• Korean Journal of Food Science and Technology
• /
• v.27 no.4
• /
• pp.564-570
• /
• 1995

N-Benzoyl-L-aspartyl-L-phenylalanine methyl ester(BzAPM), a novel aspartame precursor, was investigated for its enzymatic synthesis by immobilized thermolysin using a water-miscible organic solvent system. The substrate used were N-benzoyl-L-aspartic acid(BzAsp) and L-phenylalanine methyl ester (PheOMe). Synthetic conditions such as substrates concentration, temperature, pH, and some metallic ions were varied to study their effects on BzAPM synthesis. The synthetic reaction rate increased linearly as the PheOMe concentration increased at a constant concentration of BzAsp(100 mM), and the maximum reaction rate was obtained at BzAsp concentration of 200 mM when 300 mM PheOMe was used. The optimum pH and temperature were found to be 6.1 and $40^{\circ}C$, respectively. The metallic ions such as $Zn^{2+},\;Mg^{2+},\;Mn^{2+},\;Fe^{2+},\;Pb^{2+}\;and\;Cu^{2+}$ at 5 mM level showed inhibitory effect on BzAPM synthesis, while $Co^{2+}$ and $Ca^{2+}$ ion increased synthesis. $Co^{2+}$ ion was also found to have synergistic effect with $Ca^{2+}$ ion. Benzoic acid, L-phenylalanin and NaCl showed inhibitory effect.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.1
• /
• pp.97-100
• /
• 2004

Tetragonal $K_2NiF_4$-type $La_{2-2x}Sr_{2x}Cu_{1-x}Fe_xO_{4-y}$ solid-solution have been synthesized by citrate based sol-gel method. The valence state of iron was determined by Mossbauer spectroscopy and subsequent iodometric titration clearly showed that the copper ions in this solid-solution are in the mixed valence state Cu(II/III). When x ${\geq}$ 0.3, Fe(III) is competing with the mixture of Cu(II) and Cu(III) and $La_{2-2x}Sr_{2x}Cu_{1-x}Fe_xO_{4-y}$ exhibits a metallic character. No evidence for Cu(II)-O-Fe(IV) ${\leftrightarrow}$ Cu(III)-O-Fe(III) valence degeneracy was observed. In contrast, a small amount of Fe(IV) is observed with increasing x (x = 0.4 and 0.5), revealing a semiconducting behavior. These results suggest that the electronic interaction of Cu(III)-O-Fe(III) contributes greatly to the metallic character, while the electronic interaction of Cu(II)-O-Fe(IV) deteriorates the metallic character of $La_{2-2x}Sr_{2x}Cu_{1-x}Fe_xO_{4-y}$.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.12-20
• /
• 2022

The smelting reduction of spent lithium-ion batteries results in metallic alloys containing Co, Cu, Fe, Mn, Ni, and Si. A process to separate metal ions from the sulfuric acid leaching solution of these metallic alloys has been reported. In this process, ionic liquids are employed to separate Fe(III) and Cu(II). In this study, D2EHPA and Cyanex 301 were employed to replace these ionic liquids. Fe(III) and Cu(II) from the sulfate solution were sequentially extracted using 0.5 M D2EHPA with three stages of cross-current and 0.3 M Cyanex 301. The stripping of Fe(III) and Cu(II) from the loaded phases was performed using 50% (v/v) and 60% (v/v) aqua regia solutions, respectively. The mass balance results from this process indicated that the recovery and purity percentages of the metals were greater than 99%.

• Journal of Adhesion and Interface
• /
• v.4 no.2
• /
• pp.21-29
• /
• 2003

Hot AC anodising has been evaluated us pre-treatment for aluminium prior to structural adhesive bonding. Phosphoric and sulphuric acid hot AC anodising showed very promising adhesion promoter capabilities with durability comparable with the best standard DC anodising procedures. AC anodising does not required etching prior to anodising and offers u pre-treatment time down to 20 seconds. The interface/interphase between the aluminium substrate and the adhesive was investigated in order to get a better understanding of the involved adhesion mechanisms and to explain the long-tenn properties. The alkaline medium formed at the oxide layer/adhesive interface has been shown to induce a partial dissolution of the oxide layer leading to the formation of metallic ions which diffuse in the adhesive (EPMA measurements). The effect of diffusion of the Al ions on adhesion and joint durability is still uncertain but studies showed that pre-bond moisture affected the joints durability and to some extent the diffusion length. specially for DC anodised samples. So far no direct correlation could be established between the diffusion length d and the joints durability but new trials with better control over the elapsed time between bonding and adhesive curing are expected to help getting a better understanding of the involved mechanisms.

• Journal of the Korean earth science society
• /
• v.24 no.5
• /
• pp.402-410
• /
• 2003

When the bivalve fossil microstructure is observed on a thin section, the growth lines of the older specimens are mostly erased by calcite recrystallization while those of the younger are well preserved in detail. During the fossil diagenesis, the shells tend to darken gradually since the valve-forming component Ca$^{2+}$ is the replaced by the surrounding materials Fe$^{2+}$, Mg$^{2+}$, and Mn$^{2+}$. Therefore, the metallic ratio against Ca component in fossil was increased during diagenesis. The UV-Visible spectrophotometry analysis shows that the reflecting degree is low level in Cretaceous bivalve fossils in contrast to the Tertiary and Recent ones. This result suggests that the dark color in older bivalve fossils is affected by the replacement of the metal ions.

