• 한국환경보건학회지
• /
• 제22권1호
• /
• pp.36-44
• /
• 1996

A comparison was made of two detection methods(UV absorbence detection and fluorescence detection with pre-column derivatization, with trifluoroacetic acid) coupled with HPLC for the simultaneous determination of aflatoxin $B_1, B_2, G_1$ and $G_2$. A good separation of the four aflatoxins was achieved on a reversed-phase $C_{18}$ column (30 cm x 3.9 mm) with methanol-acetonitrile-water(20+20+60) for absorbence detection or acetonitrile-water(25+75) for fluorescence detection at the flow rate of 1.0 ml/min. The calibration graphs were linear over the ranges 100 ppb-1 ppm for $B_1/G_1$ and 30~300 ppb for $B_2/G_1$ with absorbence detection, and 1~500 ppb for $B_1/G_1$ and 0.3~150 ppb for $B_2/G_2$ with fluorescence detection. The correlation coefficients were greater than 0.94 and 0.99 for absorbance detection and for fluorescence detection, respectively. The detection limit was 100 ng for $B_1/G_1$ and 30 ng for $B_2/G_2$ with absorbence detection, and 1 ng for $B_1/G_1$ and 0.3 ng for $B_2/G_2$ with fluorescence detection. Recovery rates of aflatoxin $B_1, B_2, G_1$ and $G_2$ added to yeast-extract sucrose broth medium were 66.6%, 59.4%, 67.5% and 59.2%, respectively, for absorbence detection and 82.9%, 71.5%, 80.0% and 69.3%, respectively, for fluorescence detection. The four aflatoxins in culture medium were quantitatively detected by the two methods. The aflatoxins in the rice sample were not detected the absorbence detection method, but were below 10 ppb using the fluorescence detection method. Analysis of aflatoxins by both the absorbence and fluorescence methods coupled with HPLC showed acceptable linearity and good recovery. The absorbence detection was less timeconsuming and safer for treatment. The fluorescence detection was more elective and sensitive though elevated $B_1$ and $G_1$ contents were determined from the TFA-induced conversion of $B_1$ to $B_{2a}$ and $G_1$ to $G_{2a}$.

• 한국수소및신에너지학회논문집
• /
• 제12권4호
• /
• pp.277-285
• /
• 2001

본 논문은 연료전지 자동차용 10kWe급 정제일체형 메탄올개질기에 대한 연구결과이다. 이 개질기에서는 메탄올이 수증기와 반응하켜 수소를 포함한 혼합가스로 개질되고, 그 혼합가스는 다시 Palladium 합금막을 통하여 순수한 수소로 분리된다. 정제되고 남은 폐 가스중 가연성분들은 wire-mesh 형태의 연소촉매상에서 연소되어 개질반응에 필요한 열을 직접 공급함으로써 높은 메탄올 전환율, 고품질의 수소생산, 그리고 높은 시스템 열효율을 가능하게 한다. 동시에 이러한 개질, 분리 및 연소반응이 하나의 반응기에서 일어나 전체 시스템이 소형화될 수 있으며 운전이 용이한 장점도 있다. 본 연구팀에서 개발한 10kWe급 시스템은 운전연구를 통하여 수소생산량은 $8.2Nm^3/hr$ (10kWe급), 수소순도 99.999% 이상, CO 농도 5 ppm 미만, 총합열효율 81%, 초기기동 소요시간 20분, 부하변동웅답 1 분 이내를 달성했으며, 장처의 크기와 무게는 각각 16 L, 25 kg 이다.

• 한국결정성장학회지
• /
• 제5권3호
• /
• pp.223-232
• /
• 1995

Urea($(NH_2)_2CO$) 및 THAMP(Tris(hydroxymethyl)aminomethane phosphate) 유기 단결정은 레이저의 파장변환소자등의 응용에 유용한 새로운 유기 비선형 광학재료(NLO)이다. 온도하강법과 온도차법을 이용하여 urea와 THAMP 유기 단결정의 육성을 시도하였으며 이들 방법에 따른 육성조건을 확립하였다. Urea의 용매로는 용해도의 측정을 통하여 메탄올이 가장 적합하였으며, 용해도에 대한 온도계수는 posotive였으며, 용해열은 - 2.58 kcal/mol이었다. 육성된 urea 결정은 z축의 성장이 지배적이었고, z축의 성장제어와 x, y축의 성장을 위하여 $NH_4_H_2PO_4$, KCL, $H_3PO_4$, $CaCl_2{\cdot}2H_2O$, $C_2H_5OH$의 첨가제를 사용하여 z축의 성장제어와 x, y축의 성장을 증진시켰다. THAM과 $H_3PO_4$의 화학 양론적 혼합비 1 : 1의 몰비로부터 양질의 THAMP 유기 단결정을 육성하였고 용해도에 대한 온도계수는 positive였으며, 용해열은 - 1.70 kcal/mol이었다.

