• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11B
• /
• pp.1272-1282
• /
• 2009

This paper consists of two parts: the protocol for tag-to-tag mesh network and the implementation of dual-radio RFID system. Recently, RFID has been adopted in ports or warehouse, being attached to containers and palettes for loading/unloading automation. However, the RFID system has encountered one problem - some tags cannot receive any command from reader intermittently due to signal interference by containers or field equipments (e. g. cranes and yard tractors). This area where reader signal cannot reach is called dead-zone. The proposed method for solving the dead-zone problem is as follows. A zone which can be communicated directly between readers and tags communicates in 433MHz frequency band in compliance with ISO/IEC 18000-7 standard. On the other hand, dead-zone communicates in 2.4GHz frequency band by using tag-to-tag mesh network in compliance with IEEE 802.15.4 standard. The proposed method can not only save much cost to install additional readers but also help resolve the dead-zone problem. Furthermore, it can provide the easier, faster, and more economical network infrastructure.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.202-207
• /
• 2004

An elastic-plastic finite element analysis of fatigue crack closure is performed for plane strain conditions. The stabilization behavior of crack opening level and the effect of mesh size on the crack opening stress are investigated. In order to obtain a stabilized crack opening level for plane strain conditions, the crack must be advanced through approximately four times the initial monotonic plastic zone. The crack opening load tends to increase with the decrease of mesh size. The mesh size nearly equal to the theoretical plane strain cyclic plastic zone size may provide reasonable numerical results comparable with experimental crack opening data. The crack opening behavior is influenced by the crack growth increment and discontinuous opening behavior is observed. A procedure to predict the most appropriate mesh size for different stress ratio is suggested. Crack opening loads predicted by the FE analysis based on the procedure suggested resulted in good agreement with experimental ones within the error of 5 %. Effect of the distance behind the crack tip on the crack opening load determined by the ASTM compliance offset method based on the load-displacement relation and by the rotational offset method based on the load-differential displacement relation is investigated. Optimal gage location and method to determine the crack opening load is suggested.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.5 no.4
• /
• pp.1-9
• /
• 2009

It establishes the nonlinear optics material recently on solid-state laser output side and from the infrared ray until is early has in the ultraviolet rays and the wavelength of broadband there makes be a possibility of getting the laser light which and in processing and measuring field it is widely used. Consequently, it used the pulse reiteration law from origination and nine as the fundamental wave direct plan it produced. intense it affixed the nonlinear optics material (KTP) in pulsed light and it got the green light. When inflicting a same energy in respectively reiteration mesh, intense interrelation of pulse light output and green light output between. It analyzed the conversion ratio which it follows in the mesh.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.178.2-178.2
• /
• 2010

The wind turbine gearbox is important rotating part to transmit torque from turbine blade to generator. Generally, gear shaft which rotates causes vibration by influence of stiffness and mass with gear shaft. Root cause of this vibration source is well known to gear transmission error that is decided from gear tooth property. Transmission error excites a gear, and makes excitation force that is vibrated shaft. This vibration of shaft is transmitted to gearbox housing through gearbox bearing. If the resonance about which the natural frequency of the gearbox accords with shaft exciting frequency occurs, a wind turbine can lead to failure. The gearbox for wind turbine should be considered influence of vibration as well as the fatigue life and its performance by such reason. The cause to vibration should be closely examined to reduce influence of such vibration. In this paper, the cause of the vibration which occurs by a gearbox is closely examined and the method which can reduce the vibration which occurred is shown. It is compared with vibration test outcome of a 3MW gearbox for verification of the method shown by this paper.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.253-261
• /
• 2004

A simple and effective filtering method to control the member size of an optimized structure is proposed for topology optimization. In the present approach, the original objective sensitivities are replaced with their relative values evaluated within a filtering area. By adjusting the size of the filtering area, the member size of an optimized structure or the level of its topological complexity can be controlled even within a given finite element mesh. In contrast to the checkerboard-free filter, the present filter focuses on high-frequency components of the sensitivities. Since the present filtering method does not add a penalty term to the objective function nor require additional constraints, it is not only efficient but also simple to implement. Mean compliance minimization and eigenfrequency maximization problems are considered to verify the effectiveness of the present approach.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.6
• /
• pp.343-349
• /
• 2022

This paper proposes a new topology optimization scheme to determine optimized joints for multi-component models. The joints are modeled as zero-length high-stiffness spring elements. The spring joints are considered as mesh-independent springs based on a joint-element interpolation scheme. This enables the changing of the location of the joints regardless of the connected nodes during optimization. Because the joints are movable, the locations of the optimized joints should be aggregated at several points. In this paper, the novel joint dispersal (JD) constraint to prevent joint clustering is proposed. With the joint dispersal constraint, it is possible to determine the optimized joint location as well as optimized topologies while maintaining the minimum distance between each joint. The mechanical compliance value is considered as the objective function. Several topology optimization examples are solved to demonstrate the effect of the joint dispersal constraint.

• Steel and Composite Structures
• /
• v.37 no.6
• /
• pp.663-678
• /
• 2020

This paper proposes a novel topology optimization method generating multiple materials for external linear plane crack structures based on the combination of IsoGeometric Analysis (IGA) and eXtended Finite Element Method (X-FEM). A so-called eXtended IsoGeometric Analysis (X-IGA) is derived for a mechanical description of a strong discontinuity state's continuous boundaries through the inherited special properties of X-FEM. In X-IGA, control points and patches play the same role with nodes and sub-domains in the finite element method. While being similar to X-FEM, enrichment functions are added to finite element approximation without any mesh generation. The geometry of structures based on basic functions of Non-Uniform Rational B-Splines (NURBS) provides accurate and reliable results. Moreover, the basis function to define the geometry becomes a systematic p-refinement to control the field approximation order without altering the geometry or its parameterization. The accuracy of analytical solutions of X-IGA for the crack problem, which is superior to a conventional X-FEM, guarantees the reliability of the optimal multi-material retrofitting against external cracks through using topology optimization. Topology optimization is applied to the minimal compliance design of two-dimensional plane linear cracked structures retrofitted by multiple distinct materials to prevent the propagation of the present crack pattern. The alternating active-phase algorithm with optimality criteria-based algorithms is employed to update design variables of element densities. Numerical results under different lengths, positions, and angles of given cracks verify the proposed method's efficiency and feasibility in using X-IGA compared to a conventional X-FEM.