• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2013

Pneumatic cylinders are widely used to actuators in automatic equipments because they are relatively inexpensive, simple to install and maintain, offer robust design and operation, are available in a wide range of standard sizes and design alternatives. This paper presents a comparative study among the dynamic characteristics of meter-out and meter-in speed control of pneumatic cushion cylinders with a relief valve type cushion mechanism. Because of the nonlinear differential equations and a requirement for simultaneous iterative solution in a mathematical model of a double acting pneumatic cushion cylinder, a computer simulation is carried out to investigate pressure, temperature, mass flow rate in cushion chamber and displacement and velocity time histories of piston under various operating conditions. It is found that the piston velocity and pressure response in meter-in speed control are more oscillatory than with meter-out those when pneumatic cushion cylinders are driven at a high-speed. In meter-out speed control, the effective area of the flow control valve is larger than that of meter-in, and the supply pressure has to be much higher than the pressure required to move the load because it has also to overcome the back pressure in cushion chamber.

• 드라이브 ㆍ 컨트롤
• /
• 제13권4호
• /
• pp.7-13
• /
• 2016

This paper presents the meter-out and meter-in speed control characteristics of a pneumatic cylinder with relief valve type cushion device. The piston displacement and velocity are measured to investigate high speed driving performance with variation of the pressure setting in relief valve, air supply pressure, load mass, the supply and exhaust flow rate from the cylinder. Also, the internal pressures and temperatures driving pressure and cushion chamber are measured. The piston displacements and velocities of meter-out and meter-in control are compared experimentally determined data. A comparison experimental data meter-out and meter-in control show that a relief valve type cushion device is suitable for high speed pneumatic cylinders. The desired response characteristics of piston displacement and velocity are satisfactory adjust the pressure setting of a relief valve with varying system parameters such as air supply pressure, load mass and controlled flow rate.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1552-1564
• /
• 2002

Meter-in, meter-out and bleed-off circuits are widely utilized in order to adjust the speed of a hydraulic actuator by using a flow control valve and in order to regulate the pressure of a hydraulic volume by using a simple on-off valve. In these circuits, a relief valve serves either to maintain constant system pressure or to protect the system from over-pressure loading. The relief valve of a bleed-off circuit is the second case frequently undergoing on-off action during operation. It makes the analysis of the pressure control characteristics of the circuit highly difficult. In this paper, steady-state flow rate, pressure, heat loss and efficiency of the three circuits are reexamined and basic experiments far obtaining the characteristics of a pump and relief valve are conducted. Finally, simple empirical first-order dynamic models of decreasing and increasing pressure were separately proposed and verified by comparison with experiment. As the result, the basis for the theoretical analysis of the pressure control characteristics of a bleed-off circuit using a simple on-off valve is established.

• 융합신호처리학회논문지
• /
• 제13권1호
• /
• pp.56-62
• /
• 2012

이 논문은 매트랩/시뮬링크에서 도입한 TI 2000 DSP 라이브러리를 위한 임베디드 타켓을 사용하여 직류 모터 시스템에 대한 속도 제어기를 설계하고 구현하였다. 속도 제이기는 매트랩/시뮬링크 프로그램을 사용하여 쉽게 설계하고 구현할 수 있다. 모터 속도의 궤환은 속도 감지기로 엔코드와 펄스미터를 사용하여 eZdsp F2812 의 A/D 변환기를 통하여 처리하였다. 제어기의 실시간 프로그램은 시뮬링크를 사용하여 그렸고, P 제어기, PID 제어기 그리고 매개변수 추정 을 기반 적응제어기의 변환된 프로그램 코드는 Realsys eZdsp 2812 보드로 다운로드하였다. 그리고 실험을 통하여 구현된 제어기들의 속도응답을 확인하였다. 제어대상이 변경되었을 때에도 제어기를 쉽게 설계 및 구현하는 방법을 연구했다.

• 연구논문집
• /
• 통권27호
• /
• pp.153-166
• /
• 1997

In industry pneumatic control system has become a important means to obtain automation because of its simplicity, fast speed and low cost. However Due to of the compressibility of air and damping friction between moving parts, it is difficult to achieve high speed driving, accurate positioning and stopping without overshoot in one pneumatic control system. This paper describes the dynamic behaviors of pneumatic linear actuator. The results will be very useful in the prediction of actuated dynamics and for the manufacturers to improve the techniques in their redesign and get better performance. Also, the experimental data is very important for the dynamic simulation and theoretical analysis.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.24-30
• /
• 2013

This paper studies the comparative analysis on two different internal cushion devices (the types of needle and relief valve) used to absorb the energy which is generated when the pneumatic cylinder moves with the load at meter-out speed control system. The effect at varying the piston velocity under same driving condition is mainly investigated. The simulation results on pressure in the cushion chamber and the dynamic behavior of the relief valve type cushion device are compared with the needle valve type. Design and performance are improved with the cushion configuration of better quality at high-speed pneumatic cylinder. Based on the relation between absorbed energy and impact energy at cushion process, cushion performance at pneumatic cylinder is evaluated.

