• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.165.1-165.1
• /
• 2016

Zn의 수요는 매년 증가하지만 매장량의 한계로 대체용 물질계가 개발이 필요한 시점이다. Zn보다 상대적으로 풍부하고 동일 두께의 Zn 코팅층과 비교하여 우수한 내식성을 보이는 Al과 Mg의 코팅층을 제작하여 Al-Mg 코팅 강판의 특성 분석 및 평가를 실시하였다. Al-Mg 코팅층은 99.99%의 Al, 99.9%의 Mg target을 사용하여 스퍼터링을 이용하여 냉연강판 위에 코팅하였다. 증발물질과 기판과의 거리는 7cm 이며, 기판은 세척을 실시한 후 클리닝 챔버에 장착하고 ~10-5 Torr 까지 진공배기를 실시하였다. 클리닝 챔버가 기본 압력까지 배기되면 아르곤 가스를 주입하고 기판 홀더에 -800 V의 직류 전압을 인가하여 약 30분간 글로우 방전 청정을 실시하였다. 기판의 청정이 끝나면 아르곤 가스를 차단하고 코팅 챔버로 시편을 이송 후 코팅층 성분의 구성형태에 따라 Al과 Mg을 코팅하였다. Al-Mg 코팅층은 $3{\mu}m$의 두께를 기준으로 Mg wt.%의 비율을 5% ~ 90%까지 변화시키며 코팅하였다. 그리고 후속 공정으로 질소 분위기 $400^{\circ}C$에서 10분간 열처리를 하였다. Al-Mg 코팅층을 주사전자현미경으로 관찰한 결과, 표면에서는 Al-Mg 코팅층에 존재하는 Mg 함량이 높아질수록 grain의 크기가 증가하였고 단면에서는 열처리 전의 치밀한 구조에서 열처리 후에는 주상구조 혹은 grain 구조가 선명해지는 것을 볼 수 있었으며 글로우방전분광기로 Al과 Mg의 성분 비율변화를 확인할 수 있었다. 또한 Al-Mg가 코팅된 강판을 염수분무시험을 통해서 내부식 특성을 확인하였다. Al-Mg 코팅 강판의 염수분무시험 결과, Mg 함량이 낮은 Al-Mg 코팅층은 열처리 후 뚜렷한 내식성 향상을 보였으며 Mg 조성 변화에 따라 일정한 경향성을 보였다. 하지만 Mg 함량이 높은 Al-Mg 코팅층은 열처리 후 급격한 내식성 저하와 함께 시편간의 편자가 커지는 것을 확인 할 수 있었다. 최적의 내식성을 보이는 Mg의 조성을 확인하기 위해서는 향후 보다 변별력이 높은 평가가 결과가 필요하다고 판단되어진다.

• Corrosion Science and Technology
• /
• v.23 no.2
• /
• pp.104-112
• /
• 2024

Al-Zn-Mg-Si alloy coatings have been developed to inhibit corrosion of cold rolled steel sheets, and an understanding of the alloy system helps prevent coating defects. We used a Bridgman furnace to characterise the nature and formation mechanisms of the phases present in the quaternary system with 0.4 wt% Fe. In the directional solidification experiments we imposed steep temperature gradients and varied the pull rate. After the samples were quenched in the furnace, detailed characterization of the samples was carried out by electron microscopy (SEM/EDS). From the dT/dt vs T plots of the cooling curves of the alloys, the solidification path was determined to be $Liquid{\longrightarrow[80]^{544-558}}{\alpha}-Al{\longrightarrow[80]^{453-459}}Al/Mg_2Si{\longrightarrow[80]^{371-374}}Al/Zn{\longrightarrow[80]^{331-333}}Zn/mgZn_2$. The formation mechanisms of the Mg and Zn containing phases and their morphology was discussed together with the effects of the cooling rate. Key findings include the lengthening of the mushy zone in directionally solidified samples remelted against a positive temperature gradient, as well as an enrichening of the α-Al phase by Zn through remelting. Mg₂Si and other Si based phases were observed to adopt a much finer faceted microstructure in favour of a script-like microstructure when exposed to the higher cooling rate of coolant quenching.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1017-1024
• /
• 2000

Effect of the microwave dielectric properties and the microstructure on a mole fraction(x=0.1~0.9) of (1-x)Mg$_2$SiO$_4$-xZnAl$_2$O$_4$ ceramics was investigated. When (1-x)Mg$_2$SiO$_4$-xZnAl$_2$O$_4$(x=0.1~0.9) ceramics were sintered at 130$0^{\circ}C$, 135$0^{\circ}C$ and 140$0^{\circ}C$ for 2hr, the microwave dielectric properties were obtained $\varepsilon$r=6.8~8.3, Q.f$_{0}$=36000~77600. On the other hand, the temperature coefficients of resonant frequency($\tau$$_{f}$) were obtained in the properties of -62ppm/$^{\circ}C$ to -49ppm/$^{\circ}C$. In order to adjust the temperature coefficient of resonant frequency($\tau$$_{f}$), CaTiO$_3$was added in (1-x)Mg$_2$SiO$_4$-xZnAl$_2$O$_4$ceramics. 0.7Mg$_2$SiO$_4$-0.2ZnAl$_2$O$_4$-0.1CaTiO$_3$ceramics sintered at 135$0^{\circ}C$ for 2hr showed the excellent microwave dielectric properties of $\varepsilon$r=7.7, Q.f$_{0}$=32000, and $\tau$$_{f}$=-7.9 ppm/$^{\circ}C$.EX>.>.EX>.

