• 공업화학
• /
• 제25권2호
• /
• pp.198-203
• /
• 2014

본 연구에서는 Ni metal foam 플레이트의 수증기 개질반응 및 표면 특성을 조사하였다. 전처리를 통하여 Ni의 산화상태를 변화시킬 수 있었으며, 활성 site로서 표면에 노출된 metallic Ni 종은 수증기 개질 반응활성에 중요한 역할을 한다. 또한 Ni metal foam 플레이트의 기공제어 및 촉매 기능을 부여하기 위하여 Ni metal foam 플레이트와 Ni-YSZ 촉매를 혼합하여 다공성 촉매 분리막을 제조하였다. SEM 분석 결과 metal foam 플레이트의 기공을 제어할 수 있었으며, 표면에 Ni-YSZ 촉매는 고르게 잘 분포되어 있었다. Ni 기반 다공성 촉매 분리막은 공간속도에 상관없이 상용촉매와 유사한 수증기 개질 활성을 가진다.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.116-125
• /
• 1997

Electron beam weldability of 9%Ni steels has been investigated to apply EBW to the construction of LNG storage tank. While mechanical properties of welded joints were satisfied by ASTM specification, impact energy of weld metal was as low as 27 - 55J at $-196^{\circ}C$. As the result of Ni wires inserted at the joint to be welded, Ni content of weld metal was increased to about 10%, resulting on the improvement of impact toughness to 110 ~ 120J at $-196^{\circ}C$. This improvement of impact toughness in weld metal was due to the formation of tempered martensite and retained austenite. Above results indicate that, if Ni content of weld metal was increased about 10% by Ni wires addition, electron beam welded 9%Ni steels weld metal had sufficient impact energy necessary for a LNG storage tank.

• 청정기술
• /
• 제28권2호
• /
• pp.154-162
• /
• 2022

알루미늄 (Al) 금속을 전구체 및 구조체로 이용, 수열 반응을 통하여 Al@Al₂O₃와 Al@Ni-Al LDH (LDH = layered double hydroxide) 코어-쉘 복합 구조체를 합성하였다. 제조된 구조체의 형상, 조성, 결정 구조는 수용액에 존재하는 이온들에 의하여 크게 영향을 받았으며, 이를 활용하여 다양한 특성의 촉매 구조체 유도가 가능하였다. Al@Ni-Al LDH 코어-쉘 구조체의 환원을 통하여 Ni 나노 입자가 고정화된 Ni/Al@Al₂O₃ 촉매를 제조하였고, CO₂ 메탄화 반응에 적용하여 촉매의 특성을 평가하였다. Ni/Al@Al₂O₃ 촉매는 전통적 incipient wetness impregnation 방법에 의하여 제조된 Ni/Al₂O₃ 촉매에 비교하여 Ni 입자의 분산도와 균일성이 매우 높았으며 약 2 배 이상의 CO₂ 전환율로 높은 촉매적 활성과 더불어 구조의 안정성을 보여 주었다. 이러한 Ni/Al@Al₂O₃ 구조체 촉매의 우수한 특성은 Al 금속을 기반으로 한 새로운 개념의 촉매 구조체 설계와 합성 방법의 타당성을 보여준다.

• 한국재료학회지
• /
• 제24권8호
• /
• pp.393-400
• /
• 2014

NiO catalysts were successfully coated onto FeCrAl metal alloy foam as a catalyst support via a dip-coating method. To demonstrate the optimum amount of NiO catalyst on the FeCrAl metal alloy foam, the molar concentration of the Ni precursor in a coating solution was controlled, with five different amounts of 0.4 M, 0.6 M, 0.8 M, 1.0 M, and 1.2 M for a dip-coating process. The structural, morphological, and chemical bonding properties of the NiO-catalyst-coated FeCrAl metal alloy foam samples were assessed by means of field-emission scanning electron microscopy(FESEM), scanning electron microscopy-energy dispersive spectroscopy(SEM-EDS), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS). In particular, when the FeCrAl metal alloy foam samples were coated using a coating solution with a 0.8 M Ni precursor, well-dispersed NiO catalysts on the FeCrAl metal alloy foam compared to the other samples were confirmed. Also, the XPS results exhibited the chemical bonding states of the NiO phases and the FeCrAl metal alloy foam. The results showed that a dip-coating method is one of best ways to coat well-dispersed NiO catalysts onto FeCrAl metal alloy foam.

• 대한치과기공학회지
• /
• 제34권4호
• /
• pp.337-344
• /
• 2012

Purpose: This study examined the corrosion level by alloy type and pH, and used the corrosion levels as the dental health data. The study utilized one Ni-Cr alloy for the full and removable partial denture metal frameworks and two Ni-Cr alloys for porcelain-fused-to-metal crown, among the non-beryllium dental casting non-precious Ni-Cr alloys. Methods: The alloy specimens were manufactured in $10cm^2$ and stored in the corrosive solution(pH 2.2-4.4) in the electrical water bath($37^{\circ}C$) for seven days. Afterwards, the metal ions were quantitatively analyzed using the ICP. Results: Of the three metal alloys, Bellabond-Plus$^{(R)}$alloy and SOLIBOND N$^{(R)}$alloy, with 22% or higher chrome chemical contents, had higher corrosion resistance than Jdium-100$^{(R)}$alloy with 20% chrome chemical content. In all three alloys, the corrosion of Ni was highest, and metal ion corrosion was higher in the pH 2.2 corrosive solution. Conclusion: Although Ni-Cr alloy was not very corrosive, a Ni-allergic patient should not have Ni-Cr alloy prosthesis. The Ni-Cr alloy for porcelain-fused-to-metal crown should be designed for the dental porcelain to cover the whole crown.

