• 한국분말재료학회지
• /
• 제24권2호
• /
• pp.133-140
• /
• 2017

This study investigates the oxidation properties of Fe-14Cr ferritic oxide-dispersion-strengthened (ODS) steel at various high temperatures (900, 1000, and $1100^{\circ}C$ for 24 h). The initial microstructure shows that no clear structural change occurs even under high-temperature heat treatment, and the average measured grain size is 0.4 and $1.1{\mu}m$ for the as-fabricated and heat-treated specimens, respectively. Y-Ti-O nanoclusters 10-50 nm in size are observed. High-temperature oxidation results show that the weight increases by 0.27 and $0.29mg/cm^2$ for the as-fabricated and heat-treated ($900^{\circ}C$) specimens, and by 0.47 and $0.50mg/cm^2$ for the as-fabricated and heat-treated ($1000^{\circ}C$) specimens, respectively. Further, after 24 h oxidation tests, the weight increases by 56.50 and $100.60mg/cm^2$ for the as-fabricated and heat-treated ($1100^{\circ}C$) specimens, respectively; the latter increase is approximately 100 times higher than that at $1000^{\circ}C$. Observation of the surface after the oxidation test shows that $Cr_2O_3$ is the main oxide on a specimen tested at $1000^{\circ}C$, whereas $Fe_2O_3$ and $Fe_3O_4$ phases also form on a specimen tested at $1100^{\circ}C$, where the weight increases rapidly. The high-temperature oxidation behavior of Fe-14Cr ODS steel is confirmed to be dominated by changes in the $Cr_2O_3$ layer and generation of Fe-based oxides through evaporation.

• 자원환경지질
• /
• 제40권4호
• /
• pp.347-360
• /
• 2007

고성군에 위치한 폐구리광산의 중금속 오염범위와 정도 및 환경위해성을 평가하기 위하여 광산지역으로부터 토양과 벼를 채취하여 중금속 함량을 분석하였다. 중금속 함량은 논토양에 비해 산토양에서 훨씬 높았다. 중금속 전함량은 산토양에서 Cu>Zn>Pb>As>Cr>Cd, 논토양에서 Zn>Pb>Cu>Cr>As>Cd 순으로 감소하였으며, 0.1/1N HCl에 의한 중금속 용출량은 산토양에서 Cu>Pb>Zn>As>Cd>Cr, 논토양에서 Pb>Cu>Zn>As>Cd>Cr 순으로 나타났다. 중금속 용출비는 시료채취지점에 따라 매우 다양하였지만 평균적으로는 Cd(16%)>Pb(10%)>Cu(9%)>As(4.5%)>Zn-Cr(${\le}2.5%$)의 순이었다. 조사대상 토양들은 지각평균값에 비해 중금속이 부화되어 있으며 그 순서는 $As{\ge}Cd>Pb>Zn>Cu>Cr$이었다. 토양의 중금속 전함량 또는 용출량으로부터 계산한 오염지수는 중금속 오염이 폐구리광산 특히 삼산제일광산 주변의 산토양에 국한되어 있음을 나타내었다. 현미 중의 중금속함량은 As $nd{\sim}0.87mg/kg,\;Cd\;0.02{\sim}0.34mg/kg,\;Cu\;1.01{\sim}6.25mg/kg,\;Mn\;13.4{\sim}43.2mg/kg,\;Pb\;0.09{\sim}2.83mg/kg$ 및 $Zn\;16.5{\sim}79.1mg/kg$으로 심각하게 오염된 수준은 아니었다. 토양 pH와 함께 중금속의 용출 및 분포특성들은 이 지역 중금속 오염의 대부분이 중금속의 용해 순환보다는 폐광석과 맥석광물의 쇄설성 이동에 의해 진행되고 있음을 시사하였다.

