• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1095-1101
• /
• 2002

An experimental apparatus was prepared to investigate thermal and hydrodynamic characteristics of regenerator at cryogenic temperature under pulsating pressure condition. The regenerator was pressurized and depressurized by a compressor with various operating frequencies. Cold end of the regenerator was maintained around 100 K by means of a liquid nitrogen heat exchanger. Instantaneous gas temperature and mass flow rate were measured at both ends of the regenerator during the whole pressure cycle. Pulsating pressure drop across the regenerator was also measured to see if it could be predicted by a friction factor at steady flow condition. The operating frequency of pressure cycle was varied between 3 and 60 Hz, which are typical operating frequencies of Gifford-McMahon, pulse tube, and Stilting cryocoolers. First, the measured friction factor for typical wire screen mesh regenerator was nearly same as steady flow friction factor for maximum oscillating Reynolds number up to 100 at less than 9 Hz. For 60 Hz operations, however, the discrepancy between oscillating flow friction factor and steady flow one was noticeable if Reynolds number was higher than 50. Second, the ineffectiveness of regenerator was directly calculated from experimental data when the cold-end was maintained around 100 K and the warm-end around 293 K, which simulates an actual operating condition of cryogenic regenerator. Influence of the operating frequency on ineffectiveness was discussed at low frequency range.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.631-637
• /
• 2013

The characteristics of involute gear pump with eccentric gap between gear tip and housing have been studied in terms of volumetric flow rate and/or flow efficiency. The analysis has been done with FLUENT/R-13 employing with k-e model for the turbulent flow under the given conditions of rotational velocity, gap distance and outlet pressure. The effect of parameters continues to be shown for the eccentric gear as same as for the concentric gear such that the volumetric flow rate (volumetric efficiency) increases as the increases of rotational velocity and decrease of gap distance and of outlet pressure. In the meantime, the shape of pressure build-up appears to be exponentially increase as gap distance decreases at upstream position. The pressure is rapidly developing in the upstream and remains almost constant thereafter in the downstream of circumferential flow path. This typical characteristics becomes more profound as eccentricity increases. The pump performance for the eccentric gear pump with minimum gap distance shows better than its concentric counterpart. However, it shows not for the concentric pump with minimum gap distance. Therefore, the gap reduction due to eccentricity may be positive for pump performance.

• Korea-Australia Rheology Journal
• /
• v.15 no.3
• /
• pp.131-150
• /
• 2003

A new numerical algorithm of finite element methods is presented to solve high Deborah number flow problems with geometric singularities. The steady inertialess planar 4 : 1 contraction flow is chosen for its test. As a viscoelastic constitutive equation, we have applied the globally stable (dissipative and Hadamard stable) Leonov model that can also properly accommodate important nonlinear viscoelastic phenomena. The streamline upwinding method with discrete elastic-viscous stress splitting is incorporated. New interpolation functions classified as rational interpolation, an alternative formalism to enhance numerical convergence at high Deborah number, are implemented not for the whole set of finite elements but for a few elements attached to the entrance comer, where stress singularity seems to exist. The rational interpolation scheme contains one arbitrary parameter b that controls the singular behavior of the rational functions, and its value is specified to yield the best stabilization effect. The new interpolation method raises the limit of Deborah number by 2∼5 times. Therefore on average, we can obtain convergent solution up to the Deborah number of 200 for which the comer vortex size reaches 1.6 times of the half width of the upstream reservoir. Examining spatial violation of the positive definiteness of the elastic strain tensor, we conjecture that the stabilization effect results from the peculiar behavior of rational functions identified as steep gradient on one domain boundary and linear slope on the other. Whereas the rational interpolation of both elastic strain and velocity distorts solutions significantly, it is shown that the variation of solutions incurred by rational interpolation only of the elastic strain is almost negligible. It is also verified that the rational interpolation deteriorates speed of convergence with respect to mesh refinement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.840-843
• /
• 2002

