• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.31-37
• /
• 2000

Metal matrix composites(MMCs) are rapidly becoming one of the strongest candidates for structural materials for many high temperature application. Among the high temperature environment, thermal shock is known to cause significant degradation in most MMC system. Therefore, the nondestructive evaluation on thermal shock damage behavior of SiC/A16061 composite has been carried out using ultrasonic surface and SH-waves. For this study, Sic fiber reinforced metal matrix composite specimens fabricated by a squeeze casting technique were thermally cycled in the temperature range 25~$400^{\circ}C$ up to 1000 cycles. Three point bend test was conducted to investigate the effect of thermal shock damage on mechanical properties. The relationship between thermal shock damage behavior and the change of ultrasonic velocity and attenuation were discussed by considering SEM observation of fracture surface.

• 한국환경과학회지
• /
• 제8권2호
• /
• pp.205-209
• /
• 1999

Iron hydroxides are good adsorbents for uncomplexed metals, some metal-ligand complexes and many metal oxyanions. However, their adsorption properties of these precipitations are not fully exploited in wastewater treatment operations because of difficulties associated with their separation from the aqueous phase. This study describes experiments in which iron hydroxides were coated onto the surface of ordinary adsorbents(Sea sand) that are very resistant to acids, The coated adsorbents were used in adsorption of oxyanionic metals. The process was successful in removing some anions such as $SeO_3(-II)$ over a wide range of metal concentrations and sorption of oxyanionic metals increased with decreasing pH. Formation of two surface complexes for oxyanionic metals adsorption on iron hydroxides comprise (1) complexation of the free anion by a positively charged surface site, and (2) protonation of the adsorbed anion (or alternatively adsorption of a protonated form from solution) The coated adsorbents are inexpensive to prepare and could serve as the basis of a useful oxyanionic metal removal.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.285-291
• /
• 2003

The nanosized silver and gold particles are prepared by ERC method in which metal vapors with high temperature is rapidly quenched by coolants such as liquid nitrogen or liquid argon. In order to monitor the crystal structural changes on the internal and the surface of the nanosized noble metal particles, lattice parameter, internal strain and Debye-Waller factor are investigated, and the calculation of X-ray diffraction scattering intensity is performed. The lattice parameters of silver and gold particles agree with those of bulk materials, and crystal internal strain of the metal particles is not changed by rapid cooling. The Debye-Waller factor of gold particles is increased with decreasing particle size because of the surface softening phenomenon of nanosized particles, but the crystal structural change on the surface of the particles is not detected from the comparison the calculated X-ray diffraction profile with the experimental profile on gold particles with the particle size of 4 nm.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권11호
• /
• pp.585-590
• /
• 2002

In this paper, the 3 dimensional surface charge method is applied to calculate electric fields distribution inside a general and an optimal model of GIS with a metal impurity and a void respectively. We know the optimal model can reduce tangential electric fields at solid insulator surface to 70% of the general model and infulence fields distribution near a metal impurity. Meanwhile, we find the optimal model does not decrease field distribution inside a void in the insulator.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.54-57
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction tests of various sheets were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extreme1y low or high, the friction coefficient is high. As punch comer radius and punch speed are bigger, the value of friction coefficient is smaller. The sensitivity of friction coefficient is mainly governed by lubricant viscosity and sheet surface roughness.

• 대한전자공학회논문지
• /
• 제27권4호
• /
• pp.555-562
• /
• 1990

Alloyed ohmic contact properties of Au-Zn/Au, Au-Be/Au,Au-Zn/Cr/Au, and Au-Be/Cr/Au metal system to p-InP were investigated. Optimum alloying conditions were obtained at the annealing temperature of 425\ulcorner for all the metal systems using a rapid thermal annealing system. Surface AES analysis and auger depth profiling were done for each metal system annealed at the optimum conditions. Outdiffusions of In and P from the InP substrate were found in the metal systems without Cr intermediate layer. Also, small amount of In. P and Cr were detected at the surface in the case of Au-Zn/Cr/Au system, while there were occured no outdiffusion of In, P, and Cr for Au-Be/Cr/Au system. The best surface morpholoty and specific contact resistivity of 4.5x 10**-5 \ulcornercm\ulcornerhave been obtained in this Au-Be/Cr/Au material system alloyed at 425\ulcorner for 60 second.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.87-91
• /
• 2000