• Bulletin of the Korean Chemical Society
• /
• 제33권10호
• /
• pp.3213-3217
• /
• 2012

Reactive adsorption desulfurization (RADS) experiments were conducted over a series of commercial metal oxide supports ($Al_2O_{3-}$, $SiO_{2-}$, $TiO_{2-}$ and $ZrO_{2-}$) supported Ni/ZnO adsorbents. The adsorbents were characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), and Fourier transform infrared spectroscopy (FTIR) in order to find out the influence of specific types of surface chemistry and structural characteristics on the sulfur adsorptive capacity. The desulfurization performance of all the studied adsorbents decreased in the following order: Ni/ZnO-$TiO_2$ > Ni/ZnO-$ZrO_2$ > Ni/ZnO-$SiO_2$ > Ni/ZnO-$Al_2O_3$. Ni/ZnO-$TiO_2$ shows the best performance and the three hour sulfur capacity can achieve 12.34 mg S/g adsorbent with a WHSV of $4h^{-1}$. Various characterization techniques suggest that weak interaction between active component and support component, high dispersion of NiO and ZnO, high reducibility and large total Lewis acidity of the adsorbents are important factors in achieving better RADS performance.

• 한국해양공학회지
• /
• 제22권5호
• /
• pp.87-93
• /
• 2008

The objective of this paper is the investigation of the statistical properties of Vickers hardness (HV) of friction welded parts in nickel based super resisting steel, alloy 718 steel. First, we examine the statistical properties on the case of as-welded parts. Several Virkers indentations were made under same nominal conditions. This was repeated for three different applied loads, 100, 200 and 300g with a duration time, 10 second. The arithmetic mean of Vickers hardness in base metal (BM) materials is larger than that of HAZ in all applied loads. The measure of dispersion, that is, the coefficient of variation (COV) for BM and HAZ is decreased by increasing with the applied load. The distribution of Vickers hardness was not found to be symmetric type. The probability distribution of Vickers hardness was well followed Weibull distribution. The shape parameter and the scale parameter (characteristic hardness) are increased by increasing with the applied load, as both BM and HAZ.

• 한국재료학회지
• /
• 제17권1호
• /
• pp.11-17
• /
• 2007

Turbulent in-situ mixing process is a new material process technology to get dispersed phase in nanometer size by controlling reaction of liquid/solid, liquid/gas, flow ana solidification speed simultaneously. In this study, mixing which is the key technology to this synthesis method was studied by computational fluid dynamics. For the simulation of mixing of liquid metal, static mixers investigated. Two inlets for different liquid metal meet ana merge like 'Y' shape tube having various shapes and radios of curve. The performance of mixer was evaluated with quantitative analysis with coefficient of variance of mass fraction. Also, detailed plots of intersection were presented to understand effect of mixer shape on mixing. The simulations show that the Reynolds number (Re) is the important factor to mixing and dispersion of $TiB_2$ particles. Mixer was designed according to the simulation, and $Cu-TiB_2$ nano composites were evaluated. $TiB_2$ nano particles were uniformly dispersed when Re was 1000, and cluster formation and reduction in volume fraction of $TiB_2$ were found at higher Re.

• 한국군사과학기술학회지
• /
• 제18권5호
• /
• pp.574-581
• /
• 2015

In this paper, the effect of high voltage current pulse against shaped charge jet was analyzed through the visualization of jet behavior using flash X-ray and comparison of depth of penetration(DOP) into RHA(Rolled Homogeneous Armor) witness plates. The behavior of jet particles has been acquired using a flash X-ray equipment when current pulse was applied into the metal jet of a shaped charge(SC) warhead. Typical results such as jet breakup and radial jet dispersion, which are due to electromagnetic pressure by current pulse, have been obtained. Dozens of penetration experiments using a shaped charge with 55 mm diameter were performed according to various combinations of major parametric variables such as electrode spacing, standoff distance from SC warhead to electrode, and charge voltage. Subsequently, interrelations between major parametric variables and DOPs into RHA were analyzed.

• 한국광학회지
• /
• 제21권4호
• /
• pp.175-178
• /
• 2010

본 논문에서는 은-산화막-은 구조의 박막형 에탈론 기반의 투과형 컬러필터를 제안하고 구현하였다. 제안된 박막형 소자는 전자빔 리소그래피 방식에 비해 넓은 유효면적을 갖고 적외선 대역에서의 차단 특성이 우수하다. 또한 금속의 분산특성 및 두께 그리고 기판의 영향 등을 고려하기 위하여 FDTD 방법을 도입함으로써 제안된 소자를 설계 및 분석하였다. 설계된 청색, 녹색, 적색 필터 소자의 산화막 캐비티 두께는 각각 100, 130, 160 nm였으며, 은 박막의 두께는 25 nm였다. 얻어진 측정결과를 살펴보면, 중심파장은 각각 480, 555, 650 nm, 대역폭은 각각 약 120, 100, 120 nm였으며 투과율은 약 60%였다. 그리고 빔의 입사각에 대한 상대적인 투과율 변화율은 ~1%/degree 였다.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3474-3490
• /
• 1996

