• 소성∙가공
• /
• 제15권8호
• /
• pp.615-620
• /
• 2006

The reduction behavior of $TiO_{2}$ in Al and Al/CaSi containing self-reducing $TiO_{2}$ briquettes(SRTB) was investigated. The maximum yield of Ti was expected with the slag composition of 45-55%CaO in the $CaO-Al_{2}O_{3}$ system. When $CaCO_{3}$ was used as a flux, the oxidation loss of reducing agent by $CO_{2}$ should be compensated, and therefore it leads to excessive requirement of the reducing agent. By using Al and CaSi mixture as a reducing agent of $TiO_{2}$, the reaction products both oxide and metal could be liquefied, and separated effectively with each other. As a result, the yield of Ti increases remarkably. The optimum mixing ratio of CaSi to Al is 78%CaSi-22%Al.

• 동력기계공학회지
• /
• 제12권3호
• /
• pp.60-65
• /
• 2008

This study aims at investigating the wear properties of thermally sprayed $Al/Al_2O_3$ metal matrix composite(MMC) coating against different counterparts. $Al/Al_2O_3$ MMC coatings were fabricated using a flame spray system on an Al 6061 substrate. Dry sliding wear tests were performed using the sliding speeds of 0.2m/s and the applied loads of 1 and 2 N. AISI 52100, $Al_2O_3$, $Si_3N_4\;and\;ZrO_2$ balls(diameter: 8mm) were used as counterpart materials. Wear properties of $Al/Al_2O_3$ MMC coatings were analyzed using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDX). It was revealed that wear properties of $Al/Al_2O_3$ composite coatings were much influenced by counterpart materials. In the case of AISI 52100 used as counterparts, the wear rate of composites coating layer increased according to the increase of the applied load. On the contrary, in the case of ceramics used as counterparts, the wear rate of composites coating layer decreased according to the increase of the applied load.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 추계기술심포지움논문집
• /
• pp.69-72
• /
• 2002

B $i_{3.3}$L $a_{0.7}$ $Ti_3$ $O_{12}$(BLT) 강유전체 박막을 $Al_2$ $O_3$/Si 기판위에 졸-겔(sol-gel)법으로 스핀 코팅하여 Metal-Ferroelectric-Insulator-Silicon (MFIS) 구조를 형성하였다. 박막의 결정화를 위해 as-coated 박막을 산소분위기에서 $650^{\circ}C$ 및 $700^{\circ}C$에서 30분 동안 후속열처리를 실시하였다. BLT 박막의 열처리 온도를 $650^{\circ}C$에서 $700^{\circ}C$로 증가시킴에 따라서 c축으로 우선 배향되는 경향을 보였으며, FWHM 값이 감소하여 결정성이 향상됨을 확인할 수 있었다. $700^{\circ}C$에서 열처리된 BLT 박막의 memory window는 약 2.5V (인가전압 5V)를 나타내었으며, 누설전류는 약 1.5x$10^{-7}$ A/$\textrm{cm}^2$를 나타내었다.다.다.

• 한국세라믹학회지
• /
• 제41권4호
• /
• pp.297-301
• /
• 2004

분무연소합성법을 이용하여 나노크기의 물라이트(3Al$_2$O$_3$$.$2SiO$_2$) 콜로이드를 제조하였다. 연소반응을 위한 산화제로서 Al(NO$_3$)$_3$$.$9$H_2O$와 환원제(연료)로서 CH$_{6}$N$_4$O를 사용하였으며, 실리카 소스로서 콜로이드 실리카를 첨가하였다. 분무된 액적들의 착화를 위해 연소반응기의 온도를 80$0^{\circ}C$로 유지하였다. 액적의 응고에 의한 액적크기 성장을 억제하기 위하여 금속 스크린 필터를 사용함으로써 액적의 개수 농도를 감소시켰으며, 에어로졸 입자의 체류시간을 2.5초로 유지하여 열 유체의 흐름을 층류로 유도하였다. 제조된 입자들의 모양은 모두 구형이었으며, 평균입자크기는 130nm이었다 XRD와 TEM 분석 결과 각각의 초미립자들은 정량화합물의 물라이트 결정성을 나타내었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.59.1-59.1
• /
• 2010

