• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.784-790
• /
• 2003

Present investigation shows the analysis results for ceramic reinforced metal matrix composite under uniaxial transverse tensile loading. The resulting deformation, the projected damage type, and stress-strain behavior were computed depending on microstructure details such as the type of periodic reinforcement array, and the type of interface bonding. A two-dimensional finite element analysis was conducted based on the unit-cell of square, hexagonal, or diagonal periodic away For composite with strong interface bonding, the transverse stress vs. strain curve was generally increased with the increase of the ceramic volume fraction. For the composite with weakly bonded interface, however, the transverse stress vs. strain curve was reduced against the ceramic volume fraction. The decrease was caused by the interface debonding-induced stiffness reduction of the composite. For the composite of weakly bonded interface, the relative reduction rate in the final limit stress for hexagonal array was larger than that for square array. Outcome of the present study was compared favorably with the published literature data.

• Journal of the Korean Ceramic Society
• /
• v.23 no.4
• /
• pp.27-34
• /
• 1986

In the present study an attempt was made to synthesize $10TiO_2$.$90SiO_2$ glass by Sol-Gel process. Tetra-ethyl-ortho-silane and titanium-iso-propoxide were used as precursors. As the mutual solvent ethanol and iso-propanol were used. TEOS was partially hydrolyzed with one-fold mole of $H_2O$ prior to the reaction with titanium-iso-propoxide to control the difference of hydrolysis rate of the two metal alkoxides. At gelling temperature higher than 6$0^{\circ}C$ it was difficult to obtain monolithic gels. At such a low temperature as 85$0^{\circ}C$ clear amorphous gel derived glass with Si-O-Ti bonding was obtained.

• The korean journal of orthodontics
• /
• v.34 no.4 s.105
• /
• pp.325-332
• /
• 2004

A self-etching primer that combines the etchant and primer in one chemical compound saves time and should be mote cost-effective to the clinician and patient. The purpose of this study was to evaluate the clinical effectiveness of a self-etching primer by measuring shear bond strengths according to various conditions and observing adhesive failure patterns. For this Investigation, 120 upper and lower premolars extracted for orthodontic purposes were used and randomly divided into six groups of twenty teeth each. Human premolars were embedded in a metal cylinder with orthodontic resin. Metal brackets and ceramic brackets were bonded with XT primer and self-etching primer by means of XT adhesive. Upon curing, plasma arc light and visible light were used. After bonding, the shear bond strength was tested by Instron universal testing machine, and the amount of residual adhesive that remained on the tooth after debonding was measured by stereoscope and assessed with an adhesive remnant index. The results were as fellows: 1. When brackets were bonded, if other conditions remained the same, there was no significant difference in shear bond strength due to the type of primer - either self-etching primer or XT primer. 2. When metal brackets were bonded, there was no significant difference in shear bond strength according to the source of light - plasma arc light or visible light - and type of primer. 3. There was a very significant difference in shear bond strength according to the type of brackets - metal or ceramic brackets. The shear bond strength of ceramic brackets was stronger than metal brackets. 4. When the adhesive failure patterns of metal brackets bonded with self-etching primer were observed by using the adhesive remnant index, the bond failure of the metal bracket occurred more frequently at the bracket-adhesive. The failure of the ceramic bracket, however, occurred more frequently at the enamel-adhesive interface. The adhesive failure patterns of metal brackets bonded with XT primer observed the same patterns. The above results suggest that self-etching primer can be clinically useful for bonding the brackets without fear of a decrease in shear bond strength.

• Journal of Technologic Dentistry
• /
• v.35 no.2
• /
• pp.89-95
• /
• 2013

Purpose: The purpose of this study was to evaluate bond strength of Metal Disk alloy and casting alloy. Methods: Metal specimens were divided into 4 groups for each alloy. Three point flexural test were used to measure the bond strength of CAD/CAM metal alloy and casting alloy. Statistical analysis was done using the Statistical Package for Social Sciences version 19.0 for Windows. As for the analysis methods, the study used Kruskal-Wallis test. Results: The average bonding strengths of Group 1 to porcelain was $36.7{\pm}9.90$ MPa, Group 2 to porcelain was $37.68{\pm}4.51$ MPa, Group 3 to porcelain was $36.43{\pm}6.57$ MPa, Group 4 to porcelain was $42.88{\pm}6.81$ MPa, Each group was not significantly different. Conclusion: Bond strength of Casting alloy is equal to or higher than bond strength of CAD/CAM Metal Disk alloy. Alloy clinical bond strength is 25 MPa, So CAD/CAM Metal Disk alloy can be used as dental material.

• Resources Recycling
• /
• v.33 no.4
• /
• pp.29-35
• /
• 2024

The recycling of waste resources, such as spent catalysts, primarily involves leaching and extracting metal components via smelting. These metal components are then recovered as salts, such as sulfates and nitrates. When crystallization occurs during the calcination of the recovered salts, the salts are converted into oxides, which are then reduced to form metals or ceramic materials. Common reducing agents used in oxide reduction include hydrogen and carbon, and metal powders are obtained upon reduction. Carbide synthesis can occur if the recycled element is a transition metal and carbon is used as the reducing agent. Despite being ceramic materials, transition metal carbides exhibit excellent conductivity owing to their metallic bonding. Recently, MXene, a two-dimensional transition metal carbide, has gained attention for electromagnetic wave shielding, secondary battery electrodes, and water purification owing to its electrical conductivity and large surface area. This study developed a process for synthesizing high-value MXene materials from waste resources. The properties of these MXenes were evaluated to confirm the potential of using waste resources as raw materials for MXenes.

