• Journal of Sensor Science and Technology
• /
• v.27 no.3
• /
• pp.160-164
• /
• 2018

In this paper, a wide dynamic range complementary metal-oxide-semiconductor (CMOS) image sensor with the adjustable sensitivity by using cascode metal-oxide-semiconductor field-effect transistor (MOSFET) and inverter is proposed. The characteristics of the CMOS image sensor were analyzed through experimental results. The proposed active pixel sensor consists of eight transistors operated under various light intensity conditions. The cascode MOSFET is operated as the constant current source. The current generated from the cascode MOSFET varies with the light intensity. The proposed CMOS image sensor has wide dynamic range under the high illumination owing to logarithmic response to the light intensity. In the proposed active pixel sensor, a CMOS inverter is added. The role of the CMOS inverter is to determine either the conventional mode or the wide dynamic range mode. The cascode MOSFET let the current flow the current if the CMOS inverter is turned on. The number of pixels is $140(H){\times}180(V)$ and the CMOS image sensor architecture is composed of a pixel array, multiplexer (MUX), shift registers, and biasing circuits. The sensor was fabricated using $0.35{\mu}m$ 2-poly 4-metal CMOS standard process.

• Journal of Sensor Science and Technology
• /
• v.31 no.3
• /
• pp.151-155
• /
• 2022

In this paper, we present a highly-sensitive gate/body-tied (GBT) metal-oxide semiconductor field-effect transistor (MOSFET)-type photodetector using multi-finger structure whose photocurrent increases in proportion to the number of fingers. The drain current that flows through a MOSFET using multi-finger structure is proportional to the number of fingers. This study intends to confirm that the photocurrent of a GBT MOSFET-type photodetector that uses the proposed multi-finger structure is larger than the photocurrent per unit area of the existing GBT MOSFET-type photodetectors. Analysis and measurement of a GBT MOSFET-type photodetector that utilizes a multi-finger structure confirmed that photocurrent increases in ratio to the number of fingers. In addition, the characteristics of the photocurrent in relation to the optical power were measured. In order to determine the influence of the incident the wavelength of light, the photocurrent was recorded as the incident the wavelength of light varied over a range of 405 to 980 nm. A highly-sensitive GBT MOSFET-type photodetector with multi-finger structure was designed and fabricated by using the Taiwan semiconductor manufacturing company (TSMC) complementary metal-oxide-semiconductor (CMOS) 0.18 um 1-poly 6-metal process and its characteristics have been measured.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.102-103
• /
• 2013

As an important p-type semiconductor metal oxide with a narrow band gap (1.2 - 2.6eV), copper oxide (Cu2O) has been studied because of its various applications as material for heterogeneous catalysts, gas sensors, optical switch, lithium-ion electrode materials, field emission devices, solar cells. The fundamental properties of oxide-semiconductor can be greatly affected by the surface morphology, size, geometry and spatial orientation.

• Journal of Powder Materials
• /
• v.26 no.1
• /
• pp.28-33
• /
• 2019

The gas sensor is essential to monitoring dangerous gases in our environment. Metal oxide (MO) gas sensors are primarily utilized for flammable, toxic and organic gases and $O_3$ because of their high sensitivity, high response and high stability. Tungsten oxides ($WO_3$) have versatile applications, particularly for gas sensor applications because of the wide bandgap and stability of $WO_3$. Nanosize $WO_3$ are synthesized using the hydrothermal method. As-prepared $WO_3$ nanopowders are in the form of nanorods and nanorulers. The crystal structure is hexagonal tungsten bronze ($MxWO_3$, x =< 0.33), characterized as a tunnel structure that accommodates alkali ions and the phase stabilizer. A gas detection test reveals that $WO_3$ can detect acetone, butanol, ethanol, and gasoline. This is the first study to report this capability of $WO_3$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.281.2-281.2
• /
• 2013

Since heavy metal ions included in water or food resources have critical effects on human health, highly sensitive, rapid and selective analysis for heavy metal detection has been extensively explored by means of electrochemical, optical and colorimetric methods. For example, quantum dots (QDs), such as semiconductor QDs, have received enormous attention due to extraordinary optical properties including high fluorescence intensity and its narrow emission peaks, and have been utilized for heavy metal ion detection. However, the semiconductor QDs have a drawback of serious toxicity derived from cadmium, lead and other lethal elements, thereby limiting its application in the environmental screening system. On the other hand, Graphene oxide (GO) has proven its superlative properties of biocompatibility, unique photoluminescence (PL), good quenching efficiency and facile surface modification. Recently, the size of GO was controlled to a few nanometers, enhancing its optical properties to be applied for biological or chemical sensors. Interestingly, the presence of various oxygenous functional groups of GO contributes to opening the band gap of graphene, resulting in a unique PL emission pattern, and the control of the sp2 domain in the sp3 matrix of GO can tune the PL intensity as well as the PL emission wavelength. Herein, we reported a photoluminescent GO array on which heavy metal ion-specific DNA aptamers were immobilized, and sensitive and multiplex heavy metal ion detection was performed utilizing fluorescence resonance energy transfer (FRET) between the photoluminescent monolayered GO and the captured metal ion.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.4
• /
• pp.189-195
• /
• 2016

