• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.1
• /
• pp.13-19
• /
• 2014

The feed temperature has an effect on the performance during desalination of seawater by membrane separation. When the permeate flux intends to increase using the waste heat, it is necessary to analyze the effect of feed temperature precisely on the membrane performance. The experiments were carried out to investigate the performance of membranes by varying the seawater temperature from $10^{\circ}C$ to $60^{\circ}C$. The increase of permeate flux with increase of feed temperature was interpreted as the change of water viscosity and the membrane itself. While the increase of permeate flux could be predicted by the viscosity change in case of nanoflitration membrane, there exists 30% difference between the experiment data and the prediction by the viscosity change in case of reverse osmosis (RO) membrane, which seems to be due to 8% decrease of the pore size in 60caused by the contraction of membrane with the increase of temperature. Therefore, the desalination of seawater should be carried out within the range that the elevation of temperature does not cause the alteration of membrane itself even for the purpose of increasing the permeate flux.

• Membrane Journal
• /
• v.4 no.1
• /
• pp.38-45
• /
• 1994

The experiment was conducted to evaluate the effects of variables in preparing TFC membrane by interfacial polymerization. Obtained results are as follow: As the concentration of MPD increses, the rejection rate incresed, the total volume flux was decresed. As the dipping time in MPD solution increases, the rejection rate increased, the total volume flux was increased until reach optimum point. As the dipping time in TMC solution increses, the total volume flux increased, the rejection rate was increased until reach optimum point. As the curing temperature increases, the total volume flux increased was an optimum point in the rejection rate. Since the quantity of generating hydrochloric acid was small, the required quantity of NaOH for neutriliztion was small. The post-treatment with ethanol, isopropanol and water in the temprerature ranging of $5~7^{\circ}C$ brought an increment of the rejection and the total volume flux, For water temperature ranging of $5~7^{\circ}C$was the optimum temperature in the post treatment.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.1
• /
• pp.47-52
• /
• 2005

This study was conducted to evaluate the performance of submerged hollow fiber MF processes to treat secondary wastewater for water reuse. Specifically, membrane productivity and filtrate water quality were investigated under various operating conditions (i.e. flux, recovery, and backwash rate) at pilot-scale. Membrane fouling became more severe with increasing flux and recovery, suggesting that low flux operation (< 25 LMH) was desirable. At high flux operating(> 37.5 LMH), increasing backwash rate showed only limited success. The biofouling, quantified by PEPA and BFHPC, was also significant in wastewater reclamation, and biogrowth control by chlorine, were necessary to improve membrane productivity. Filtrate water qualities are in good compliance with water reuse regulations regardless of operating conditions (flux, recovery and backwash rate). Particle (e.g. turbidity) removal ranged from 89 to 98%, while only 11 to 21% of organics (e.g. NPDOC) were removed by MF membrane. Only small improvement in biostability (e.g. AOC) was achieved by MF system, and thus, without post disinfection, significant microorganisms might be present in the filtrate due to regrowth. Lastly, in order to further investigate pathogen removal, controlled microbial challenge tests were performed by monitoring Giardia, Cryptosporidium, bacteria and virus, and showed relatively good microbial removal.

• Membrane Journal
• /
• v.18 no.2
• /
• pp.168-175
• /
• 2008

This study was carried out for the plate and frame membrane modules equipped with and without plastic protuberances on the support frame in order to determine the effect of eddy flow induced by the protuberances on permeate flux. The initial time for rapidly declined permeate flux on the module with protuberances was delayed twice or more than that on the module without protuberances when kaolin solution was permeated at the operating pressures from 0.4 to 1.6 bar. Also decreasing ratio of the kaolin solution to pure water flux for module with protuberances was 1 to 5% lower than that for module without protuberances. The flux improvement due to protuberances at laminar flow corresponding Reynolds number 1,750 was about double as compared with that in the transition flow region. In general, the kaolin fouling reduction for the plate module with protuberances during initial filtration process was very effective, even though the permeate flux after 60 minutes filtration did not increase significantly.

• Membrane and Water Treatment
• /
• v.7 no.2
• /
• pp.101-113
• /
• 2016

In this study, to improve the water flux of porous hydrophobic membranes, various water-soluble polymers including neutral, cationic and anionic polymers were adsorbed using 'salting-out' method. The adsorbed hydrophobic membrane surfaces were characterized mainly via the measurements of contact angles and scanning electron microscopy (SEM) images. To enhance the durability of the modified membranes, the water-soluble polymers such poly(vinyl alcohol) (PVA) were crosslinked with glutaraldehyde (GA) and found to be resistant for more than 2 months in vigorously stirred water. The water flux was much more increased when the ionic polymers used as the coating materials rather than the neutral polymer and in this case, about 70% of $0.31L/m^2{\cdot}h$ (LMH) to 0.50 LMH was increased when 300 mg/L of polyacrylamide (PAAm) was used as the coating agents. Among the cationic coating polymers such as poly(styrene sulfonic acid-co-maleic acid) (PSSA_MA), poly(acrylic acid-comaleic acid) (PAM) and poly(acrylic acid) (PAA), PSSA_MA was found to be the best in terms of contact angle and water flux. In the case of PSSA_MA, the water flux was enhanced about 80%. The low concentration of the coating solution was better to hydrophilize while the high concentration inclined to block the pores on the membrane surfaces. The best coating condition was found: (1) coating concentration 150 to 300 mg/L, (2) ionic strength 0.15, (3) coating time 20 min.

