• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.1-8
• /
• 2003

In general, the microstructure in thin films was known to evolve in similar manner according to the energy striking the condensing film at similar homologous temperature, Th for the materials of the same crystal structure. The fundamental factors affecting particle energy are a function of processing parameters such as working pressure, bias voltage, target/sputtering gas mass ratio, cathode shape, and substrate orientation. In this study, Al, Cu, Pt films of the same crystal structure of face centered cubic (FCC) have been prepared under various processing parameters. The influence of processing variables on the microstructures and residual stress states in the films has been studied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.268.1-268.1
• /
• 2013

Immobilization of conducting nanoparticles on a nanogap comprising two electrodes spaced at a distance comparable to the particle size can be used as a simple and sensitive method of detecting the particles. In this work, we have examined the performance of the nanogap devices in the measurement of metallic nanoparticles, particularly gold nanoparticles (Au NPs). Detection of pM-level Au NPs in an aqueous suspension was quite straightforward irrespective of the existence of non-conducting materials. Speed of detection or the time necessary for the completion of the measurement, however, was strongly dependent upon the immobilization process. Active trapping process was found to be much more efficient and also effective in the detection of nanoparticles than its passive counterpart.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.627-630
• /
• 1995

BaM films have a lot of advantage of chemical stability and mechanical stability as compared with a metallic thin film. In this paper, (Ba.Pb)M films have been prepared by using dc magnetron sputtering system and the dependences of their crystallographic characteristics and magnetic properties on oxygen pressure($Po_{2}$) were studied. The films prepared at $Po_{2}$ of around 0.02mTorr exhibit a fine particle-like structure and ${\Delta}{\theta}_{50}$ is as small as $1^{\circ}$. $Hc_{\bot},\;Hc_{//}$ and Ms of (Ba.Pb)M films are 700-800Oe, 200Oe and 180-230emu/cc, respectively.

• Journal of Powder Materials
• /
• v.23 no.3
• /
• pp.240-246
• /
• 2016

In order to improve the high-temperature oxidation stability, sintered 434L stainless steel is studied, focusing on the effect of the addition of metallic oxides to form stable oxide films on the inner particle surface. The green compacts of Fecralloy powder or amorphous silica are added on STS434L and oxidized at $950^{\circ}C$ up to 210 h. The weight change ratio of 434L with amorphous silica is higher than that of 434L mixed with Fecralloy, and the weight increase follows a parabolic law, which implies that the oxide film grows according to oxide diffusion through the densely formed oxide film. In the case of 434L mixed with Fecralloy, the elements in the matrix diffuse through the grain boundaries and form $Al_2O_3$ and Fe-Cr oxides. Stable high temperature corrosion resistance and electrical resistivity are obtained for STS434L mixed with Fecralloy.

• Journal of Environmental Science International
• /
• v.20 no.1
• /
• pp.147-153
• /
• 2011

The objectives of this study were to investigate the seasonal characteristics of metallic and ion elements of $PM_{10}$(Particulate matter with aerodynamic diameter ${\leq}10\;{\mu}m$) and the effects of vessels exhaust emission from ships harboring in Busan City. The $PM_{10}$ samples were collected from January 2010 to October 2010 at Dongsam-dong(coastal area), in Busan City. The particulate matters were analyzed for major water soluble ionic components and metals. The ranges of the $PM_{10}$ mass concentrations were from 29.8 ${\mu}g/m^3$ to 47.0 ${\mu}g/m^3$ in Dongsam-dong. The $PM_{10}$ mass concentrations in Dongsam-dong are very similar to Gwangbok-dong during same sampling periods. These results were understood by the effects of the shipping source emitted from ships anchoraging and running. The concentrations of water-soluble ions and metals in the $PM_{10}$ had a level of as high as the order of $SO_4^{2-}$>$NO_3^-$>$Cl^-$ and $NH_4^+$>$Na^+$>$Ca^{2+}$>$K^+$>$Mg^{2+}$, respectively. The correlation coefficients($R^2$) for $SO_4^{2-}/PM_{10}$ and $NH_4^+/PM_{10}$ of were 0.7446 and 0.7784, respectively, and it showed the high correlation with each other.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.199-203
• /
• 2002

To investigate an effect of sintering atmosphere on microstructure and properties of metallic particle dispersed ceramic based composites, the powder mixtures of $Al_2O_3$/Fe-Ni, synthesized by chemical solution process, were hot-pressed under different atmospheres such as hydrogen or argon gas and different sintering temperature. Hot-pressed composite in a hydrogen atmosphere exhibited less reaction phase of $FeAl_2O_4$ and enhanced mechanical properties than that in an argon atmosphere. Furthermore, decreasing hot-pressing temperature produced a refinement of ceramic matrix and metallic dispersion particles as well as improvement of mechanical properties. The change of mechanical properties in the composites with different sintering conditions was explained by microstructural characteristics relating to reaction phase formation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.19.2-19.2
• /
• 2010