• Journal of Korea Foundry Society
• /
• v.32 no.1
• /
• pp.38-43
• /
• 2012

The effects of Mg and Cu amounts on the casting characteristics and tensile property of Al-Zn-Mg-Cu alloys were investigated for the development of high strength aluminium alloys for gravity mold casting. Increase of copper amounts in Al-6%Zn-3%Mgy% Cu alloys resulted in reduction of the fluidity of these alloys and had little effects on the tensile property of these alloys. Increase of magnesium amounts from 1.0wt% to 3.3wt% in Al-6%Zn-x%Mg-0.5%Cu alloys resulted in reduction of the elongation of these alloys from 12% to 3% and increase of the tensile strength of these alloys from 340MPa to 450MPa, but had little effects on the fluidity of these alloys.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.139-139
• /
• 2017

최근 환경오염 문제로 인한 연비 규제 강화 속도가 빨라지고 있으며 이에 따른 연비 향상 기술이 크게 대두 되고 있다. 연비 향상 기술 중 경량화 방안소재로 알루미늄(Al), 마그네슘(Mg) 등의 비철금속을 주로 사용하고 있으며, 이중 알루미늄은 다른 경량화 금속소재보다 우수한 경쟁력을 가지고 있다. 하지만 경제적인 측면에서 철 대비 비용적인 어려움을 가지고 있고 용접성이 떨어지기 때문에, 자동차 부품의 일부만 알루미늄 소재를 선택하여 사용하고 있는 실정이며 알루미늄의 높은 이온화 경향으로 인해 기존 자동차 철강 소재와 접촉 시 쉽게 부식되는 단점을 가지고 있다. 이러한 문제점을 해결하기 위해서는 알루미늄의 금속원소를 첨가하는 연구가 지속적으로 개발 되고 있다. 알루미늄 합금에서 마그네슘의 첨가는 좋은 용접성과 내식성, 강도를 향상시킨다. 하지만 3%이상의 마그네슘 첨가는 입계에 ${\beta}(Al_xMg_y)$석출상이 석출되게 되며, 입계에 연속적으로 형성된 ${\beta}(Al_xMg_y)$석출상은 응력 부식 균열 (Stress corrsion cracking)과 입계 부식(Intergranular corrosion)을 야기하는 결과를 가져온다고 알려져 있다. 이 문제를 해결하기 위해 Al 5000계열 합금의 Zn의 첨가를 통해 ${\tau}(Al_xMg_yZn_z)$을 입계에 석출시켜서 입계에 ${\beta}(Al_xMg_y)$상의 석출을 방지함으로써 내식성을 향상시키거나 Al 5000계열 합금의 열처리를 통해 ${\beta}(Al_xMg_y)$석출상을 고용시킴으로써 응력부식균열의 발생을 억제하는 연구도 있다. 하지만 열처리 후 Polarization test를 이용한 내식성 연구는 잘 안 알려져 있다. 따라서 이번 연구에서는 Al5000계열의 주조한 합금을 DSC분석을 통하여 ${\beta}(Al_xMg_y)$석출상의 고용 온도가 약 $470^{\circ}C$라는 것을 확인한 후, 실온에서 $100^{\circ}C/hr$으로 가열하고 조건에 따라 $450^{\circ}C$에서 3시간, 6시간, 12시간, 24시간, 30시간 항온 유지시킨 후 공냉을 진행하였다. 열처리를 마친 시편은 에폭시를 이용하여 마운팅 하였으며, 시편표면을 2000#까지 연마 후 증류수로 세척한 다음 질소를 이용하여 건조 후 분극 시험을 진행하였다. 3.5wt% NaCl 용액에서 분극 곡선을 통해 부식거동을 확인한 결과 24시간까지 시간이 증가 할수록 내식성이 우수해지는 것을 확인하였으며, 추가적으로 조직사진, SEM & EDS 분석과 XRD, TEM 분석을 통해 내식성은 입계에 존재하는 Mg의 조성이 감소하게 되면 내식성이 향상되는 것을 관찰하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.5
• /
• pp.285-297
• /
• 2023