The dry pulverizing/Mixing device is used to deal with the spent fuels for the safe disposal. The separated pellets from hulls by a slitting device are put and oxidized from UO$_2$ solid pellet to U$_3$O$\_$8/ powder in the device. The device have been developed based on a voloxidation method which is one of several dry de-cladding methods. We have benchmarked dry de-cladding methods, analyzed applicability to the advanced spent fuel management process, integrated and compared several configuration, and finally derived detailed specifications proper to requirements for the device. Also, thermal characteristics of the device such as thermal stress and strain have been analyzed by the commercial software, 1-DEAS, and the reliability of the results have been verified by the KOLAS(Korea Laboratory Accreditation Scheme). The UO$_2$ solid pellets are put in the device which has a capacity of 20 kgHM per a batch, heated up about 600$^{\circ}C$ in the air environment. Then, the UO$_2$ solid pellets are oxidized into the U$_3$O$\_$8/ powder, and the powder is collected in a special vessel. The device has been designed and developed as fellows: the multi-staged fine hole meshes are used to reduce the size of the powder gradually, heat and air(oxygen) are supplied continuously to reduce the reaction time, and slight vibration effect are applied to collect powder cling to the device.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.28 no.6
• /
• pp.586-589
• /
• 2006

Deep circumflex iliac artery (DCIA) flap can be harvested as a composite free flap and is often used to adequately reconstruct wide mandibular defects. However, the harvesting of this DCIA flap can result in severe osseous defect of the donor site causing a morphologic defect in the iliac crest. To reconstruct this defect of the iliac donor site, several innovative techniques using bioactive ceramic spacers, autogenous rib bone, polylactic acid mesh, or titanium plates have been introduced. Nonetheless, these methods have not been widely used due to high cost, secondary donor site morbidity, difficulty of use, and postoperative dissatisfaction. We used two titanium plates to reconstruct the donor iliac site defect at the harvesting time of primary DCIA flap surgery in the 30-year old female with an ameloblastoma in the left mandible. Postoperatively, both iliac sites were relatively balanced and there were few complications. At the 2 years follow-up, there were no specific abnormal radiographic findings and the patient was very satisfied with her esthetic iliac contouring. In our report, we evaluate the effect of two titanium plates on the reconstruction of the iliac donor site in the aspects of esthetics and usefulness. This technique has many advantages, such as reduced cost, simplicity, decreased postoperative pain or discomfort, and improved bilateral balance of both anterior iliac crest contours, especially in young female patients.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.7 s.155
• /
• pp.1090-1102
• /
• 2006

The purpose of this study is to develop an improved work clothing which is much safe, comfortable, mobility and convenient than what workers currently wear at construction site. The investigation has been conducted to evaluate current work clothing to grasp any problems, discomforts and damages related to the work clothing. For the best and accurate data, hands-on investigation and a short-interview have been performed at the construction site as well as formulating a questionnaire. The questionnaires was answered by 425 workers and safety manager of 13 different construction site. The result of the questionnaire enables us to design a sample work clothing, many pa π s such as material, pattern and design have been improved. To improve the amenity of heat, the surface of a material was used by $Aerocool^{\circledR}$ fiber which contains inside dryness function. In order to absorb perspiration on the back the armpits, mesh martial that is mixture of $Coolever^{TM}$ fiber and $Mirawave^{TM}$ fiber was used to absorb perspiration in an effective manner. And a sleeve's bottom part and trousers' bottom part's cover method have been changed. Sample work clothing was shorten at the side of upper garment up to 2cm and lengthen the length of the back by 3cm. To reduce the tightness around armpit more room was given in that area. Darts were added to the elbow, the hip, and the knees that also followed an ergonomic pattern. A sample work clothing evaluated an objective assessment and subjective assessment to compare to a current work clothing. Assessment group consists of seven subject groups and nine expert groups to evaluate external appearance and adaptability to the movements. In all aspects of the test, the result of evaluation process of the sample work clothing received more positive assessment than the current work clothing.

