• 한국주조공학회지
• /
• 제11권3호
• /
• pp.208-216
• /
• 1991

The solidification behavior of the squeeze cast composites of aluminum alloys reinforced with boron fiber($100{\mu}m$) and silicon carbide fibers($140{\mu}m$ and $15{\mu}m$) were investigated. Al-4.5wt%Cu and Al-l0wt%Mg were chosen for the matrix phase of the composites. In the squeeze cast specimen with high thermal difference between fiber and melt, the average secondary dendrite arm spacing(DAS) in reinforced alloy is smaller than that in unreinforced alloy. It was also observed that primary ${\alpha}$ and non-equilibrium eutectic, which seems to be penetrated and solidified at the final stage of the solidification of the matrix, are irregularly distributed around fibers. It is considered that cold fibers serve as heterogeneous nucleation site. While in the remelted and resolidified specimen without temperature difference, the DAS was not changed with reinforcement and microstructure reveals non-equilibrium eutectic with relatively uniform thickness around fibers. It might be evident the nucleation starts at interfiber region. Microsegregation decreases with the decrease in cooling rate and with reinforcement in the as-squeeze cast specimen. Al-10wt% Mg alloy shows less microsegregation than Al-4.5wt%Cu alloy.

• 소성∙가공
• /
• 제12권6호
• /
• pp.588-596
• /
• 2003

The relationships between evolution of microstructure and mechanical properties of porous Al-3Si-2Mg-2Cu alloy after the foaming and various heat treating were investigated. The foamed alloy having various densities were manufactured by powder compact foaming and heat treated. Then compression test was performed with deformation rate of 0.5/s. The ultimate compression strength was not changed after solution heat treatment but the flow curve after ultimate strength showed very smooth and uniform plateau region. This change of flow curve means that the deformation mechanism is altered from brittle fracture to ductile deformation and the energy absorption property of Al foam is dramatically improved. The improvement of energy absorption without any detriment of mechanical properties is due to that the very brittle precipitation like Al-Cu and Al-Mg was uniformly dissolved in Al matrix after solution heat treatment. And various mechanical properties of Al alloy porous material were improved by 40% with aging of $200^{\circ}C$ and 50min. These improvements are ascribe to the various fine precipitates like $\Omega$ and $\theta$'.

• 한국전자현미경학회:학술대회논문집
• /
• 한국현미경학회 2004년도 제35차 추계학술대회 및 제2회 HVEM 이용자 워크샵
• /
• pp.129-132
• /
• 2004

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.536-537
• /
• 2006

In the present work, the sintering behavior of high strength Al-5.6Zn-2.5Mg-1.6Cu (in wt.%) alloy compacts prepared from elemental powders was investigated. Microstructural evaluation was accompanied by XRD and DSC methods in order to determine the temperature and chemical composition of the liquid phases formed during sintering. It was found that three transient liquid phases are formed at 420, 439 and 450 $^{\circ}C$. Microstructural study revealed the progressive formation of sintered contacts due to the presence of the liquid phases, although the green compact expands as a result of the melt penetration along the grain boundaries. While Zn melts at ${\sim}420\;^{\circ}C$, the intermetallic phases formed between Al and Mg were found to be responsible for the formation of liquid phase and the dimensional change at higher temperatures.

• 한국주조공학회지
• /
• 제20권5호
• /
• pp.300-306
• /
• 2000

The objective of this work was to investigate the effects of SiC particle size(50, 100 ${\mu}m$) and additional elements such as Si, Cu and Ti on aging behavior in Al-5Mg-X(Si,Cu,Ti)/SiCp composites fabricated by pressureless infiltration method using hardness and wear test, scanning electron microscopy(SEM) and differential scanning calorimetry(DSC). The peak aging time in Al-5Mg-X(Si, Cu, Ti)/SiCp(50, 100 ${\mu}m$) composites is shorter than Al-5Mg-0.3Si alloy.The peak aging time of 50 ${\mu}m$ SiC particle reinforced Al-5Mg-X(Si,Cu,Ti) composites is shorter than those of 100 ${\mu}m$ SiC particle reinforced of Al-5Mg-X(Si,Cu,Ti) composites. The Al-5Mg-0.3Si-0.1Cu-0.1Ti/SiCp(50 ${\mu}m$) composites aged at $180^{\circ}C$ has higher hardness and better wear resistance than any other aged composite.The aging effect is promoted by the addition of Si and Cu in Al-5Mg/SiCp composites, so the wear resistance of Al-5Mg/SiCp composites with Si and Cu elements is enhanced by the aging treatment.