Aluminum-induced crystallization (AIC) of amorphous silicon (a-Si) is studied with the structure of a glass/Al/$SiO_2$/a-Si, in which the $SiO_2$ layer has micron-sized laser holes in the stack. An oxide layer between aluminum and a-Si thin films plays a significant role in the metal-induced crystallization (MIC) process determining the properties such as grain size and preferential orientation. In our case, the crystallization of a-Si is carried out only through the key hole because the $SiO_2$ layer is substantially thick enough to prevent a-Si from contacting aluminum. The crystal growth is successfully realized toward the only vertical direction, resulting a crystalline silicon grain with a size of $3{\sim}4{\mu}m$ under the hole. Lateral growth seems to be not occurred. For the AIC experiment, the glass/Al/$SiO_2$/a-Si stacks were prepared where an Al layer was deposited on glass substrate by DC sputter, $SiO_2$ and a-Si films by PECVD method, respectively. Prior to the a-Si deposition, a $30{\times}30$ micron-sized hole array with a diameter of $1{\sim}2{\mu}m$ was fabricated utilizing the femtosecond laser pulses to induce the AIC process through the key holes and the prepared workpieces were annealed in a thermal chamber for 2 hours. After heat treatment, the surface morphology, grain size, and crystal orientation of the polycrystalline silicon (pc-Si) film were evaluated by scanning electron microscope, transmission electron microscope, and energy dispersive spectrometer. In conclusion, we observed that the vertical crystal growth was occurred in the case of the crystallization of a-Si with aluminum by the MIC process in a small area. The pc-Si grain grew under the key hole up to a size of $3{\sim}4{\mu}m$ with the workpiece.

• 공업화학
• /
• 제4권1호
• /
• pp.144-152
• /
• 1993

${\gamma}-Al_2O_3$, ${\alpha}-Al_2O_3$, $SiO_2$, $TiO_2$등에 고정화된 폴리에틸렌글리콜을 $Fe(CO)_5$에 의한 니트로벤젠의 상온 환원반응에 상이동 촉매로 사용하였다. 고정화된 PEG의 몰수는 담체의 비표면적에 따라 증가하였고 PEG/${\gamma}-Al_2O_3$가 가장 좋은 활성을 나타내었다. PEG의 사슬길이가 길고 NaOH 농도가 높을수록 반응속도가 증가하였다. 적외선분광기를 이용하여 반응기구에 대한 고찰도 함께 실시하였으며 폴리에틸렌글리콜 상이동 촉매는 본 반응의 활성물질로 알려진 $HFe(CO)_4{^{-}}$이온의 생성과 이의 유기상으로의 이동을 촉진시키는 것으로 판단되었다.