The effects of aging treatment sequence, specifically pre-aging and post-aging, on the microstructure and mechanical properties of Al-Zn-Mg-Cu aluminum alloys has been studied in comparison to symmetrically rolled specimens. In symmetrically rolled specimens, a straight-band precipitation distribution was observed, whereas asymmetrically rolled specimens exhibited a curved-band microstructure of fine precipitates. Notably, the asymmetrically rolled specimens displayed higher strengths. In the case of post-aging, the aging process occurred after rolling, and the dislocations generated during rolling acted as nucleation sites for precipitates during aging. This resulted in the formation of fine precipitates, contributing to improved mechanical properties compared to symmetric rolling. To enhance strength of the Al-Zn-Mg-Cu aluminum alloys, asymmetric rolling proves to be more effective than symmetric rolling, with post-aging showing greater efficacy than pre-aging.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.542-549
• /
• 2020

Effects of Sc addition on microstructure, electrical conductivity, thermal conductivity and mechanical properties of the as-cast and as-extruded Al-2Zn-1Cu-0.3Mg-xSc (x = 0, 0.25, 0.5 wt%) alloys are investigated. The average grain size of the as-cast Al-2Zn-1Cu-0.3Mg alloy is 2,334 ㎛; however, this value drops to 914 and 529 ㎛ with addition of Sc element at 0.25 wt% and 0.5 wt%, respectively. This grain refinement is due to primary Al₃Sc phase forming during solidification. The as-extruded Al-2Zn-1Cu-0.3Mg alloy has a recrystallization structure consisting of almost equiaxed grains. However, the as-extruded Sc-containing alloys consist of grains that are extremely elongated in the extrusion direction. In addition, it is found that the proportion of low-angle grain boundaries below 15 degree is dominant. This is because the addition of Sc results in the formation of coherent and nano-scale Al₃Sc phases during hot extrusion, inhibiting the process of recrystallization and improving the strength by pinning of dislocations and the formation of subgrain boundaries. The maximum values of the yield and tensile strength are 126 MPa and 215 MPa for the as-extruded Al-2Zn-1Cu-0.3Mg-0.25Sc alloy, respectively. The increase in strength is probably due to the existence of nano-scale Al₃Sc precipitates and dense Al₂Cu phases. Thermal conductivity of the as-cast Al-2Zn-1Cu-0.3Mg-xSc alloy is reduced to 204, 187 and 183 W/MK by additions of elemental Sc of 0, 0.25 and 0.5 wt%, respectively. On the other hand, the thermal conductivity of the as-extruded Al-2Zn-1Cu-0.3Mg-xSc alloy is about 200 W/Mk regardless of the content of Sc. This is because of the formation of coherent Al₃Sc phase, which decreases Sc content and causes extremely high electrical resistivity.

• Journal of Korea Foundry Society
• /
• v.24 no.3
• /
• pp.138-144
• /
• 2004

Effects of alloying elements such as Si, Mn, Zn on the fluidity and mechanical properties of high ductility Al-Mg based alloys were investigated. The fluidity of alloys was evaluated using a vacuum suction fluidity test, and Si addition was observed to increase the fluidity of AI-Mg binary alloys substantially while Zn somewhat decreased the fluidity. However, both the strength and ductility were significantly deteriorated by the Si additions. It was observed that a small amount of Mn addition to Al-Mg alloy increased the tensile strength effectively without losing much ductility but the effect of Zn addition on the strength was relatively small.

• Journal of Korea Foundry Society
• /
• v.22 no.2
• /
• pp.82-88
• /
• 2002

Al-5.5Zn-2.5Mg-l.5Cu semi-solid slurry was prepared by cooling the liquid metal with a low superheat to a solid and liquid co-existing temperature. Relatively round solid particles could be obtained in the slurry through the simple process. The prepared slurry was deformed into the metallic mold by a press and the mechanical properties of obtained specimens were investigated. Mold filling ability of the alloy slurry was also investigated and compared with that of A356 alloy. Al-Zn-Mg-Cu alloy showed lower mold filling ability than A356 alloy probably because small amount of eutectic phase is present and the heat of fusion generated during solidification is smaller than that of A356 alloy.

• Journal of the Korean Ceramic Society
• /
• v.29 no.11
• /
• pp.888-892
• /
• 1992

The chemically induced grain-boundary migration has been studied in MgAl2O4 spinel under ZnO atmosphere. MgAl2O4 compacts been prepared by sintering powder mixture of Al2O3 and MgO at 1$600^{\circ}C$ for 60 h in air. The sintered MgAl2O4 has been heat-treated at 150$0^{\circ}C$ in a ZnO atmosphere. During the heat-treatment grain boundaries have become curved or faceted, and the total area of grain boundaries have increased. In the migrated region, the ZnO content is higher by 6 wt% than that in other regions, indicating that the migration was induced by addition of ZnO. In some shrinking grains, the faceted planes of different grain boundaries for the same grain are parallel to each other. This result provide an experimental support for the coherency strain energy in diffusion layer of the shrinking grain as being the major driving force. Calculated coherency strain energy of MgAl2O4 shows the maximum at {111} planes and the minimum at {100} planes. Although the minimum surface energy is at {111} planes, the faceted moving boundaries are expected to be {100} planes because of lowest driving force for the grain-boundary migration.