Metal ion complex of poly(N-(2,4-imidazoly)ethyl)maleimide-alt-l-octadecene (IMO-O) polymer used to confirm the possibility of molecular device made by Langmuir-Blodgett(LB) method. Electrical properties of the metal ion complex LB film were investigated using Metal/Insulator/Metal(MIM) structure. In the surface pressure-area($\pi$-A) isotherm of IMI-O polymer, the surface pressure at collapse point has a difference due to the interaction between polymer and metal ions. And the complex between polymer and metal ions could be verified through the investigation by Raman spectroscopy. In the current-voltage(I-V) property, the conductivity change of IMO-O polymer complexes due to the kinds of metal of metal ions couldn't be observed. However, the limiting area of molecules was changed by the concentration of the metal ions and the conductivity was increased with the occupied molecular area.

• Nuclear Engineering and Technology
• /
• 제32권1호
• /
• pp.34-45
• /
• 2000

This study is concerned with the experimental test and numerical analysis of the heat transfer and solidification of the molten metal pool with overlying coolant with boiling. In the test, the metal pool is heated from the bottom surface and coolant is injected onto the molten metal pool. Experiments were performed by changing the test section bottom surface temperature of the metal layer and the coolant injection rate. The two-phase boiling coolant experimental results are compared against the dry test data without coolant or solidification of the molten metal pool, and against the crust formation experiment with subcooled coolant. Also, a numerical analysis is performed to check on the measured data. The numerical program is developed using the enthalpy method, the finite volume method and the SIMPLER algorithm. The experimental results of the heat transfer show general agreement with the calculated values. The present empirical test and numerical results of the heat transfer on the molten metal pool are apparently higher than those without coolant boiling. This is probably because this experiment was performed in concurrence of solidification in the molten metal pool and the rapid boiling of the coolant. The other experiments were performed without coolant boiling and the correlation was developed for the pure molten metal without phase change.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권1호
• /
• pp.183-189
• /
• 2018

본 연구에서는 용사기법에 의해 콘크리트 표면에 금속피막을 형성하는 새로운 마감 의장기법의 가능성을 검토하기 위하여, 콘크리트의 함수율 변화에 따른 금속피막의 부착성능에 대하여 실험적인 연구를 수행하였다. 그 결과, 선재의 색은 용사 후에도 변하지 않는 것을 알 있었고, 콘크리트 부착강도 기준인 2.5 MPa를 확보하기 위한 하지 콘크리트의 함수율을 10% 이하로 관리하면 금속피막의 부착강도눈 확보되는 것으로 판단된다. 또한, 콘크리트와 금속피막의 부착강도를 증진시키기 위해서는 표면강화제에 의한 콘크리트 표면강화와 함께 금속피막을 봉공처리제로 봉공하는 것이 매우 유효한 것을 알 수 있었다.

• 한국광학회지
• /
• 제19권1호
• /
• pp.73-79
• /
• 2008

금속선 도파로 면과 금속 평면이 수직으로 적층된 장거리 표면-플라즈몬 도파로 구조를 제안하였으며, 표면-플라즈몬 모드의 특성을 유전체의 굴절율과 두께 변화에 대하여 이론적으로 분석하고 실험적으로 검증하였다. 위층의 금속선 도파로를 S-곡선과 Y-분기 형태로 변형시킨 이중-금속 도파로를 제작하여, 제안된 이중-금속 도파로 구조의 광 소자 응용 가능성을 살펴보았다. 제안된 이중금속 구조에서는 도파로 코어에 해당하는 두 금속 박막 사이의 유전체 굴절률을 임의로 선택하여도 장거리 표면 플라즈몬 모드가 존재할 수 있으며, 표면-플라즈몬 모드의 전파거리는 두 금속 박막 사이의 유전체 두께를 조절함으로써 증가시킬 수 있다. 또한, 이중-금속 도파로는 표면-플라즈몬을 전달할 뿐만 아니라, 삽입된 코어 유전체에 전압 및 전류를 인가하기에도 매우 적합한 구조로서, 표면-플라즈몬 능동소자 및 비선형 소자 구현에 많은 가능성을 열어줄 것으로 기대된다.