• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.62-62
• /
• 2013

Magnesium alloys exhibit many attractive properties such as low density, high strength/weight ratio, high thermal conductivity, very good electromagnetic features and good recyclability. However, most commercial magnesium alloys require protective coatings because of their poor corrosion resistance. Attempts have been made to improve the corrosion resistance of the Mg alloys by surface treatments, such as chemical conversion coatings, anodizing, plating and metal coatings. Among them, chemical conversion coatings are regarded as one of the most effective and cheapest ways to prevent corrosion of Mg alloys. In this study, the effects of various $Zn^{2+}$ concentrations and pH levels on the formation of zinc phosphate conversion coatings (ZPCCs) on AZ31 magnesium alloy were investigated, and corrosion resistances of the coated samples were evaluated by immersion test and potentiodynamic polarization experiment. The corrosion resistance of the coated AZ31 samples was found to increase with increasing $Zn^{2+}$ concentration and the lowest corrosion rate was obtained for the samples coated at pH of 3.07, independent of $Zn^{2+}$ concentration. The best coatings on AZ31 were obtained at [$Zn^{2+}$] = 0.068 M and pH 3.07. At the conditions of [$Zn^{2+}$] = 0.068 M and pH 3.07, the formation and growth processes of ZPCCs on AZ31 Mg alloy are divided into four stages: formation of a dense layer, precipitation of fine crystals on the dense layer, growths of the inner and outer layers, and reorganization of outer crystalline layer.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.672-677
• /
• 1998

The following work examines the growth rate and microstructure of the $AI_2O_3$-composite formation by melt oxdation of pentad AI-alloys. The I weight % of each metal elements Cu and Ni were added to AI-IMg-3Si-3Zn and AI-IMg- 3Si-5Zn alloys. The diffenent pentad AI-alloys were oxidized 20 hours long at 1373K and 1473K. The oxidation rates were determined by observing the weight gain. The macro- and microstructure of formed oxide layer were examined by optical microscopy. The AI-IMg-3Si-5Zn-lCu alloy revealed the best oxidation behavior, but formedoxide layer was inhomogeneous.The oxidation rate were accelerated, and the uniform growth of the oxide layer with fine microstructure were obtained by putting a thin layer of $SiO_2$ on the surface of the alloy.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.1 s.34
• /
• pp.73-76
• /
• 2005

To widen the band gap of ZnO, we have investigated $Zn_{1-x}Mg_xO(ZMO)$ thin films prepared by pulsed laser deposition on c-plane sapphire substrates at $500^{\circ}C$. From X-ray diffraction patterns, ZMO films show only the (0002) and (0004) diffraction peaks. It means that the flints have the wurtzite structure. Segregation of ZnO and MgO phases is found in the films with x=0.59. All the samples are highly transparent in the visible region and have a sharp absorption edge in the UV region. The shift of absorption edge to higher energy is observed in the films with higher Mg composition. The excitonic nature of the films is clearly appeared in the spectra for all alloy compositions. The optical band-gap ($E_g$) of ZMO films is obtained from the ${\alpha}^2$ vs Photon energy plot assuming ${\alpha}^2\;\propto$ (hv - $E_g$), where u is the absorption coefficient and hv is the photon energy. The value of $E_g$ increases up to 3.72 eV for the films with x=0.35. It is important to adjust Mg composition control for controlling the band-gap of ZMO films.

• Journal of Powder Materials
• /
• v.15 no.2
• /
• pp.95-100
• /
• 2008

The investigation is to modify the mechanical and chemical properties of Mg alloys using a combination of rapid solidification and surface treatment. As the first approach, $Mg_{95}Zn_{4.3}Y_{0.7}$ was gas atomized and pressure sintered by spark plasma sintering process (SPS), showing much finer microstructure and higher strength than the alloys as cast. Further modification was performed by treating the surface of PM Mg specimen using Plasma electrolytic oxidation (PEO) process. During the PEO processing, MgO layer was initiated to form on the surface of Mg powder compacts, and the thickness and the density of MgO layer were varied with the reaction time. The thickening rate became low with the reaction time due to the limited diffusion rate of Mg ions. The surface morphology, corrosion behavior and wear resistance were also discussed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.94-95
• /
• 2014

The purpose of this study is to evaluate the corrosion protective property of Al-Mg high-freqeuncy arc metal spray method in comparison to Zn-Sn and Zn-Al alloys by electrochemical method and CASS test. As a result, it appeared that Al-Mg alloy had very higher corrosion protective property through the electrochemical characteristic and the CASS test comparing with the other alloys.

