• Carbon letters
• /
• 제4권1호
• /
• pp.21-23
• /
• 2003

In this work, the effect of anodic oxidation treatment on Cr(VI) ion adsorption behaviors of activated carbon fibers (ACFs) was investigated. The aqueous solutions of 10 wt% $H_3PO_4$ and $NH_4OH$ were used for acidic and basic electrolytes, respectively. Surface characteristics and textural properties of ACFs were determined by XPS and $N_2$ adsorption at 77 K. The heavy metal adsorption of ACFs was conducted by ICP. As a result, the adsorption amount of the anodized ACFs was improved in order of B-ACFs > A-ACFs > pristine-ACFs. In case of the anodized treated ACFs, the specific surface area was decreased due to the pore blocking or pore destroying by acidic electrolyte. However, the anodic oxidation led to an increase of the Cr(VI) adsorption, which can be attributed to an increase of oxygen-containing functional groups, such as, carboxylic, lactonic, and phenolic groups. It was clearly found that the Cr(VI) adsorption was largely influenced by the surface functional groups, in spite of the reduced specific surface area of the ACFs.

• 대한설비공학회지:설비저널
• /
• 제15권2호
• /
• pp.188-195
• /
• 1986

Condensation heat transfer can be classified in dropwise condensation and filmwise condensation, and for the industrial purpose, the former is more useful than the latter because of the higher heat transfer rate. But it is difficult to maintain the dropwise condensation continuously since most of the metal surfaces become wetted after exposure to a condensing vapor over an extended period of time. To maintain dropwise condensation continuously , various surface coatings and promoters have been used recently, but these methods must be reconsidered about the durability of condensing surface. Therefore, in this study, evaporating method of various pure metals on the condensing surface has been performed to maintain dropwise condensation. The results have showed that the heat transfer rate of silver evaporating surface is higher than any other metal evaporating in dropwise area. Transition temperature and filmwise condensation curves are uniform regardless of kinds of evaporating metals.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.113-120
• /
• 2013

Purpose: This study was to observe surface property and bonding strength according to composition of Ni-Cr alloy for porcelain fused to metal crown. The two kinds of Ni-Cr alloy with different composition ratio of parent metal were observed general properties and chemical properties of each alloy surface and measured the shear bonding strength between ceramic and each alloys. The aim of study was to suggest the material for design of parent metal's composition ratio to development of alloy for porcelain fused to metal crown. Methods: The two kinds of alloy as test specimen was Ni(71wt.%)-Cr(12wt.%) and Ni(63wt.%)-Cr(23wt.%) alloy. The oxide on surface was observed by SEM and EDX. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{71}Cr_{12}$ alloy measured 12.74wt.%, but $Ni_{63}Cr_{23}$ alloy was measured 15.91wt.%. And the maximum shear bonding strength was measured 106.14MPa between $Ni_{71}Cr_{12}$ alloy and vintage halo (VV group). Conclusion: The surface property and oxide characteristic of $Ni_{71}Cr_{12}$ alloy was similar to $Ni_{63}Cr_{23}$ alloy. And VV group has the strongest shear bonding strength.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2023년도 추계학술대회
• /
• pp.135-136
• /
• 2023

본 연구는 금속체 표면파 통신을 이용한 선내 통신 네트워크 구축을 위한 실증 결과이며, 이에 대한 선내 적용방안에 대한 고찰이다. 지난 3년간 5척의 선박을 대상으로 금속체 표면파 통신에 대한 적용 가능성을 확인하였으며, 소형 선박부터 중형선박까지 선내 밀폐 구역에 대한 표면파 통신의 실증을 통해 그 성능을 입증하였다. 통신방식은 IEEE 802.11 기반의 Wi-Fi 통신을 이용하여 무선신호를 표면파롤 전송하는 방식으로 진행하였으며, AP 기반의 데이터를 전송하고 AP - AP의 Point to Point 방식으로 전송속도를 측정하였으며, 표면파 통신이 도달되지 않은 구간은 중계기 AP를 추가하여 전송거리를 연장하는 방안으로 이용하였다. 총 5척의 선박을 통해 무선통신이 불가능한 구역에서 5~100Mbps의 전송속도를 도출함에 따라 선내 Back Bone network를 표면파 기반으로 이용하여 선내 중량 감소, 통신 케이블 구축에 따른 비용 절감이 가능할 것으로 사료된다.

• 한국표면공학회지
• /
• 제45권3호
• /
• pp.136-141
• /
• 2012

'Jikjisimcheyocheal (Jikji afterwards)' is known as a first book printed by the metal type in the world. The metal type used for printing this book has not been found yet. To help for replicating the original metal type, it is required to investigate the composition analysis of the copied metal type. In this study, the composition analysis and thermodynamic care for replicating of ancient metal type was performed on the basis of an analytical reports concerned with the ancient metal type which made after Jikji printing. Metal types were made by remelting and casting of the mother alloy which came from a cast of a mixed metals in accordance with the composition revealed in the literatures. Change of composition during remelting of mother alloy and casting of metal was detected by the EDS analysis. The reasons for variation in composition were discussed by metallurgical and thermodynamic point of view, and a mixing ratio of metals to get the original composition of ancient metal type is suggested. Some attention should be paid on mixing, melting and casting of metals to get an objected composition for copy of ancient metal type.