• 한국수소및신에너지학회논문집
• /
• 제10권4호
• /
• pp.225-232
• /
• 1999

Ni-MH 2차 전지의 음극재료로 사용되는 수소저장합금중 이론 방전용량이 가장 높은 $Mg_2Ni$를 기계적 합금법으로 제조하여 각종 첨가물의 첨가에 따른 전기화학적 특성을 조사하였다. $Mg_2Ni$는 고에너지 볼밀인 SPEX 8000을 이용하여 두가지 방법으로 제조하였다. 하나는 Mg, Ni 분말에 첨가물인 $AB_5$, $AB_2$계 수소저장합금과 Ni, Co, Cu를 첨가하여 12시간 볼밀링한 경우이고, 다른 하나는 먼저 Mg, Ni 분말을 1시간동안 볼밀링한 후 $300{\sim}400^{\circ}C$에서 열처리하여 $Mg_2Ni$를 제조한 후 여기에 첨가물을 10wt% 첨가하여 12 시간동안 볼밀할 경우이다. 이 볼밀링한 복합분말을 상온에서 $754tons/cm^2$의 압력으로 냉간압착하여 디스크 모양의 전극을 제조하였다. 실험결과 볼밀링 후 열처리를 거친 합금분말의 경우가 그렇지 않은 경우에 비해 전극의 방전용량이 높았으며, Ni을 첨가한 경우는 방전용량을 증가시키고 Co를 첨가한 경우는 싸이클 특성이 향상되었다. 특히 $Mg_2Ni$에 Ni을 10wt%를 첨가하여 12시간 볼밀한 경우 $Mg_2Ni$의 최대 방전용량은 546mAh/g.alloy으로 이론용량의 약 55%에 달했다.

• 한국주조공학회지
• /
• 제10권1호
• /
• pp.43-49
• /
• 1990

The influences of Cu and Mg addition on wear properties of SiC particulate reinforced Al-Si metal(alloy) matrix composites were investigated. Metal matrix composites were prepared by combination of compocasting and hot pressing techniques. The main results obtained are as follows : 1) The composite with Mg addition exhibits letter wear resistance than that with Cu addition. It is considered that Mg addition improved wettability of matal matrix composite by the strong segregation to the SiC / Al matrix interface. 2) After homogenization treatment, it was found that the interfacial segregation of Mg was predominant, while that of Cu was not detected. 3) The SiC / Al-11Si eutectic composite exhibits better wear resistance than the SiC / Al-6Si hypoeutectic composite does. 4) It seems that the increase in the amount of Mg addition affects on the uniform dispersion of SiC particulates, on the refinement of microstructure and on age hardening and these effects cause wear resistance improvement of composites.

• 열처리공학회지
• /
• 제10권2호
• /
• pp.81-92
• /
• 1997

The effect of alloying elements, precipitate size, its distribution, and dislocation substructure resulted from warm rolling or cold rolling in the superplastic Al-Mg alloy system was investigated. One of the major requirements for fine structure superplasticity is that the grain size should be very small. Fine grain structure is controlled by the dislocation substructure and the dynamic recrystallization during hot or warm working. The recovery of Al-Mg base alloys was constrained resulting in relatively high dislocation density when the alloys were warm rolled. In particular, Al-Mg-Zr alloy exhibited the smallest sub-grain size among Al-Mg alloys containing Mn, Cu, Zr as a third element. The Al-Mg-Mn alloy cold rolled 80% after hot rolling showed the maximun strain rate sensitivity exponent, m, of 0.75 under strain rate of $7.1{\times}10^{-4}/s$ at $500^{\circ}C$. The elongation of the alloys was limited in spite of high m values due to large dispersoids containing appreciable amount of Fe impurities.

• 열처리공학회지
• /
• 제4권2호
• /
• pp.38-46
• /
• 1991

Effects of aging treatment on the microstructures and microhardness of a rapidly solidified Al-Li-Cu-Mg-Zr alloy were investigated by differential scanning calorimetry(DSC) and transmission electron microscopy(TEM). The as-melt-spun ribbon was consisted of fine ${\delta}^{\prime}$ and icosahedral intermetallic compound which were precipitated in the matrix. Two exothermic peaks with the range of $120^{\circ}C-190^{\circ}C$ and $280^{\circ}C-344^{\circ}C$ corresponded to ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ precipitating reaction respectively, and two endothermic peaks with the range of $190^{\circ}C-280^{\circ}C$ and $344^{\circ}C-550^{\circ}C$ corresponded to dissolution of ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ respectively in DSC curves. Peak hardness value was obtained at $210^{\circ}C$ for 1 hr aging treatment.

• 한국재료학회지
• /
• 제8권8호
• /
• pp.672-677
• /
• 1998

오원계 AI-합금의 용융산화에 의한 $AI_2O_3$ 복합재료의 형성속도와 미세구조에 대하여 연구하였다. AI-1Mg-3Si-3Zn 합금과 AI-1Mg-3Si-5Zn합금에 Cu, Ni 각각을 1% 무게비로 첨가하였다. 각 오원계 합금은 1373K, 1473K에서 최대 20시간 동안 산화시켰으며, 산화속도는 무게증가 측정을 통하여 조사하였다. 산화층의거시적 형상과 미세구조를 광학현미경으로 관찰하였다. AI-1Mg-3Si-5Zn-1Cu 합금이 가장 우수한 산화거동을 보였으나, 산화층이 불균일하였다. 합금위에 $SiO_2$를 도포하였더니 산화속도가 증진되었으며, 균일하고 조직이 친밀한 산화층이 얻어졌다.