• Korean Journal of Food Science and Technology
• /
• v.10 no.2
• /
• pp.209-214
• /
• 1978

Naringinase produced from Aspergillus nidulans was immobilized in acrylamide gel by the entrapping method and its characteristics were studied. Optimum acrylamide concentration was 10%, but N.N'-methylene bisacrylamide concentration had no influence on the final enzyme gel activity. The suitable amount of enzyme dissolved in the polymerization reaction mixture was 126 units/ml. Optimum pH of immobilized enzyme was 5.0 which was the same as that of free enzyme. However, immobilized enzyme showed a higher optumum reaction temperature, markedly increased pH and temperature stability. In a packed-column reactor, the observed reaction rate was increased proportionally to flow rate up to 5ml/min., but independent above 6ml/min.. Activation energy of the immobilized enzyme was 13.01 Kcal/mole, and the energy required for the thermal inactivation was 39.4 Kcal/mole. The apparent Km for 100 mesh gel was $7.23{\times}10^{-3}$ mole.

• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.3
• /
• pp.317-324
• /
• 2013

This research assessed the surface properties of modified activated carbons with three different acids and five different metals for ammonia gas removal. Raw bituminous coal-based activated carbon ($4{\times}8$ mesh) had low adsorption capacity of 0.72 mg $NH_3/g$ based on the analysis in the column adsorption experiment. Adsorption capacities of carbons modified with $CH_3COOH$, $H_3PO_4$, and $H_2SO_4$ increased up to 3.34, 21.00, and 35.21 mg $NH_3/g$, respectively. Those of carbons with Cu, Zn, Zr, Fe, and Sn were 9.63, 9.13, 7.09, 25.12 and 15.03 mg $NH_3/g$. Ammonia adsorption was enhanced by the presence of surface oxygen groups on carbon materials, which influenced pH of carbon surface. BET surface area of raw carbon was analyzed to be $1087m^2/g$, but it decreased by carbon surface modification. Fe-impregnated carbon showed $503.02m^2/g$ of surface area. These observations were mostly caused by chemical adsorption.

• Ocean and Polar Research
• /
• v.26 no.2
• /
• pp.367-376
• /
• 2004

Macrobenthos were collected at 7 stations located from $5^{\circ}N$ to $10^{\circ}N$ with 1o interval along the longitude of $131^{\circ}W$ using a box corer with sampling area of $0.25\;m^2$ in July, 1999. In order to see the vertical distribution of macrobenthos in sediments, each subcore sample was divided into 5 layers with 1 cm interval up to 6 cm depth. Each subcore sample was sieved through 0.3 mm mesh screen and fixed with 10% Rose Bengal added formalin. A total of 22 faunal groups in 11 phyla were sampled and the average density was $959\;{\pm}\;584\;ind./m^2$. Foraminiferans comprised 34.8% of total specimens were the most abundant fauna, and followed by nematodes (27.5%), polychaete worms (15.7%), and benthic harpactoid copepods (10.4%). A latitudinal trend was shown in the distribution of macrobenthos; the maximum density of $1,832\;ind./m^2$ appeared at station N06 and the most poverished community occurred at station N09 with the density of $248\;ind./m^2$. The density of typical macrofaunal taxa except foraminiferans and nematods was $116\;ind./m^2$. In the vertical distribution of macrobenthos, more than 70% of macrobenthos occurred in the upper 2 cm layer, and upper 4 cm layer contained about 90% of macrofauna. Polychaete worms consisted of 22 families, and cirratulid and paraonid worms were dominant polychaete species. The prominant feeding guilds of polychaete worms were SDT (surface, descretely motile, tenaculate feeding) and SMX (surface, motile, non-jawed); they comprised more than 50% of polychaete abundance. These feeding guilds of polychaete worms suggests that the deep sea benthos should be well adapted the newly settled deposits from water column, but this should be clarified by the further studies.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.3
• /
• pp.15-22
• /
• 2012

For the construction of safe and clear urban environment, it is necessary that we identify the rubbish waste volume and we know the accuracy volume. In this paper, we developed the algorithm which computes the waste volume using the stereo camera for enhancing the environment of waste repository. Using the stereo vision camera, we first computed the distortion parameters of stereo camera and then we obtained the points cloud of the object surface by measuring the target object. Regarding the points cloud as the input of the volume calculation algorithm, we obtained the waste volume of the target object. For this purpose, we suggested two volume calculation algorithm based on the uniform meshing method. The difference between the measured volume such as today's one and yesterday's one gives the reposit of waste volume. Using this approach, we can get the change of the waste volume repository by reading the volume reports weekly, monthly and yearly, so we can get quantitative statistics report of waste volume.