• Journal of Welding and Joining
• /
• 제14권1호
• /
• pp.47-56
• /
• 1996

The purpose of this study is to develope an insert metal which can be brazed at lower temperature than the conventionally used insert metal and provide higher strength joint than base metal. In the review of binary phase diagram concerning Ti, Cu and Ni resulted in the discovery of Si having eutectic composition with them. The microstructure and the distribution of elements in reaction zone between CP Ti and insert metal were investigated by Optical Microscopy, SEM/EDX, EPMA, X-RAY. The newly developed insert metal is Ti-15wt%Cu-18wt%Ni-2wt%Si, which can yield the lower brazing temperature(1183K) compared with the conventional Ti-Cu-Ni system insert metal. The joints with this insert metal had tensile strength of 385MPa in the bonding temperature range of 1183K to 1243K.

• 대한치과기공학회지
• /
• 제35권4호
• /
• pp.359-364
• /
• 2013

Purpose: This study was to observe characteristic of metal oxidation and bonding strength according to composition of Ni-Cr alloy for porcelain fused to metal crown. The three kinds of Ni-Cr alloy with different composition ratio of parent metal were observed general properties and chemical properties of each alloy surface and measured the shear bonding strength between ceramic and each alloys. The aim of study was to suggest the material for design of parent metal's composition ratio to development of alloy for porcelain fused to metal crown. Methods: The three kinds of alloy as test specimen was Ni(59wt%)-Cr(24wt%), Ni(67wt.%)-Cr(16wt.%) alloy and Ni(71wt%)-Cr(12wt%)alloy. The oxide on surface was observed by EDX. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{59}Cr_{24}$ alloy measured 23.03wt%, $Ni_{67}Cr_{16}$ alloy measured 21.13wt% and $Ni_{71}Cr_{12}$ alloy was measured 48.55wt%. And the maximum shear bonding strength was measured 58.02Mpa between $Ni_{59}Cr_{24}$ alloy and vintage halo(H2 group). Conclusion: The surface property and oxide characteristic three kind of Ni-Cr alloy was similar. and shear bonding strength showed the highest bonding strength in H2 specimens.

• Bulletin of the Korean Chemical Society
• /
• 제27권12호
• /
• pp.2045-2050
• /
• 2006

The interstitial hydrogen bonding in NiTi solid and its effect on the metal-to-metal bond is investigated by means of the EH tight-binding method. Electronic structures of octahedral clusters $Ti_4Ni_2$ with and without hydrogen in their centers are also calculated using the cluster model. The metal d states that interact with H 1s are mainly metal-metal bonding. The metal-metal bond strength is diminished as the new metal-hydrogen bond is formed. The causes of this bond weakening are analyzed in detail.

• 대한치과기공학회지
• /
• 제37권1호
• /
• pp.23-29
• /
• 2015

Purpose: The selective laser melting (SLM) process for dentistry, which is one of the additive manufacturing technologies (AM) allows for rapid production of a three-dimensional model with complex shape by directly melting metal powder. This process generates detailed items of a three-dimensional model shape through consolidation of a thin powder layer by utilizing both selective melting and laser beam simultaneously. In regard to SLM process, Fe-base powder, Ti-6AI-4V powder, AI-base powder, etc. have been researched. It is believed that the aforementioned technologies will be widely utilized in manufacturing metal parts using metal powder of raw material. This study chose Ni-Cr-Mo metal powder in order to manufacture metal powder materials that would be used in the selective laser melting for dentistry. Methods: This study manufactured metal powder using mechanical alloying technique (MA) among those metal powder manufacturing techniques. Moreover, this study aimed to utilize the metal powder manufactured after observing the characteristics of powder as preliminary data of Ni-Cr-Mo metal powder. This study could obtain the following conclusions within the experimental limitations. Results: As a result of mechanically alloying Ni-Cr-Mo powder over time, its mean particle size was $66.93{\mu}m$ $54.4{\mu}m$ and $45.39{\mu}m$ at 10h, 20h and 30h, respectively. The gtain form of metal powder by mechanical alloying technique was a sponge-like shape of irregular plate; however, the gtain form manufactured by high-pressure water aromization process had the following three types: globular type, chain type and oval type. Conclusion: This study found $37.65{\mu}m$ as the mean particle size of Ni-Cr-Mo metal powder, which was manufactured using water atomization technique under the following conditions: water atomization flux of 300 liter/min, hydraulic pressure of $400kgf/cm^2$ and injection angle of $45^{\circ}$. This study confirmed that the grain form of powder (solid particle form) would vary depending on the manufacturing process.

• Bulletin of the Korean Chemical Society
• /
• 제12권5호
• /
• pp.574-582
• /
• 1991

The CO molecules adsorbed on Ni(111) surface is studied in the cluster approximation employing EH method with self-consistent charge iteration. The effect of CO coverage is simulated by allowing the variation of valence state ionization potentials of each Ni atom in model cluster according to the self-consistent charge iteration method. The CO coverage dependent C-O stretching frequency shift, adsorption site conversion, and metal work function change are attributed to the charge transfer between metal surface and adsorbate. For CO/Ni(111) system, net charge transfer from Ni surface to chemisorbed CO molecules makes surface Ni atoms be more positive with increasing coverage, and lowers Ni surface valence band. This leads to a weaker interaction between metal surface valence band and Co $2{\pi}^{\ast}$ MO, less charge transfer to a single CO molecule, and the bule shift of C-O stretching frequency. Further increase of coverage induces the conversion of 3-fold site CO to lower coordination site CO as well as the blue shift of C-O stretching frequency. This whole process is accompanied by the continuous increase of metal work function.