Printed electronics using printing process has broadened in all respects such as electrics (lighting, batteries, solar cells etc) as well as electronics (OLED, LCD, E-paper, transistor etc). Copper is considered to be a promising alternative to silver for printed electronics, due to very high conductivity at a low price. However, Copper is easily oxidized, and its oxide is non-conductive. This is the highest hurdle for making copper inks, since the heat and humidity that occurs during ink making and printing simply accelerates the oxidation process. A variety of chemical treatments including organic capping agents and metallic coating have been used to slow this oxidation. We have established synthetic conditions of copper nanoparticles (CuNPs) which are resistant to oxidation and average diameter of 20 to 50nm. Specific resistivity should be less than $4\;{\mu}{\Omega}{\cdot}cm$ when sintered at lower temperature than $250^{\circ}C$ to be able to apply to conductive patterns of FPCBs using ink-jet printing. Through this study, the parameters to control average diameter of CuNPs were found to be the introduction of additive agent, the feeding rate of reducing agent, and reaction temperature. The CuNPs with various average diameters (58, 40, 26, 20nm) could be synthesized by controlling these parameters. The dispersed solution of CuNPs with an average size of 20 nm was made with nonpolar solvent containing 3 wt% of binder, and then coated onto glass substrate. After sintering the coated substrates at $250^{\circ}C$ for 30 minutes in nitrogen atmosphere, metallic copper film resulted in a specific resistivity of $4.2\;{\mu}{\Omega}{\cdot}cm$.

• Nuclear Engineering and Technology
• /
• v.49 no.4
• /
• pp.734-743
• /
• 2017

In order to investigate the swelling behavior and fuel-cladding interaction mechanism of U-10Zr alloy metallic fuel at very low burnup, an irradiation experiment was concisely designed and conducted on the China Mianyang Research Reactor. Two types of irradiation samples were designed for studying free swelling without restraint and the fuel-cladding interaction mechanism. A new bonding material, namely, pure aluminum powder, was used to fill the gap between the fuel slug and sample shell for reducing thermal resistance and allowing the expansion of the fuel slug. In this paper, the concise irradiation rig design is introduced, and the neutronic and thermal-hydraulic analyses, which were carried out mainly using MCNP (Monte Carlo N-Particle) and FLUENT codes, are presented. Out-of-pile tests were conducted prior to irradiation to verify the manufacturing quality and hydraulic performance of the rig. Nondestructive postirradiation examinations using cold neutron radiography technology were conducted to check fuel cladding integrity and swelling behavior. The results of the preliminary examinations confirmed the safety and effectiveness of the design.

• Tribology and Lubricants
• /
• v.31 no.2
• /
• pp.69-77
• /
• 2015

Recently, there have been reports of severe symptoms of wear in bearings due to foreign substances mixed in lubricants. Therefore, studying the effects of foreign substances (such as combustion products and metallic debris) on the wear characteristics of journal bearings and proposing appropriate management standards for lubricant cleanliness have become necessary. Studies on the effect of particle size and concentration of foreign substances on surface damage have actively progressed in the recent times. These studies indicate the possibility of foreign substances causing direct wear of bearing surfaces. However, experiments conducted until now involve only basic tests such as the Pin-on-Disk test instead of those involving real bearing systems. This study experimentally examines the damage to the surface of a journal bearing due to foreign substances (combustion products and alumina) mixed with the lubricant, as well as the effect of the type and size of particles on its wear characteristics. The study uses an experimental journal bearing similar to a real bearing system for conducting the lubrication test. Hydrodynamic Lubrication (HL) numerical analysis, experiment results, and film parameters are used for calculating the operating conditions required for achieving the desired film thickness, and the results of the analysis are modified for considering the surface roughness. The run-time of the experiment is 10 min including the stabilization process. The experiment results show that alumina particles larger than the minimum film thickness cause significant surface damage.

• Clean Technology
• /
• v.25 no.2
• /
• pp.107-113
• /
• 2019

Numerical model that considered the shrinking core model and elutriation and degradation of particles was developed to predict selective chlorination of ilmenite and carbo-chlorination of $TiO_2$ in a two stage fluidized bed chlorination furnace. It is possible to analyze the fluidized bed chlorination reaction to be able to reflect particle distribution for mass balances and the chlorination reaction. The numerical model showed an accuracy with error less than 6% compared with fluidized bed experiments. The chlorination degree with particle size change was greater with a smaller particle size, and there was a 100 min difference to obtain a chlorination degree of 1 between $75{\mu}m$ and $275{\mu}m$. This was not shown to such a great extent with variation of temperature ($800{\sim}1000^{\circ}C$), and there was only a 10 min difference to obtain a chlorination degree of 0.9. In the first selective chlorination process, the mass reduction rate approached to the theoretical value of 0.4735 after 180 min, and chlorination changed the Fe component into $FeCl_2$ or $FeCl_3$ and showed nearly 1. In the second carbo-chlorination process, the chlorination degree of $TiO_2$ approached 0.98 and the mass fraction reached 0.02 with conversion into $TiCl_4$. In the first selective chlorination process, 98% of $TiO_2$ was produced at 180 min, and this was changed into 99% of $TiCl_4$ after an additional 90 min. Also the mass reduction rate of $TiO_2$ was reduced to 99% in the second continuous carbo-chlorination process.