• 대한화학회지
• /
• 제30권5호
• /
• pp.415-422
• /
• 1986

${\gamma}-Al_2O_3$와 $SiO_2$에 입혀진 CuO계에서 지지체와 금속과의 상호 작용을 X선 회절법과 승온 환원법으로 연구했다. CuO/${\gamma}-Al_2O_3$계의 CuO X선 회절 피크는 구리의 농도가 약 5.0wt % 이상일 때 관찰될 수 있었으며 CuO/$SiO_2$계에서는 2.5wt%의 구리 함량에서도 볼 수 있었다. CuO/${\gamma}-Al_2O_3$의 수소에 의한 승온 환원 실험에서는 145${\circ}C$, 185${\circ}C$, 210${\circ}C$, 그리고 250${\circ}C$부근에서 네개의 주 피크가 나타났으며 CuO/$SiO_2$의 경우는 425${\circ}C$에서의 작은 피크와 함께 250${\circ}C$에서 큰 피크가 나타났었다. 1000${\circ}C$에서 소성시킨 CuO/${\gamma}-Al_2O_3$의 Cu$Al_2O_4$에 대한 승온 환원 피크들과 145${\circ}C$, 200${\circ}C$ (185${\circ}C$, 210${\circ}C$), 250${\circ}C$ 부근의 피크들을 비교해 보면 그들은 각각 ${\gamma}-Al_2O_3$와 상호작용하는 CuO격자에 있는 $Cu^+$이온, ${\gamma}-Al_2O_3$의 결함 자리들에 존재하는 $Cu^+$이온, 그리고 입자가 큰 CuO층에 있는 $Cu^{2+}$이온에 대응시킬 수 있었다. 이러한 결과들로 부터 CuO/${\gamma}-Al_2O_3$계에서는 지지체와 금속간에 상당한 상호작용이 있으며 이 상호 작용이 CuO/${\gamma}-Al_2O_3$계의 $Cu^{2+}$이온을 안정화 시킴을 알 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1588-1590
• /
• 2004

The composites were fabricated, respectively, using 61vol.% SiC - 39vol.% $TiB_2$ and using 61vol.% SiC 39vol.% WC powders with the liquid forming additives of 12wt% $Al_2O_3+Y_2O_3$ by pressureless annealing at 1800$^{\circ}C$ for 4 hours. Reactions between SiC and transition metal $TiB_2$, WC were not observed in this microstructure. The result of phase analysis of composites by XRD revealed SiC(6H), $TiB_2$ and YAG($Al_5Y_3O_{12}$) crystal phase on the SiC-$TiB_2$, and SiC(2H), WC and YAG($Al_5Y_3O_{12}$) crystal phase on the SiC-WC composites. ${\beta}{\rightarrow}{\alpha}$-SiC phase transformation was ocurred on the SiC-$TiB_2$, but ${\alpha}{\rightarrow}{\beta}$-SiC reverse transformation was not occurred on the SiC-WC composites. The relative density, the flexural strength showed respectively value of 96.2%, 310.19Mpa in SiC-WC composites. The electrical resistivity of the SiC-$TiB_2$ and the SiC-WC composites is all positive temperature cofficient resistance(PTCR) in the temperature ranges from 25$^{\circ}C$ to 500$^{\circ}C$.

• 동굴
• /
• 제76호
• /
• pp.61-66
• /
• 2006

The present report is the investigation of the effects of the HIP treatment on plasma-sprayed ceramic coating of $Al_2O_3$, $Al_2O_3-SiO_2$ on the metal substrate. These effects were characterized by phase identification, Vickers hardness measurement, and tensile test before and after HIPing.

• Journal of Welding and Joining
• /
• 제18권3호
• /
• pp.51-59
• /
• 2000

Sink roll has been used in molten 55%Al-Zn alloy bath of continuous galvanizing line for sinking and stabilizing working steel strip in molten metal bath. In the process, the sink roll body inevitably build up dross compounds and pitting on the sink roll surface during 55%Al-Zn alloy coated strip production, and the life time of the sink roll is shorten by build up dross compounds and pitting. The present study examined the application of thermally sprayed ceramic coatings method on sink roll body for improving erosion resistance at molten 55% Al-Zn pool. In this experiment, the stainless steels such as STS 316L and STS 430F were used as the substrate materials. The CoNiCr and WE-Co powder were selected as bond coating materials. Moreover $Al_2O_3-ZrO_2-SiO_2 and ZrO_2-SiO_2$ powders selected as the top coating materials. Appearances of the specimens before and after dipping to molten 55%Al-Zn pool were compared and analyzed. As a result of this study, STS430F of substrate, WC-Co of bond spray coatings, $ZrO_2-SiO_2$ power of top spray coatings is the best quality in erosion resistance test at molten 55%Al-Zn pool