• Restorative Dentistry and Endodontics
• /
• v.43 no.1
• /
• pp.7.1-7.7
• /
• 2018

Objectives: The aim of this study is to compare the shear bond strengths of ceramic brackets bonded to zirconia surfaces using different zirconia primers and universal adhesive. Materials and Methods: Fifty zirconia blocks ($15{\times}15{\times}10mm$, Zpex, Tosoh Corporation) were polished with 1,000 grit sand paper and air-abraded with $50{\mu}m$ $Al_2O_3$ for 10 seconds (40 psi). They were divided into 5 groups: control (CO), Metal/Zirconia primer (MZ, Ivoclar Vivadent), Z-PRIME Plus (ZP, Bisco), Zirconia Liner (ZL, Sun Medical), and Scotchbond Universal adhesive (SU, 3M ESPE). Transbond XT Primer (used for CO, MZ, ZP, and ZL) and Transbond XT Paste was used for bracket bonding (Gemini clear ceramic brackets, 3M Unitek). After 24 hours at $37^{\circ}C$ storage, specimens underwent 2,000 thermocycles, and then, shear bond strengths were measured (1 mm/min). An adhesive remnant index (ARI) score was calculated. The data were analyzed using one-way analysis of variance and the Bonferroni test (p = 0.05). Results: Surface treatment with primers resulted in increased shear bond strength. The SU group showed the highest shear bond strength followed by the ZP, ZL, MZ, and CO groups, in that order. The median ARI scores were as follows: CO = 0, MZ = 0, ZP = 0, ZL = 0, and SU = 3 (p < 0.05). Conclusions: Within this experiment, zirconia primer can increase the shear bond strength of bracket bonding. The highest shear bond strength is observed in SU group, even when no primer is used.

• Journal of the Korean Ceramic Society
• /
• v.34 no.11
• /
• pp.1151-1158
• /
• 1997

Fracture of uni-directional carbon fiber reinforced carbon matrix composite is strongly dependent on the orientation of basal plane in graphite matrix when it is limited within matrix. The orientation of basal planes are vertically stacked to carbon fiber which results in the weakness for applied tensile or shear force in thermosetting resin derived-carbon matrix composite. Microtextural control of the matrix was tried through chemical interaction between metal carbides and furan resin derived-carbon matrix. SiC and TiO2 addition made the orientation disordered. However, porosity increased due to decomposition of SiC. Interfacial bonding could be controlled by TiO2 addition, but carbon fiber was considerably reacted with TiC during thermal treatment higher than 2$600^{\circ}C$. Therefore, it is desirable to control the thermal treatment temperature at which decomposition of SiC was not serious and TiC/C was not formed eutectoid.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.10 no.2
• /
• pp.15-20
• /
• 2001

The spaced dentition is a common clinical finding. The careful analysis of clinically spaced dentition is a necessity for effective treatment planning. Spaced dentition often exists in the presence of intact teeth. Therefore, special care should be taken in order to obtain the most successful esthetic effect and to prevent overtreatment as well. The aesthetic restorative dental treatment using the porcelain laminate veneers is getting more popular than the complex orthodontic treatment, and prosthetic solutions that require sacrifice of sound tooth structure. The physical strength of porcelain laminate veneers is not as good as porcelain fused metal crowns, and more researches are needed in the field of bonding between composite cement and porcelain laminate veneer. However, the esthetic results from this unprepared porcelain laminate veneers were satisfactory with Authentic (Ceramay, Germany) pressable ceramic technique and resin cement (Rely X Veneer, 3M). This article deals with 2 cases of unprepared porcelain laminate veneers on anterior teeth.

• Journal of the Korean Ceramic Society
• /
• v.36 no.11
• /
• pp.1228-1234
• /
• 1999

In order to form a uniform oxidation layer and spinel crystalline phase that was supposed to help strong bonding in Kovar(Fe-29Ni-17Co)to-glass sealing the humidified nitrogen (2.3%H2O/N2) was used as an oxidation atmosphere. Kovar oxidation was diffusion-contolled and the activation energy was 2.51 kcal/mol at 600-900$^{\circ}C$ After oxidation at 600$^{\circ}C$ the oxidation layer was under 1$\mu\textrm{m}$ thickness and crystalline phase was spinel which was found to be suitable for the Kovar-to-glass sealing.

• Journal of Technologic Dentistry
• /
• v.29 no.2
• /
• pp.119-128
• /
• 2007

Although there are many different ways that restorations can be made, it can be said that the biocompatibility of abutment and crown is very important in this experiment. When placed in the actual oral cavity, the differences were obvious. Compared to In-ceram Aluminium, the structure that is obtained after firing reveals a particularly homogeneous distribution of the crystal and glass phase. The In-ceram aluminium system had many problems, such as having weak tensile strength, and having low bonding strength due to the shrinking that occurs after firing. Because of the opaque finish of the metal frame, the two may look similar from the outside, but it is evident that there are differences between using a metal frame and In-ceram. VITA VM9 has been designed as a special ceramic featuring a fine structure or stabilized Zro2 substructures, and so the VITA VM9 excels in its light refraction and reflection behavior, which is similar to natural teeth. It also has outstanding chemical balance, which presents advantages such as considerably reduced accumulation of plaque on the ceramic surface.? This ultimately results in easier care and cleaning for the patient.