• 생약학회지
• /
• 제40권4호
• /
• pp.298-302
• /
• 2009

Samultang is one of traditional medicine composed of Paeonia lactiflora, Angelica gigas, Rehmannia glutinosa and Cnidium officinale. To develop simultaneous determination of paeoniflorin, decursin and 5-HMF in Samultang, a high performance liquid chromatography with diode array detector was used. To separate three marker components, Dionex $C_{18}$ column (5 ${\mu}m$, 120 ${\AA}$, 4.6 mm${\times}$150 mm) was used with a gradient elution system of water and methanol. UV wavelength of detector set at 230 nm and 280 nm. This method was validated by linearity, precision test and recovery test. Calibration curves of three standard components were showed good linear regression ($R^2$>0.9973). LOD and LOQ ranged from 0.08 ${\mu}g$/ml to 0.38 ${\mu}g$/ml and 0.25 ${\mu}g$/ml to 1.16 ${\mu}g$/ml, respectively. The relative standard deviations (RSDs) of data of the inter-day and intra-day experiments were less than 0.54% and 0.89%, respectively. The measured results of recovery test were varied from 93.36 to 107.79 with RSD values 0.01~1.45%. The established method was applied for separation of bio-conversion Samultang sample and compared with control sample.

• Korean Chemical Engineering Research
• /
• 제47권4호
• /
• pp.446-452
• /
• 2009

최근 청정대체에너지로 각광을 받고 있는 dimethyl ether(DME)를 천연가스를 이용하여 직접 생산하는 1단계법의 고정층 촉매 반응기를 모사하였다. 1단계법의 고정층 반응기의 경우, 발열 반응인 메탄올 합성반응과 메탄올 탈수 반응이 동시에 일어나기 때문에 촉매의 비활성화를 일으킬 수 있는 hot spot의 발생을 막는 것이 가장 중요하다. 따라서 향후 상용공정에 적용 가능한 향류 냉각방식(count-current cooling system)과 포화액체 풀비등 방식(pool boiling system)을 적용하여 반응기 거동을 모사하고 이를 비교하였다. CO 전환율과 DME 생산성 면에서 향류 냉각방식이 더 효과적이었다. 하지만 포화비등액체 풀비등 방식이 더 작은 온도 범위에서 운전되어 hot spot(국소 고온점)의 가능성을 낮추고 더 안정적인 반응기 운전범위를 확보할 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제29권1호
• /
• pp.1-10
• /
• 2018

The amount of biogas increases as the amount of organic waste increases. Recently, biogas from organic waste have been made much efforts to utilize as a energy. In particular, the concentration of $CH_4$ and $CO_2$ generated from sewage sludge and livestock manure treatment are 60-70% and 30-35%, and $CH_4$ and $CO_2$ generated from food wastes are 60-80% and 20-40%. In case of landfill gas, $CH_4$ and $CO_2$ have a concentration of 40-60% and 40-60% respectively. Therefore, in order to use the biogas more widely, it is necessary to convert the biogas to methanol, LNG or DME. In this study, experiments were conducted to produce hydrogen and carbon monoxide through various biogas reforming reactions on $Ni/Ce-ZrO_2/Al2O3$ catalysts. The experiment of synthetic gas synthesis was carried out on a wide concentrations of methane and carbon dioxide, which were the major constituents of biogas from various organic wastes. The effect of $(O_2+CO_2)/CH_4$ (=R') on the yields of hydrogen and carbon monoxide, the conversion rate of methane and carbon dioxide was investigated. Also simulation for syngas synthesis on the $CO_2$ reforming of $CH_4$ was computed by employing total Gibbs free energy minimization method using PRO/II simulator, and compared with the experimental results on wet and dry reforming reaction of biogas.