Micro Hotplate (MHP) is the key component in micro-sensors, particularly gas sensors. Indeed, in metal oxide gas sensors MOX, micro-heater is used as a hotplate in order to control the temperature of the sensing layer which should be in the requisite temperature range over the heater area, so as to detect the resistive changes as a function of varying concentration of different gases. Hence, their design is a very important aspect. In this paper, we have presented the design and simulation results of a meander micro heater based on three different materials - platinum, titanium and tungsten. The dielectric membrane size is 1.4 mm × 1.6 mm with a thickness of 1.4 μm. Above the membrane, a meander heating film was deposed with a thickness of 100 nm. In order to optimize the geometry, a comparative study by simulating two different heater thicknesses, then two inter track widths has also been presented. Power consumption and temperature distribution were determined in the micro heater´s structure over a supply voltage of 5, 6, and 7 V.

• Journal of the Korean Society of Tobacco Science
• /
• v.35 no.1
• /
• pp.20-27
• /
• 2013

An Electronic Nose(E-Nose) and Gas Chromatography/Mass Spectroscopy (GC/MS) are meanwhile conventional technique to analyze volatile materials in many industries (e.g., food, medicine, environment) and have broad acceptance in the analysis of tobacco products. In this study, an experiment where tin oxide gas sensor array responses and GC/MS profiles are used to characterize the volatile compounds of different cigarettes at the same time is performed and the measurements of two instruments are compared for cigarette samples with a known chemical information. E-Nose and GC/MS were employed to differentiate and match flavored cigarettes with commercial tobacco flavoring agents (lavender, vanilla, peppermint, orange, star anise). For verifying reliability of two systems, the analyses were conducted in terms of amount of flavors in each cigarettes using partial least squares (PLS) and with the principal components analysis (PCA). Various chemical sensors and GC/MS data was reduced into two principal factors (PC1, PC2) for being distinguished with visualized regions. Both systems provided adequate results for odor characteristics of cigarettes in this study with each instrument having its own advantages and disadvantages.

• Journal of Sensor Science and Technology
• /
• v.26 no.3
• /
• pp.204-208
• /
• 2017

Highly uniform and well-dispersed Zeolitic Imidazolate Framework-7 (ZIF-7) particles were prepared by the precipitation of $Zn^{2+}$ using benzimidazole, which were converted into ZnO nanoparticles by heat treatment at $500^{\circ}C$ for 24 h. The ZIF-7 derived ZnO nanoparticles showed abundant mesopores, high surface area, and good dispersion. The gas sensing characteristics toward 5 ppm acetone, ethanol, trimethylamine, ammonia, p-xylene, toluene, benzene, and carbon monoxide and carbon dioxide were investigated at $350-450^{\circ}C$. ZIF-7 derived ZnO nanoparticles exhibited high response to 5 ppm acetone ($R_a/R_g=57.6$; $R_a$: resistance under exposure to the air, Rg: resistance under exposure to the gas) at $450^{\circ}C$ and negligible cross-responses to other interference gases (trimethylamine, ammonia, p-xylene, toluene, benzene, carbon monoxide, carbon dioxide) and relatively low responses to ethanol. ZIF derived synthesis of metal oxide nanoparticles can be used to design high performance acetone sensors.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.12
• /
• pp.1178-1184
• /
• 2015

In conventional robotics, charge-coupled device (CCD) and complementary metal-oxide-semiconductor (CMOS) cameras have been utilized for acquiring vision information. These devices have problems, such as narrow optic angles and inefficiencies in visual information processing. Recently, biomimetic vision sensors for robotic applications have been receiving much attention. These sensors are more efficient than conventional vision sensors in terms of the optic angle, power consumption, dynamic range, and redundancy suppression. This paper presents recent research trends on biomimetic vision sensors and discusses future directions.

• Korean Journal of Food Science and Technology
• /
• v.34 no.1
• /
• pp.136-139
• /
• 2002

The discrimination of the agricultural origin, especially locally produced of imported products such as black rices was investigated by using electronic nose. Volatile components from these products were discriminated by six metal oxide sensors without pretreatment. Pattern recognition was carried out. Principal component analysis showed the differences between imported and locally produced ones. The number of 57 from 69 species of black rices were recognized as locally produced one (83.33%) and 11 from 13 species one (imported black rices) was correctly discriminated. Unknown habitat of black rice could be identified by artificial neural network system whether the imported or not. Also commercial electronic nose (E-nose 5000) that was combined with metal oxide sensor and conducting polymer sensor showed 92.75% (locally produced black rices) and 92.31% (imported one) of discrimination.