study area would bctkr be u s ~ i for asphalt concr.ctt., road pavement, or railroad ballast materials than for cement concrete.

• Journal of the Korean Vacuum Society
• /
• v.11 no.3
• /
• pp.135-140
• /
• 2002

In this paper, We deposited the BST thin-film on p-type (100)Si, (100)MgO and MgO/Si substrates respectively using RF magnetron sputtering method. After the BST thin-fil m was deposited, we performed RTA(rapid thermal anneal) at $600^{\circ}C$, oxygen atmosphere and 1 min. In the XRD measurement, we observed the (110) $Ba_{0.5}Sr_{0.5}TiO_3$ main peak in all samples and the peak intensity increased after post annealing. Then we manufactured a capacitor using Al Electrode and measured I-V, C-V. In C-V measurement result values for each substrate, dielectric constant was calculated 120 (bare Si), 305(MgO/Si), 310(MgO) respectively. A leakage current density was present less than 1 $\mu\textrm{A/cm}^2$ at applied fields below 0.3 MV/cm. In conclusion we confirmed that MgO/Si substrates give good results for BST thin-film deposition.

• YAKHAK HOEJI
• /
• v.40 no.1
• /
• pp.25-35
• /
• 1996

Magaldrate. an antiacid was synthesized by reacting magnesium oxide, aluminum sulfate, and dried aluminum hydroxide gel. The optimum synthesis conditions based on the yield of t he product were established by applying Box-Wilson experimental design. It was found that the optimum synthesis conditions of Magaldrate were as follows: Reaction temperature; 61~$85{\circ}C$, concentration of two reactants. Mgo and $Al(OH)_3$: 16~19.8%, molar concentration ratio of two reactants, [MgO]/[$Al(OH)_3$]; 4.2~5.0, temperature of washing water; 36~$41^{\circ}C$ and drying temperature of the product: 76~$80^{\circ}C$. Magaldrate was synthesized under the optimum synthesis conditions and identified by analyzing the chemical composition, and by differential scanning calorimetry and X-ray diffraction method. The Magaldrate sample synthesis under these conditions was used to prepare 15.6% Magaldrate original suspension which was utilized to make 13% Magaldrate suspension dispered in various concentrations of eight types of suspending agents. The acid-neutralizing capacity of 13% Magaldrate suspension dispersed in 0.25% suspending agents was examined by Rosset-Rice method. The maximum pH was reached within 1 minute in all suspension tested, and duration maintained between pH 3~5 was decreased in the order of Na alginate Na silicate(meta) Veegum HV pectin agar>Na>CMC>xanthan gum>bentonite. It was found that the hysteresis loop area was increased with temperature in the case of Riopan Plus and the addition of agar, whereas the area was decreased with temperature in the case of the addition of Na alginate and xanthan gum. 13% Magaldrate suspension tends to sediment by the addition of bentonite.

• Journal of the Speleological Society of Korea
• /
• v.14 no.15
• /
• pp.42-90
• /
• 1987

Lee, Moon Won reported by 63 kinds lescribing the petrography and bulk chemical Composition in Petrology of Cheju volcanic island. The total Chemical Composition data was analyzed by the program of FORTRAN77. First, the Conversition equations and the scatter diagram were examined to the analysis, by the least square method. Next, a statistical data requested a mean Value, maximum value, minimum value, the range, the standard deviation, the variance, the Standord Error and the Coefficient of variation. In the standard deviation, a small Composition is MnO and P$_2$O$\sub$5/, a large Composition is SiO$_2$, Mgo and FeO. The Standard error and the variance were the tandency looked like the Standard deviation well. However, the Coefficient Variation differs from the Standard deviation. Where, a large Coefficient of variation are H$_2$O$\^$-/ and H$_2$O$\^$+/, a small Coefficient of variation are Al$_2$O$_3$ and SiO$_2$. The Correlation of Coefficient Can be Calculated numerically from the relation between SiO$_2$, Al$_2$O$_3$ and TiO$_2$ to other Compositions.