• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1686-1690
• /
• 2005

Although metal ball can be used as parts of bearing or metal filter, that is used by single product with solder ball or shot ball. Also, according as demand of metal ball of various diameter increase, processing property 솜 extension of coverage are important. Especially an optimal design of cutting roller was investigated for determining appropriate dimensions of components of manufacturing system. In this study, the effects of the diameter and the round radius of cutting roller were calculated and analyzed. We applied data of rigid-plastic FEM Simulation in basis design of equipment to solve these issues, and confirmed processing factor about metal ball manufacturing process that use cutting process of metal wire in this research

• Journal of Welding and Joining
• /
• 제4권3호
• /
• pp.58-71
• /
• 1986

Mechanical and corrosion property of duplex stainless steel weldments made by the GTAW and SMAW process were studied. Fracture toughness, general and local corrosion resistance of GTAW and SMAW weldments were evaluated in terms of Charpy V notch impact test, anodic polarization diagram, pitting corrosion rate, respectively. SMA weld metal showed much lower impact toughness and higher ductile-brittle transition temperature than GTA weld metal. Fractographic and EDX analysis on fracture surface of SMA weld metal demonstrated the existence of (Si, Ti), oxide in large amounts. Potentiodynamic anodic polarization diagram of GMA weld metal showed much lower passive current density than SMA weld metal in 4% $H_2/SO_4$ solution. And pitting corrosion rate test showed the same tendency. Relating the microstructure, chemistry and property, it can be concluded that GTA weld metal gives better toughness due to lower oxygen content, i.e. lower inclusion content, and better corrosion resistance due to higher Pitting Index(PI) than SMA weld metal.

• 한국환경과학회지
• /
• 제6권5호
• /
• pp.451-459
• /
• 1997

This paper alms to describe the indoor-outdoor air quality in school environment through the analyses of heavy metal concentration by inductively Coupled Plasma(ICPI, which were observed at some school environment, such as traffic area, industrial area seme-industrial area, and residence area. The results are as follows : (1) Regardless Indoor and outdoor, the area with the highest concentration of heavy metal is industrial area followed by traffic area, residence area and semi-industrial area in descending order of magnitude. And the heavy metal concentration of indoor is higher than that of outdoor. (2) The main heavy metal components with more high level concentration of Indoor than those of outdoor are Zn, Al, Ca and these heavy metal concentrations are higher in class than In corridor and outdoor.

• 한국응용과학기술학회지
• /
• 제26권4호
• /
• pp.440-450
• /
• 2009

Metal(Zinc) soap and mixed metal(Zn/Ba) soap were synthesized with good structures and characterized by IR and H-NMR. The H-NMR spectrums of the synthesized soaps were in very good accordance with the structures proposed by earlier workers. The mixed metal soaps with various costabilizers(acid or metal content effect), which added in order to investigate the thermal stabilization effect at low and high temperature, were investigated the thermal stabilization effect. The temperature effect is relation to the metal content effect than acid effect. In case of mixed metal soap, the high thermal stabilization effect improved with increasing Barium content. As the Zinc content increase the low temperature thermal stabilization effect improved, but the high temperature thermal stabilization effect showed an opposite tendency.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.36-39
• /
• 2003

Due to the strength and biocompatibility requirement, the stainless steel SUS 316L is widely used for trauma internal fixation device. SUS 316L can be hardened and strengthened only by cold work. In this work, the material compression test is performed both in laboratory and computer simulation by a FEM analysis software DEFORM to correlate the hardness to strain. This data is then used for preform design and predict the hardness of the finish bone plate forging. Finally, we compared the hardness between the actual forging and computer analysis results. Although the predicted hardness from computer simulation. is 55HV higher than the final forging sample, we can get good compatibility on the hardening tendency of cold forging.

