• Journal of the Korean Ceramic Society
• /
• v.22 no.3
• /
• pp.29-34
• /
• 1985

The IR spectra of he heavy metal fluoride glasses showed peaks at $1, 400cm^{-1}$ or $1, 100cm^{-1}$ due to metal oxyfluoride impurities. The intensity of this band and hence the oxide impurity content of the glass could be reduced considerably by the use of reactive atmosphere melting under $CCl_4$ In comparison with the fundamental IR absorption band of heavy metal oxides the oxide impurity bands observed in the heavy metal fluoride glasses are multiphonon bands due to a 2-phonon absorption process. The envelope of the a vs. v curve beyond thue fundamental region shows the exponential fall off of a with increasing v-typical of intrinsic multiphonon absorption. In the multiphonon region the amount of structure is intermediate between that observed for covalent solids and that for ionic solids.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.771-772
• /
• 2006

Mechanical properties of metal injection molded titanium and titanium alloy parts were investigated in this study. Material powders with low oxygen content and spherical shape were obtained by electrode induction-melting gas atomization which could melt and atomize titanium and titanium alloy bars with no touch on crucible or tundish. Tensile specimens were fabricated from obtained powders by metal injection molding process. Tensile strength of the specimens increases with increasing oxygen content. This result corresponds to a tendency of wrought metal.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.74-78
• /
• 2003

In this paper, we studied, by numerical calculation, a system, which was composed of metal-film and metal-substrate irradiated by IPIB with beam ion energy 250 keV, current density 10 to 250 A/$\textrm{cm}^2$. While the IPIB irradiation was going on, an induced effect named mixing occurred. In this case, metal-film and part of metal-substrate melted and mixed. The mixing state was kept as it was in melting phase due to the fast cooling rate. Our works were simulating the heating and cooling process via our STEIPIB program and tried to find proper parameters for a specific film-substrate system, 500 nmtitanium film coated on aluminum, to get best mixing results. The parameters calculated for such Ti-Al system were compared with the experimental results and were in good accordance to the experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.814-819
• /
• 2000

The progress in the field of electronic materials has been especially significant for applications involving a range of electrical properties. Its importance is increasing with the increasing demand for integrated circuits. The sol-gel technique has been used for many years, and the metal alkoxides have featured prominently as source materials. The method consist of making a homogeneous solution of the component metal alkoxides in a suitable solvent, usually the parent alcohol; and then causing the hydrolysis under controlled conditions to produce a gel containing the hydrated metal oxide. The gel is then dried, and fired to produce a ceramic or glassy material at a temperature much lower than that required by the conventional melting process. This project consists of important theoretical considerations, processing techniques and applications related to electrophoresis derived thin films. In the electrophoretic process a metal alkoxide solution is gelled through hydrolysis-polymerization and converted the gel thin layer to an oxide by heating at relatively low temperatures.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.136-141
• /
• 2012

'Jikjisimcheyocheal (Jikji afterwards)' is known as a first book printed by the metal type in the world. The metal type used for printing this book has not been found yet. To help for replicating the original metal type, it is required to investigate the composition analysis of the copied metal type. In this study, the composition analysis and thermodynamic care for replicating of ancient metal type was performed on the basis of an analytical reports concerned with the ancient metal type which made after Jikji printing. Metal types were made by remelting and casting of the mother alloy which came from a cast of a mixed metals in accordance with the composition revealed in the literatures. Change of composition during remelting of mother alloy and casting of metal was detected by the EDS analysis. The reasons for variation in composition were discussed by metallurgical and thermodynamic point of view, and a mixing ratio of metals to get the original composition of ancient metal type is suggested. Some attention should be paid on mixing, melting and casting of metals to get an objected composition for copy of ancient metal type.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.19 no.2
• /
• pp.233-241
• /
• 2021

A series of three bench-scale experiments was performed to investigate the conversion of sodium metal to sodium chloride via reactions with non-metal and metal chlorides. Specifically, batches of molten sodium metal were separately contacted with ammonium chloride and ferrous chloride to form sodium chloride in both cases along with iron in the latter case. Additional ferrous chloride was added to two of the three batches to form low melting point consolidated mixtures of sodium chloride and ferrous chloride, whereas consolidation of a sodium-chloride product was performed in a separate batch. Samples of the products were characterized via X-ray diffraction to identify attendant compounds. The reaction of sodium metal with metered ammonium chloride particulate feeds proceeded without reaction excursions and produced pure colorless sodium chloride. The reaction of sodium metal with ferrous chloride yielded occasional reaction excursions as evidenced by temperature spikes and fuming ferrous chloride, producing a dark salt-metal mixture. This investigation into a method for controlled conversion of sodium metal to sodium chloride is particularly applicable to sodium containing elevated levels of radioactivity-including bond sodium from nuclear fuels-in remote-handled inert-atmosphere environments.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.421-422
• /
• 2009

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2012.06a
• /
• pp.172-172
• /
• 2012

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.11a
• /
• pp.323-324
• /
• 2018

• Resources Recycling
• /
• v.20 no.2
• /
• pp.74-81
• /
• 2011

The dry method and wet method are currently used for the recovery of platinum group metals (Pt, Rh, Pd) contained in spent automobile catalysts. The study herein aims to identify the melting condition and optimum collector metal in accordance with a comparison of each concentration change in melting waste catalysts, using Fe and Cu in a basic experiment to recover waste catalysts through application of the dry melting method. As a summarized result of the experiment herein, it was determined to be more advantageous to use Fe as a parent material rather than Cu from the aspect of recollection rate, and the concentration change rate of platinum group metals within slag was greatly enhanced at $1,600^{\circ}C$ melting condition rather than at $1,500^{\circ}C$ in terms of melting processing temperature. The mean concentration of platinum group metals - Rh, Pd and Pt - within slag after a melting process at $1,600^{\circ}C$ were 6.21 ppm, 5.98 ppm and 6.97 ppm. The Rh and Pd were 50.58% and 55.31% respectively greater than the concentration change rate of platinum group metals in slag at a melting temperature of $1,500^{\circ}C$. However, since the initial concentration of Pt within the waste catalysts was 12.9 ppm, is relatively low, it was difficult to compare concentration change rates after the melting process.