• Journal of Electrochemical Science and Technology
• /
• v.5 no.4
• /
• pp.115-127
• /
• 2014

Cd-Pb thin films were electrodeposited from a diluted chloride solution using stainless steel rotating disc electrode. The linear sweep voltammograms of the single metallic ions show that electrodeposition of these ions was mass transfer control due to the plateau observed for different rotations at concentration (50 and 200 ppm). The voltammograms of binary system elucidate that electrodeposition process always start at cathodic potential located between the potential of individual metals. Currents transients measurements, anodic linear sweep voltammetry (ALSV) and atomic force microscopy (AFM) were used to characterize the electrocryatalization process and morphology of thin films. ALSV profiles show a differentiation for the dissolution process of individual metals and binary system. Two peaks of dissolution Cd-Pb film were observed for the binary system with different metal ion concentration ratios. The model of Scharifker and Hills was used to analyze the current transients and it revealed that Cd-Pb electrocrystalization processes at low concentration is governed by three-dimensional progressive nucleation controlled by diffusion, while at higher concentration starts as a progressive nucleation then switch to instantaneous nucleation process. AFM images reveal that Cd-Pb film electrodeposited at low concentration is more roughness than Cd-Pb film electrodeposited at high concentrated solution.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.4
• /
• pp.553-556
• /
• 2007

We previously reported a 27.12 MHz inductively coupled plasma source at atmospheric pressure for atomic emission spectrometry based on polymer microchip plasma technology. For the PDMS polymer microchip plasma, molecular emission was observed, but no metallic detection was done. In this experiment, a lab-made electrothermal vaporizer (ETV) with tantalum coil was connected to the microchip plasma for aqueous sample introduction to detect metal ions. The electrode geometry of this microchip plasma was redesigned for better stability and easy monitoring of emission. The plasma was operated at an rf power of 30-70 W using argon gas at 300 mL/min. Gas kinetic temperatures between 800-3200 K were obtained by measuring OH emission band. Limits of detection of about 20 ng/mL, 96.1 ng/mL, and 1.01 μ g/mL were obtained for alkali metals, Zn, and Pb, respectively, when 10 μ L samples in 0.1% nitric acid were injected into the ETV.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.47-47
• /
• 2010

Discharge under the water is very hard and demand considerable high voltage. But specially improved electrode can generate plasma discharge to salty water with relatively low voltage. A round shape ceramic electrode having many pinholes combined with metallic one can generate plasma. 400 volt, 10 kHz and 3 micro second pulse width were applied to repeatedly running synthetic seawater with 10 L/m velocity, containing cultivated E. coli and Bacillus. As a result, 18, 94, 99.97, 100, 100 % disinfection rates to E. coli and 17.1, 17.1, 82.9, 99.4, 99.9 % disinfection rates to Bacillus subtilis were achieved to 1, 2, 3, 4, 5 times repetitive treatment respectively. In the plasma condition, the ions and electrons are separated and new kinds of components are re-synthesized by the intensive movement of the components. Especially chlorine ions are separated and recombined to residual free chlorine like HOCl, $OCl^-$. The residual free chlorine concentrations of discharged water were 0.25, 0.88, 1.39, 1.59, 1.66 mg $Cl_2$/L after 5 times treatment respectively. Another unconfirmed radical and oxidants for example, OH, $H_2O_2$, and $O_3$ can have an effect on microorganism of course.

• Bulletin of the Korean Chemical Society
• /
• v.11 no.6
• /
• pp.564-567
• /
• 1990

A lithiated compound $Li_{0.1}Pr^{3+}Ba_2Cu_3O_y$ has been successfully prepared by electrochemical method, which is achieved with a two electrode cell of the type: Metal(Li)/($Li^+\;,\;ClO_4^-$) + propylene carbonate/$PrBa_2Cu_3O_y$. All Pr ions in the lithiated compound are stabilized with a trivalent state as the other rare earths (Ⅲ) substituted in the 90K superconductor lattice ($Y_{1-x}Ln_x^-Ba_2Cu_3O_{7-{\delta}}$). Powder X-ray diffraction analysis shows that both compounds, $PrBa_2Cu_3O_y$ and $Li_{0.1}PrBa_2Cu_3O_y$ are isostructural with the 90 K superconductor, ($YBa_2Cu_3O_{7-{\delta}}$), nevertheless both of them are non-metallic and also non-superconducting down to 10 K. Magnetic susceptibility ${\chi}$ vs. temperature data indicate that Curie contribution from the magnetic ions (Pr and Cu) is weakened on the one hand, but on the other hand temperature-independent part of susceptibility ${\chi}_o$ increases depending upon the rate of lithium intercalation in $PrBa_2Cu_3O_y$ lattice.

• Membrane and Water Treatment
• /
• v.13 no.3
• /
• pp.121-128
• /
• 2022

A tremendous amount of energy resources is being wasted in cleaning wastewater to save the environment across the globe. Several different procedures are commercially available to process wastewater. In this work, membrane filtration technique is used to treat the textile wastewater because of its cost effectiveness and low environmental impacts. Mixed Matrix Membrane (MMM) consist of Polyvinyl Alcohol (PVA) in which Graphene Oxide (GO) was added as a filler material. Five different membranes by varying the quantity of GO were prepared. The prepared membrane has been characterized by Scanning Electron Microscopy (SEM), X-Ray Diffractometry (XRD), Fourier Transformed Infrared Spectroscopy (FTIR) and Water Contact Angle (WCA). The prepared membranes have been utilized to treat textile wastewater. The synthesized membranes are used for the elimination of total dissolve solids (TDS), total suspended solids (TSS), Methylene blue (MB) dye and copper metallic ions from textile wastewater. It is concluded that amount of GO has direct correlation with the quality of wastewater treatment. The maximum removal of TDS, TSS, MB and copper ions are found to be 7.42, 23.73, 50.53 and 64.5% respectively and are achieved by 0.02 wt% PVA-GO membrane.