• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.171-176
• /
• 2003

In this study, stress analysis using Boundary Element Method (BEM) was carried to investigate stress distribution in the brazing joint between a Hardmetal and a HSS. The two models were proposed to analyze the stress singularity in the interfaces of the brazing joint. The material type, thickness of the filler metal and the length of the vertical brazing adhesive are considered in the BEM analysis. As results, the peak point of the stress is founded to be in the lower interface of the brazed joint. It should be noted that the maximum stress of the peak point is being affected by the thickness and length of the brazing joint.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.231-234
• /
• 1998

In this study, the wind-mill type ultrasonic motor was fabricated, and then resonant frequency and vibration velocity characteristics of the stator were measured. Brass metal was pressed with umbrella-type using metal mold, then slot of 4 kind was processed in each of thickness. Among sixteen's stators, resonant frequency on vibration velocity was decreased remarkably in stator of higher resonant point, but resonant frequency on vibration velocity wasn't almost changed at lower resonant point of stator. The thickener thickness of elastic body, vibration velocity was decreased. The more slot of elastic body, vibration velocity was increased Applied voltage was changed from 10$V_{max}$ to 100$V_{max}$. Maximum vibration velocity value was 2.0[m/s].

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.749-751
• /
• 1998

In this study, the wind-mill type ultrasonic motor was fabricated, and then revolution and temperature characteristics of the ultrasonic motor were measured. Brass metal was pressed with umbrella-type using metal mold, then slot of 4 kind was processed in each of thickness. Among sixteen's ultrasonic motors, heat loss on applied voltage was much at stator of the highest resonant point, but heat loss on applied voltage was almost neglected at the lowest resonant point of stator. The thickener thickness of elastic body, revolution speed was decreased. The more slot of elastic body, revolution speed was increased. Applied voltage was changed from $10V_{max}$ to $100V_{max}$. When applied voltage was under $20V_{max}$, ultrasonic motor was not rotated. When applied voltage was over $90V_{max}$, revolution of ultrasonic motor was saturated. Maximum revolution speed was 510[rpm].

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.47-50
• /
• 2006

High-speed machining is a very useful tool and one of the most effective rapid manufacturing processes. This study sought to produce various high-speed machining materials with excellent quality and dimensional accuracy. However, high-speed machining is not suitable for microscale thin-walled structures because the structure stiffness lacks the ability to resist the cutting force. This paper proposes a new method that is able to rapidly produce very thin-walled structures. This method consists of high-speed machining followed by filling. A strong work-holding force results from the solidification of the filling materials. Low-melting point metal alloys are used to minimize the thermal effects during phase changes and to hold the arbitrarily shaped thin-walled structures quickly during the high-speed machining. We demonstrate some applications, such as thin-walled cylinders and hemispherical shells, to verify the usefulness of this method and compare the analyzed dimensional accuracy of typical parts of the structures.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.769-772
• /
• 1997

In this study, By employing two dimensional(2-D) Boundary Element Method(BEM) stress analysis was carried to investigate stress distributions on the brazing joint of a Hardmetal and a HSS. Two model was proposed to analyze stress singularity in brazed interface. The stress results from the BEM were considered influence of the kind of materials , thickness of filled metal and length of vertical brazing adhesive. From those obtained results , the peak point of stress was founded in the lower part of two interface was made by brazing. As the thickness and length changed, the maximum stress tended to change in the peak point.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.96.1-96.1
• /
• 2017

This presentation introduces anodizing science of typical valve metals of Al, Mg and Ti, based on the ionic transport through the andic oxide films in various electrolyte compositions. Depending on the electrolyte composition, metal ions and anions can migrate through the andic oxide film without its dielectric breakdown when point defects are present within the anodic oxide films under high applied electric field. On the other hand, if anodic oxide films are broken by local joule heating due to ionic migration, metal ions and anions can migrate through the broken sites and meet together to form new anodic films, known as plasma electrolytic oxidation (PEO) treatment. In this presentation, basics of conventional anodizing and PEO methods are introduced in detail, based on the ionic migration and movement mechanism through anodic oxide films by point defects and by local dielectric breakdown of anodic oxide films.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.258-259
• /
• 2013

Recently, architectural design has been changing from formal design to freeform design due to the digitalization of construction industry. Especially, the formal design has been accepted as a design trend recently and applied many times as a design concept in the architectural design competitions such as turn-key. However, various deflects such as water leak and cracks have been occurred because the traditional construction methods had been applied without any revision or adaptation of the formal construction method for the freeform building construction. Therefore this research proposes location point control method for freeform metal panel installation which is focused on the application of LH JinJu new office.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.132-138
• /
• 1995

Rene80 superalloy was liquid phase diffusion bonded by using boron(B) as an insert material, where B has high diffusivity and higher melting point as an insert material. Bonding procedure and bonding mechanism of Rene80/B/Rene80 joint were investigated. As results, liquid metal was produced by solid state reaction between base metal and insert material on bonding zone. The liquid metal was produced preferentially at the grain boundary. Except for production of liquid metal, other bonding procedure was nearly same as TLP(Transient Liquid Phase) bonding. Bonding time, however, was reduced compared to prior result of TLP bonding. By bonding S.4ks at l453K, Ren80/B/Rene80 joint was isothermally solidified and homogenized where thickness of insert material was 7.5.mu.m.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.31-37
• /
• 2000

Metal matrix composites(MMCs) are rapidly becoming one of the strongest candidates for structural materials for many high temperature application. Among the high temperature environment, thermal shock is known to cause significant degradation in most MMC system. Therefore, the nondestructive evaluation on thermal shock damage behavior of SiC/A16061 composite has been carried out using ultrasonic surface and SH-waves. For this study, Sic fiber reinforced metal matrix composite specimens fabricated by a squeeze casting technique were thermally cycled in the temperature range 25~$400^{\circ}C$ up to 1000 cycles. Three point bend test was conducted to investigate the effect of thermal shock damage on mechanical properties. The relationship between thermal shock damage behavior and the change of ultrasonic velocity and attenuation were discussed by considering SEM observation of fracture surface.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.3
• /
• pp.165-169
• /
• 2003

To extract alkali metal ions and heavy metal ions, search for crown ether model compounds (4a-b, 5a-b, 6a-b) bearing side arm has led to achieve in 5~6 steps starting from 2,6-dimethylaniline. The determination of structure in their compound derivatives were on the basis of melting point and nuclear magnetic resonance spectroscopy. In the solvent extraction of metal ions from the synthesized derivatives, we observed that silver ion has only high selectivity for synergistic ligation of crown ether.