• Clean Technology
• /
• v.5 no.2
• /
• pp.69-78
• /
• 1999

Separation characteristics of cutting oil-in-water emulsions were studied experimentally by using various kinds of flat-type microfiltration and ultrafiltration membranes. For ultrafiltration membranes the permeation behavior of cutting oil emulsions obeys the film model, whereas a significant deviation from the model was observed for ASYPOR microfiltration membranes. The experimental data obtained for all the membranes showed that the effect of operating pressure on the permeation flux of oil-in-water emulsions is not very significant. At low transmembrane pressures the permeation flux decreased gradually with increasing filtration time, whereas the permeation flux at high transmembrane pressures decreased steeply for early filtration time. However, every flux eventually reached a constant value that depends only on the applied transmembrane pressure. For the hydrophobic polycarbonate microfiltration membrane the permeation flux increased with the filtration time. The critical permeation pressures were also determined from the data obtained from unstirred cell experiments.

• Korean Journal of Food Science and Technology
• /
• v.30 no.2
• /
• pp.397-406
• /
• 1998

Hen egg white lysozyme (HEWL) is very valuable as a natural preservative in food processing due to its selective bactericidal activity. HEWL which traditionally isolated by crystallization or freeze drying was simply separated from 13 different hen egg white (HEW) proteins by a single-step ultrafiltration. Freeze dried HEW (0.25%, w/v) dissolved in a citrate-phosphate buffer (pH 4.6) was ultrafiltered with a PM30 membrane under various operating conditions, by changing concentration, temperature, transmembrane pressure $({\triangle}P_T)$, and stirring speed. Optimum separation conditions were decided when maximal flux was obtained. Under the optimum separation conditions, the effect of membrane material and fouling on flux as time passed as well as lysozyme concentration, protein concentration, specific activity (SA) in the permeate were measured. Best separation conditions of HEWL with PM30 membrane were sample concentration 0.25%, temperature $35^{\circ}C$, ${\Delta}P_T\;30\;psi$, and stirring speed 300 rpm. During the first 12 min, the flux of YM30 was higher, but at the steady-state it was lower than that of PM30. The SA of the PM30 permeate was over 2 times higher in spite of the lysozyme and protein concentration being lower than that of YM30 permeate. The flux of 5 times used PM30 decreased 30% compared to a new PM30, but both had the same tendency in flux decrease when time passed. Both of them reached a steady-state after 35 min and remained at 70% of the initial flux. In the PM30 permeate, the lysozyme concentration and SA were 110 units/mL and 2,821 units/mg protein, respectively. Therefore, PM30 membrane separation was very effective for separation of antimicrobial lysozyme.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.1
• /
• pp.73-80
• /
• 2004

This study investigated the phenomena of membrane fouling by NOM and the effect of the fouling on removal of micro-pollutants. NOM has a great effect on decline of permeate flux. Permeate flow rate was reduced by 88% in RO and 34.8% in NF for 323hr operation period. Removal rate of $UV_{254}$, is 87.4% in RO and 78.5% in NF and removal rate of DOC is 42.7% in RO and 32.9% in NF for 2mg/l humic acid. Removal efficiency of the micro-pollutants by the RO and NF membranes fouled by humic acid was mostly lower than that by the new membrane. The concentration polarization which affects the flux and the rejection was thought to occur in the active layer of the membrane, as the membrane was getting fouled.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.2
• /
• pp.171-176
• /
• 2011

Organic matters that comprise a tiny part of seawater generally occur over 50% of membrane fouling in Reverse Osmosis Process. This study evaluates Foundation efficiency of reverse osmosis membranes under brackish and seawater conditions and resistance of organic fouling. Moreover, analyzing the membrane surface through roughness, contact angle and zeta potential results in roughness and contact angle are proportional to flux decline rate (FDR), yet FDR has high value when zeta potential is low level. Furthermore, with various membrane fouling of different raw water conditions, the flux tends to improve when pH value is high and raw water which is complex with organic and cation pollutes membrane faster than organic separated raw water condition.

• Korean Membrane Journal
• /
• v.5 no.1
• /
• pp.31-35
• /
• 2003

The permeation characteristics of the wastewater containing Si fine particles were examined by ultrafiltration using the polyolefin tubular membrane module. Flux with time was due to the growth of Si cake deposited on the membrane surface and the pore plugging by fine particles. The rate of flux decline in the initial stage increased with the trans-membrane pressure. The pore blocking resistance was the dominant resistance at the initial period of filtration and the cake resistance began to dominate with the initial pore blocking resistance. The larger pores compared with the fine particles, the more the membrane pores could be blocked by the fine particles. Before and after treatment, the distribution of particle size was shifted toward to the left. Then, the average size of fine particles in the permeate was 20 nm.