• 한국지반환경공학회 논문집
• /
• 제13권1호
• /
• pp.63-74
• /
• 2012

국내에서 그라우팅은 대부분 전문성 있는 지식이나 이론적인 연구에 의한 방법이 아닌 경험적인 방법에 의해 설계되고 있다. 따라서, 본 연구에서는 그라우팅이 적용되는 건설현장에서 자동화 그라우팅 기법의 품질관리기술과 방법에 대한 것을 논의하고자 한다. 연구결과, 제한적인 물주입시험에 의한 최적주입압 결정과 관련된 방법은 그라우팅 전.후에 대한 평가만이 가능한 것으로 나타났으며, 그라우팅재료가 지반내에서 확산하는 동안 주입압력(p)~주입속도(q)~침투시간(t) 차트 분석을 통해 주입압, 주입속도, 침투시간의 특성을 평가할 경우 그라우트 압력에 의한 지반의 파쇄를 방지할 수 있을 것으로 나타났다. 주입압력(p), 주입속도(q)와 침투시간(t) 곡선을 분석하여 적합한 값을 도출하면 효과적인 설계를 수행할 수 있다. 본 차트분석기법은 기존의 종이롤에 기록되어 지는 주입압력(p)과 주입속도(q)를 정리하여 관리할 수 있으며, 통합유량계는 정확한 수량을 기록할 수 있으나 기록된 주입압력은 초기, 중급 및 최종 지점에 따라 다르게 나타나므로, 통합유량계 및 그라우팅 대상 지반의 특성의 상관관계가 규명되는 것이 바람직한 것으로 사료된다, 본 연구에서 제안된 자동화 그라우팅 기법은 주입압력과 그라우팅 대상 지반의 특성간의 신뢰성 있는 상관관계를 설명할 수 있으며, 이를 활용한 그라우팅 품질관리 기술을 발전시킬 것으로 기대된다.

• 대한토목학회논문집
• /
• 제38권5호
• /
• pp.751-760
• /
• 2018

현재 다짐공사는 작업자가 정해진 다짐횟수, 두께, 속도, 진동여부 등을 자신의 경험에 의해 개별적으로 판단하고 감독자의 육안 검사에 의해 다짐공사의 품질측정이 이루어지고 있으며, 작업 후 대표성이 떨어지는 재래식 다짐강도 측정방법인 일점시험(Spot test)을 통하여 후속 단계의 작업을 진행하고 있는 실정이다. 따라서 다짐작업 결과에 대한 정량적 확인이 불가능하며, 시공부실로 인한 문제점이 제기될 가능성이 상존하고 있다. 본 연구에서는 여러 가지 시험조건에서 실제 현장규모로 다짐을 수행한 후 연속 다짐강도 측정 방법과 재래식 다짐강도 측정 방법과의 비교를 통해 연속 다짐강도 측정 방법의 사용 타당성을 입증하였다. 타당성 입증은 연속 다짐강도 측정방법인 GPS (Global Positioning System)와 가속도계로 구성된 IC (Intelligent Compaction) 롤러의 CMV (Compaction Meter Value)를 분석하는데 있으며, 입증된 결과를 토대로 일점시험을 배제한 현장 전 범위 품질확인이 가능하다. 품질 확인은 본 연구에서 개발한 다짐공사 관제프로그램에 시각화되며, 이를 통해 현장관리자는 다짐작업과 동시에 실시간 품질 모니터링이 가능하다.

• 한국가시화정보학회지
• /
• 제7권2호
• /
• pp.64-71
• /
• 2010

The flow and noise characteristics of wake behind wind-turbine blades have been investigated experimentally using a two-frame particle image velocimetry (PIV) technique. Experiments were carried out in a POSTECH subsonic large wind-tunnel ($1.8^W{\times}1.5^H{\times}4.3^L\;m^3$) with KBP-750D (3-blade type) wind-turbine model at a freestream velocity of $U_o\;=\;15\;m/s$ and a tip speed ratio $\lambda\;=\;6.14$ (2933 rpm). The wind-turbine blades are connected to an AC servo motor, brake, encoder and torque meter to control the rotational speed and to extract a synchronization signal for PIV measurements. The wake flow was measured at four azimuth angles ($\phi\;=\;0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$) of the wind-turbine blade. The dominant flow structure of the wake is large-scale tip vortices. The turbulent statistics such as turbulent intensity are weakened as the flow goes downstream due to turbulent dissipation. The dominant peak frequency of the noise signal is identical to the rotation frequency of blades. The noise seems to be mainly induced by the tip vortices.

• 연구논문집
• /
• 통권28호
• /
• pp.73-87
• /
• 1998

A pneumatic control system of compressed air as a working fluid has a variety of advantages such as low price, high respondence, non-explosion and good control performance and thus has many applications in the field of automobile, electronic and semiconductor industry. However, it has a difficulty in contolling a precise position due to quick response of system and compressibility of working fluid and. in particular, shock stress may occur due to an external load, resulting in fracture of a cylinder cap unless cushion device is equipped in the linear actuator. To avoid this, a cushion device should be installed for damping effect of the external load and the supply pressure as well as for decreasing shock stress and vibration caused by high speed rotation. Previous studies include dimensionless analyses and computer simulations of cushion capability and experiments of horizontally-mounted cylinder performances. A new attempt is experimentally made in this study using a vertically-mounted cylinder under an operation condition of 4, 5 and 6 (bar) as supply pressure and 40, 70 and 100 (kgf) as external load. It turns out that the cushion pressure is mainly a function of the external load rather than the supply pressure. The cushion characteristics was also revealed in the meter-in circuit.