• Journal of Korea Foundry Society
• /
• v.17 no.5
• /
• pp.419-425
• /
• 1997

용탕단조방법에 의해 제조된 Mg-6Al-xZn(x=0, 1, 2)합금의 기계적 성질에 미치는 시효열처리의 영향을 조사한결과 아래와 같은 결론을 얻었다. (1) 주조조직을 관찰한 결과 미세한 수지상조직을 나타냈으며 초정${\alpha}$, 과포화 ${\alpha}$, ${\beta}$상 등 세가지 상으로 구성되어 있었다. (2) Mg-6Al-xZn합금은 시효경화성을 나타내었으며 Zn의 첨가량이 증가할수록 전시효구간에서 경도값이 높게 나타났다. (3) 시효조직을 관찰한 결과 $200^{\circ}C$의 시효시에는 불연속 석출물이 대부분 차지했으나 $240^{\circ}C$의 시효온도에서는 수지상 경계에서 시작되는 미세분산된 연속석출물이 대부분 이었다. (4) $240^{\circ}C$에서 시효열처리 한 시편은 연속석출물이 석출됨으로서 $200^{\circ}C$에서의 시효열처리된 시편에 비하여 과시효되는 경향이 작았다. (5) T6열처리 후 인장시험 결과 Zn 첨가량에 따라 강도가 증가하였는데 Mg-6Al-2Zn합금의 경우 인장강도는 248.4 MPa을 나타내었으며 Zn양에 따른 연신율의 감소는 나타나지 않았다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.170.1-170.1
• /
• 2016

일반적으로 Al-Mg-Zn 합금의 ${\beta}$상($Al_aMg_b$) 조직은 내식성의 큰 영향을 미치는 것으로 알려져 있으며 ${\beta}$상 조직이 입계에 연속적으로 형성될 경우 내식성이 감소하는 주요 원인이 되고 있다. 따라서 본 연구에서는 Al-Mg-Zn 합금을 균질화하여 ${\beta}$상 조직을 변화시켰고, 그 변화에 따른 내식성의 거동을 확인하였다. 균질화 조건은 ${\beta}$상 조직의 고용 가능한 온도인 $400^{\circ}C$이상의 온도에서 진행 하였으며 균질화 조건에 따른 미세조직, 조성 분석, ${\beta}$상 조직의 고용정도를 확인하기위해 광학현미경(optical microscpe), 전자현미경(scanning electron microscope), X선 회절 분석법(X-ray Diffraction)을 사용하였다. 또한, 미세조직에 의한 내식성은 $25^{\circ}C$, 3.5wt% NaCl용액에서 분극 시험으로 평가하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.1
• /
• pp.33-41
• /
• 2003

The optical properties of $ZnS_ySe_{1-\chi-y}:Te_{\chi}(\chi<0.08,y~0.11)$ alloys grown by molecular beam epitaxy (MBE) have been investigated by photoluminescence (PL) and PL-excitation (PLE) spectroscopy. Good optical properties and high crystal quality were established with lattice match condition to GaAs substrate. At room temperature, emission in the visible spectrum region from blue to green was obtained by varying the Te content of the ZnSSe:Te alloy. The efficient blue and green emission were assigned to $Te_1 and Te_n(n\geq2)$cluster bound excitons, respectively. Bright green (535 nm) and blue (462 nm) light emitting diodes (LEDs) have been developed using ZnSSe:Te system as an active layer. The turn-on voltage of 2.1 V in current-voltage characteristics is very small compared to that of commercial InGaN-based LEDs (>3.4 V), indicating the formation of a good ohmic contact due to the optimized p-ZnSe/p-ZnTe multi-quantum well (MQW) superlattice electrode layers.

• Transactions of Materials Processing
• /
• v.19 no.7
• /
• pp.429-434
• /
• 2010

The material used is a commercial magnesium based alloy AZ31(Mg-3Al-1Zn) sheet with a thickness of 0.8 mm. Friction tests at various temperatures(R.T. to $200^{\circ}C$) and at various holding forces in the 4 type molds were carried out to investigate the coefficient of friction. A warm drawing process with a local heating and cooling technique was developed in the Mg alloy sheet forming to improve formability because it is very difficult for Mg alloy to deform at room temperature by the conventional method. So, the coefficient of friction at various mold surface treatment conditions in this study was needed to develop the Mg alloy sheet forming technology.

• Applied Microscopy
• /
• v.32 no.1
• /
• pp.31-37
• /
• 2002

As-cast microstructure of Mg-rich $Mg_{68}Zn_{28}Y_4$ has been investigated by a detailed transmission electron microscopy. The as-cast $Mg_{68}Zn_{28}Y_4$ alloy consisted of three different types of phases: $10{\sim}20{\mu}m$ size primary solidification phase, dendritic phase grown from the primary phase and a eutectic structure formed at the later stage of solidification. The primary solidification phase has an icosahedral structure with a large degree of phason strain. 1/1 rhombohedral approximant phase with lattice parameters: $a=27.2{\AA}\;and\;{\alpha}=63.43^{\circ}$ is first observed in Mg-Zn-Y system. The rhombohedral structure can be obtained by introducing phason strain in the six dimensional face centered hyper-cubic lattice. The decagonal phase nucleates with orientation relationship with the icosahedral phase, and $Mg_4Zn_7$ nucleates with orientation relationship with the decagonal phase, indicating a close structural similarity between the three phases. Gradual depletion of Y during solidification plays an important role in heterogeneous nucleation of decagonal and $Mg_4Zn_7$ phases from icosahedral and decagonal phases respectively.