• 대한치과교정학회지
• /
• 제19권2호
• /
• pp.85-93
• /
• 1989

The purpose of this study was to evalute the corrosion resistance of chemically and thermally recycled metal brackets. In vivo, two types of recycled metal brackets and new brackets were directly bonded for 1 year, and then the microstructure of bracket surface was examined by S.E.M. (J.S.M.-840 Scanning Electron Microscope, Japan). The following results were obtained. 1) The microstructure of new and chemically recycled metal bracket surfaces showed regular structure without island formation and recrystallization; and after 1 year, the same appearance except some scratches. 2) The microstructure of thermally recycled metal bracket surfaces showed a beginning of island formation and recrystallization by annealing, and after 1 year, a typical corrosive appearance, completely island formation with some metal grains by recrystallization. 3) Chemically recycled metal brackets showed better corrosion resistance than thermally recycled metal brackets.

• Fibers and Polymers
• /
• 제2권1호
• /
• pp.135-139
• /
• 2001

Poly(hydroxamic acid) resin beads were prepared and complexed with various metal ions. We used IR spectroscopy to investigate the structure of metal complex. It proved that the products formed by introduction of metal ions gave stable and colored complex. It was found that the resin bead as synthesized would be a good column packing material for continuous extraction. Energy dispersive spectroscopy was use to study the distribution of metal ions in the resin matrix. It could be tentatively concluded that adsorption and diffusion of metal ions in the chelating resins mainly depended on the loading of the resin matrix which indicated interacting sites with metal ions.

• 한국주조공학회지
• /
• 제8권4호
• /
• pp.429-436
• /
• 1988

The influences of some casting conditions on bonding ratio and state at bonding zone of stainless steel-cast iron dual tube produced by centrifugal casting process were investigated to estimate fabrication technics. 1) Bonding ratio is increasing such as increasing of inner surface temperature of outer metal(stainless steel STS 304), if pouring temperature of inner metal (cast iron) is constant. 2) The more pouring temperature of inner metal (cast iron) increase, the more bonding ratio increase when inner surface temperature of outer metal (cast iron) is constant. 3) As the mold rotary speed is increase, the hatching area of bonding map (perfect bonding area) goes down to the low pouring temperature of inner metal. 4) In order to predict bonding state of two different metal, we are able to make and use the bonding map about casting conditions such as inner surface temperature of outer metal, pouring temperature of inner metal and mold rotary speed.

• 한국CDE학회논문집
• /
• 제8권3호
• /
• pp.150-156
• /
• 2003

Direct Metal Deposition (DMD) is a new additive process producing three-dimensional metal components or tools directly from CAD data, which aims to take mold making and metalworking in an entirely new direction. It is the blending of five common technologies: lasers, CAD, CAM, sensors and materials. In the resulting process, alternatively called laser cladding, an industrial laser is used to locally heat a spot on a tool-steel work piece or platform, forming a molten pool of metal. A small stream of powdered tool-steel metal is then injected into the metal pool to increase the size of the molten pool. By moving the laser beam back and forth, under CNC control, and tracing out a pattern determined by a computerized CAD design, the solid metal part is eventually built line-by-line, one layer at a time. DMD produces improved material properties in less time and at a lower cost than is possible with traditional fabrication technologies.

• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.478-482
• /
• 2016

Metal-supported SOFCs have been investigated to overcome the disadvantages of ceramic-supported SOFCs, including issues related to mechanical strength and sealing. In the case of ceramic-supported cells, the mechanical support is a brittle ceramic or cermet, and it contains expensive materials. However, metal-supported cells utilize ceramic layers that are only as thick as necessary for electrochemical functioning, thereby compensating for the disadvantages of ceramic-supported cells. The mechanical support is fabricated from inexpensive and robust metals, and the electrochemically active layers are applied directly to the metal support. The metal-supported SOFCs thus can provide a reduced system cost, ease of manufacturing, and operational advantages. Owing to these features, metal-supported SOFCs are a very promising candidate for commercialization. Given the importance of studying worldwide trends in metal-supported SOFC research for performance evaluation, this paper reviews development trends with a focus on fabrication methods. Furthermore, a novel fabrication method developed in KAIST is discussed.