• 대한한방내과학회지
• /
• 제21권4호
• /
• pp.597-604
• /
• 2000

Objective : his study was carried out to investigate the effect of Dansameum (DS) on the gastrohemorrhagic lesion induced by ammonia in rats. Methods : Rats were pretreated with DS extract 25 mg/kg for 10 days and then were given amonia through gastric tube. The animals were killed 1 hr after amonia treatment. Results : DS extract siginificantly reduced the gastrohemorrhagic lesion score, the gastric lipid peroxide level, the gastric urease activity, the gastric myeloperoxidase activity, the gastric acid phosphatase activity, xanthine oxidase activity and type conversion, and increased the gastric glutathione level considerably. In photomicrographs of stomach tissue in rat, we could see the gastrohemorrhagic lesion induced clearly. conclusions : These results suggest that DS extract may be effective in peptic ulcer.

• 한국수소및신에너지학회논문집
• /
• 제25권2호
• /
• pp.105-113
• /
• 2014

Performance tests on $Ni/Ce-ZrO_2/Al_2O_3$ catalysts with additives (MgO, $La_2O_3$) were investigated in the combined reforming processes (SCR, ATR, TRM) in order to produce hydrogen and carbon monoxide (it is called "syngas".). The catalyst characterization was conducted using the BET surface analyzer, X-ray diffraction (XRD), SEM, TPR and TGA. The combined reforming process was developed to adjust the syngas ratio depending on the synthetic fuel (methanol, DME and GTL) manufacturing processes. Ni-based catalysts supported on alumina has been generally recommended as a combined reforming reaction catalyst. It was found that both free NiO and complexed NiO species were responsible for the catalytic activity in the combined reforming of methane conversion, and the $Ce-ZrO_2$ binary support employed had improved the oxygen storage capacity and thermal stability. The additives, MgO and $La_2O_3$, also seemed to play an important role to prevent the formation of the carbon deposition over the catalysts. The experimental results were compared with the equilibrium data using a commercial simulation tool (PRO/II).

• 한국재료학회지
• /
• 제9권2호
• /
• pp.117-123
• /
• 1999

삼차원적 골격구조를 가지며 세공의 크기와 산성도가 유사한 SAPO-44, SAPO-34(CHA type), SAPO-17(ERI type), 그리고 1차원적 고격구조를 가진 ZSM-23(MTT type) 촉매재료를 합성하고, 메탄올 전환방응에 있어서의 촉매적 성능을 비교 검토하였다. 이들의 산성도 세기는 SAPO-44>SAPO-34>SAPO-17>ZSM-23 순으로 나타났다. 메탄올 전환반응을 비교한 결과, 삼차원적 골격구조를 가지고 있는 SAPO-34와 SAPO-44에서 높은 에티렌 선택성이 얻어졌으며, 특히 Ni을 골격내에 도입시켰을 때 그 선택율은 더욱 증가하였다. 반면에 1차원적 골격구조를 가지고 있는 ZSM-23에서는 입체적 형상선택성의 감소로 올레핀보다는 파라핀의 선택율이 우세하였다.

• 한국미생물·생명공학회지
• /
• 제48권4호
• /
• pp.491-505
• /
• 2020

A newly isolated strain, Proteus vulgaris OR34, from olive mill waste was found to secrete an alkaline extracellular lipase at 11 U·ml-1 when cultivated on an optimized liquid medium. This lipase was purified 94.64-fold with a total yield of 9.11% and its maximal specific activity was shown to be 3232.58 and 1777.92 U·mg-1 when evaluated using the pH-stat technique at 55℃ and pH 9 and Tributyrin TC4 or olive oil as the substrate. The molecular mass of the pure OR34 lipase was estimated to be around 31 kDa, as revealed by SDS-PAGE and its substrate specificity was investigated using a variety of triglycerides. This assay revealed that OR34 lipase preferred short and medium chain fatty acids. In addition, this lipase was stable in the presence of high concentrations of bile salt (NaDC) and calcium ions appear not to be necessary for its activity. This lipase was inhibited by THL (Orlistat) which confirmed its identity as a serine enzyme. In addition, the immobilization of OR34 lipase by adsorption onto calcium carbonate increased its stability at higher temperatures and within a larger pH range. The immobilized lipase exhibited a high tolerance to organic solvents and retained 60% of its activity after 10 months of storage at 4℃. Finally, the OR34 lipase was applied in biodiesel synthesis via oleic acid mediated esterification of methanol when using hexane as solvent. The best conversion yield (67%) was obtained at 12 h and 40℃ using the immobilized enzyme and this enzyme could be reused for six cycles with the same efficiency.