A metal matrix composites(MMCs) for A16061 reinforced with silicon carbide particles is fabricated by melt-stirring method. The primary products of MMCs billets are prepared by volume fractions 5 vol% to 20 vol% and particle size $13\mu m$ to $22\mu m$.This paper will be made to examine the microstructure and mechanical properties of fabricated $SiC_p$/Al 6061 composite by melt-stirring and squeeze casting method. The MMC billets is extruded at $500^{\circ}C$ under the constant extrusion velocity $V_e$=2mm/min using curved shape die. Extrusion force, particle rearrangement, micro structure and mechanical properties of extruded composites will be investigated. The mechanical properties of primary billets manufactured by melt-stirring and squeeze casting method will be compared with extrusion specimen. The effect of volume fraction and size of the reinforcements will be studied. The increase in uniformity of particle dispersion is the major reason for an improvement in reliability due to hot extrusion with optimal shape die. Experimental Young's modulus and 0.2% offset yield strength for the extruded MMCs will be compared with theretical values calculated by the Eshelby method. A method will be proposed for the prediction of Young's modulus and yield strength in $SiC_p$ reinforced MMCs.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1996년도 추계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.6-6
• /
• 1996

Ceramic based nanocomposite, in which nano-sized ceramics and metals were dispersed within matrix grains and/or at grain boundaries, were successfully fabricated in the ceramic/cerarnic and ceramic/metal composite systems such as $Al_2O_3$/SiC, $Al_2O_3$/$Si_3N_4$, MgO/SiC, mullite/SiC, $Si_3N_4/SiC, $Si_3N_4$/B, $Al_2O_3$/W, $Al_2O_3$/Mo, $Al_2O_3$/Ni and $ZrO_2$/Mo systems. In these systems, the ceramiclceramic composites were fabricated from homogeneously mixed powders, powders with thin coatings of the second phases and amorphous precursor composite powders by usual powder metallurgical methods. The ceramiclmetal nanocomposites were prepared by combination of H2 reduction of metal oxides in the early stage of sinterings and usual powder metallurgical processes. The transmission electron microscopic observation for the $Al_2O_3$/SiC nanocomposite indicated that the second phases less than 70nm were mainly located within matrix grains and the larger particles were dispersed at the grain boundaries. The similar observation was also identified for other cerarnic/ceramic and ceramiclmetal nanocornposites. The striking findings in these nanocomposites were that mechanical properties were significantly improved by the nano-sized dispersion from 5 to 10 vol% even at high temperatures. For example, the improvement in hcture strength by 2 to 5 times and in creep resistance by 2 to 4 orders was observed not only for the ceramidceramic nanocomposites but also for the ceramiclmetal nanocomposites with only 5~01%se cond phase. The newly developed silicon nitride/boron nitride nanocomposites, in which nano-sized hexagonal BN particulates with low Young's modulus and fracture strength were dispersed mainly within matrix grains, gave also the strong improvement in fracture strength and thermal shock fracture resistance. In presentation, the process-rnicro/nanostructure-properties relationship will be presented in detail. The special emphasis will be placed on the understanding of the roles of nano-sized dispersions on mechanical properties.

• 폴리머
• /
• 제25권4호
• /
• pp.503-511
• /
• 2001

기존 실리카 분산제는 주로 Zn, K의 지방산 유도체이며 지방산과 금속비누의 혼합물은 활성을 높이는데 사용되었다. Zn-K 비누 형태의 실리카 분산제는 탄화수소 사슬의 유동성을 증가시켜 실리카가 함유된 고무 배합물의 점도를 낮추어 주며 그 결과 가공성이 향상된다. 실리카 분산제는 가류 특성에 영향을 미쳐서는 안되는데 Zn-K 비누형태의 분산제는 스코치 및 가류시간을 단축시켰다. 그러나 새로이 개발된 분산제의 경우 금속을 함유하지 않은 non-metal 형태이며 분산제가 실리카와 고무간의 interaction을 유도하여 실리카 분산도를 크게 향상시켰으며 이로 인해 경도 및 점도 저하를 유도하였다. 또한 새로운 분산제는 실리카 고무배합물의 가교특성 및 스코치 안정성에 영향을 미치지 않았다.