• 공업화학
• /
• 제10권1호
• /
• pp.67-72
• /
• 1999

Nylon-inorganic filler alloy의 도금에 있어 최적 전처리 공정에 관하여 연구하였다. Nylon-inorganic filler alloy는 etching 공정만으로도 무정형층을 제거하여 요구되는 충분한 밀착력을 얻을 수 있었다. SEM과 표면조도 측정으로부터 etching 공정이 수지표면을 매우 거칠고 접착력을 우수하게 만든다는 결과를 얻었으며, 도금물질의 표면상태와 접착력은 Nylon-inorganic filler alloy 수지의 성형조건에 의존한다는 것을 확인하였다. EDS 분석으로 전처리 후 수지표면의 잔류금속의 종류와 양을 측정한 결과 Cr은 Sn과 Pd의 흡착에 크게 영향을 미치지 않는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제13권1호
• /
• pp.42-52
• /
• 1997

This paper deals with wear characteristics of ion-nitrided metal theoretically and experimentally in order to analysis of wear phenomena. Wear tests show that compound layer of ion-nitrided metal reduces wear rate when the applied wear load is mall. However, as th load becomes large, the existence of compound layer tends to increase wear rate. The residual stress at the surface of ion-nitrided metal is measured, and the internal stress distribution is calculated when the normal and tangential forces are applied to the surface of metal. Compressive residual stress is largeest at the compound layer, and decreases as the depth from the surface increases. Calculation shows that the maximum stress exists at a certain depth from the surface when normal and tangential force are applied, and that the larger the wear load is the deeper the location of maximum stress becomes. In the analysis, it is found that under small applied wear load the critical depth, where voids and cracks may be created and propagated, is located at the compound layer, as the adhesive wear, where hardness is an important factor, is created the existence of compound layer reduces the amount of wear. When the load becomes large the critical depth is located below the compound layer, and delamination, which may be explained by surface deformation, crack nucleation and propagation, is created, and the existence of compound layer increases wear rate.

• 동력기계공학회지
• /
• 제7권2호
• /
• pp.66-72
• /
• 2003

Recently, the steel parts used at the aerospace and automobile industries are required to be used light weight parts. Therefore, used material, steel have to be a high stress, which is an indispensable condition in this field. At the consideration of parts design, high hardness of the lightweight parts have an benefit of saving fuel and material. A high stress of metal has a point of difference according to the shape of design, external cyclic load and condition of vibration. A crack generates on the surface of metal or under yield stress by defect of inner metal defect or surface defect and slowly, this crack grow stable growth. Finally, rapidity failure phenomena is happen. Fatigue failure_phenomena, which happen in metal, bring on danger in human life and property therefor, anti-fatigue failure technology take an important part of current industries Currently, the shot peening is used for removing the defect from the surface of steel and improving the fatigue strength on surface. Therefore, this paper investigated the effect on frcature toughness using shot peening which is improve the resistance of crack growth and crack expansion rate by fatigue that make a compressive residual stress on surface.

• 한국산업정보학회논문지
• /
• 제17권2호
• /
• pp.73-80
• /
• 2012

산업자동화를 위한 영상처리기술을 활용하여 금속 표면 검사 공정의 육안 검사를 대체하기 위한 장치개발이 요구된다. 본 논문에서는 압연 공정의 금속 판재 표면의 결함을 탐지하기 위하여 이동평균 영상처리기법을 적용한 정밀측정시스템을 제안하였다. 금속 판재의 압연 처리 과정에서 발생하는 표면 패턴이 결함으로 판정될 수 있다. 이러한 경우에 대하여 제안한 시스템을 적용하여 금속 판재 표면의 실제 결함의 수를 측정할 수 있었고 FFT방법에 의한 측정치에 비하여 양호한 결과를 얻었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.12-13
• /
• 2012

An environmentally friendly method for in situ growth of Mg-Al hydrotalcite (HT) film on AZ31 magnesium alloy has been developed. The growth processes and corrosion resistance of the HT film were investigated. Then the HT film was surface modified by phytic acid solution to further improve the corrosion resistance. The film formation involves the dissolution of AZ31 substrate, adsorption of the ions from solution, nucleation of the precursor, followed by the dissolution of $Al^{3+}$, exchanging of $OH^-$ by $CO{_3}^{2-}$ and growth of the HT film. The HT film is very compact and acts as a barrier against $Cl^-$ attack in the early stage of corrosion, and then the surface of the film is dissolved gradually. This dense HT film can provide effective protection to the AZ31 alloy. The HT film with surface modification by phytic acid presents a self-healing feature and exhibits better corrosion resistance.