• Nuclear Engineering and Technology
• /
• v.45 no.3
• /
• pp.335-346
• /
• 2013

The Critical Heat Flux (CHF) of water with dispersed alumina nanoparticles was measured for the geometry and flow conditions relevant to the In-Vessel Retention (IVR) situation which can occur during core melting sequences in certain advanced Light Water Reactors (LWRs). CHF measurements were conducted in a flow boiling loop featuring a test section designed to be thermal-hydraulically similar to the vessel/insulation gap in the Westinghouse AP1000 plant. The effects of orientation angle, pressure, mass flux, fluid type, boiling time, surface material, and surface state were investigated. Results for water-based nanofluids with alumina nanoparticles (0.001% by volume) on stainless steel surface indicate an average 70% CHF enhancement with a range of 17% to 108% depending on the specific flow conditions expected for IVR. Experiments also indicate that only about thirty minutes of boiling time (which drives nanoparticle deposition) are needed to obtain substantial CHF enhancement with nanofluids.

• Elastomers and Composites
• /
• v.25 no.1
• /
• pp.13-19
• /
• 1990

The purpose of this study is to estabilish the synthetic condition of polyurhethane elastomer for excellent properties. Polyurethane elastomer which have different NCO percentage and hard segment contents was synthesized by casting method. And the effects of hard segment contents were investigated by analytical methods such as IR, DSC, etc. [NCO]/[OH] ratio was proper at the range $1.02{\sim}1.05$. By IR absorption peak($1250cm^{-1}$) which indicate interurethane hydrogen bond it was confirmed that hard segment were crystallized. Melting point that was determined by DSC showed the effects of hard segment contents, phase mixing and crystalline size.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.51-67
• /
• 1999

The growth of crystals with high melting points tfus$\geq$1$600^{\circ}C$ faces the researcher with experimental problems, as the choice of materials that withstand such high t is rather limited. Many metallic construction materials are in this high t range already molten or exhibit at least a drastically reduced mechanical strength. The very few materials with tfus》1$600^{\circ}C$ as e.g. W, Mo, and partially even Ir are more or less sensitive against oxygen upon heating. Whenever possible, high t crystal growth is performed under inert atmosphere (noble gases). Unfortunately, any oxides are not thermodynamically stable under such conditions, as reduction takes place within such atmosphere. A thoroughly search for suitable growth conditions has to be performed, that are on the one side "oxidative enough" to keep the oxides stable and on the other side "reductive enough" to avoid destruction of constructive parts of the crystal growth assembly. The relevant parameters are t and the oxygen partial pressure pO2. The paper discusses quantitatively relevant properties of interesting oxides and construction materials and ways to forecast their behavior under growth conditions.r growth conditions.

• Korean Chemical Engineering Research
• /
• v.62 no.3
• /
• pp.253-261
• /
• 2024

The impact of temperature on electrode reactions in 100 cm² molten carbonate cells operating as Fuel Cells (FC) and Electrolysis Cells (EC) was examined using the Reactant Gas Addition (RA) method across a temperature range of 823 to 973 K. The RA findings revealed that introduction of H₂ and CO₂, reduced the overpotential at Hydrogen Electrode (HE) in both the modes. However, no explicit temperature dependencies were observed. Conversely, adding O₂ and CO₂ to the Oxygen Electrode (OE) displayed considerable temperature dependencies in FC mode which can be attributed to increased gas solubility due to the electrolyte melting at higher temperatures. In EC mode, there was no observed temperature dependence for overpotential. Furthermore, the addition of O₂ led to a decrease in overpotential, while CO₂ addition resulted in an increased overpotential, primarily due to changes in the concentration of O₂ species.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.670-675
• /
• 2016

Both melting temperature and enthalpy of MBCA/DMTDA mixtures were measured as a function of DMTDA compositions using DSC. The thermal properties of polyurethane elastomer samples prepared with MBCA, DMTDA, and 40/60 MBCA/DMTDA mixture as curing agents were also observed using TGA. MBCA and DMTDA showed good miscibility over the entire composition range, exhibiting individual DSC melting peaks. Peak temperatures were non-linearly reduced as DMTDA concentrations increased, being approximately $60^{\circ}C$ in the case of the 40/60 MBCA/DMTDA mixture. Furthermore, melting enthalpy of the mixture was calculated as 3.8 J/g, which was only 4.3% compared to 87.3 J/g of MBCA. Based on these results, crystallization of the mixture was considered to occur very slowly, and the fluidic gel-state of the mixture was visually confirmed to be maintained over 5 days at room temperature. Thermal decomposition of polyurethane elastomer prepared with 40/60 MBCA/DMTDA curative started at about $190^{\circ}C$, which is similar to that observed for DMTDA, only except decomposition behavior over higher temperature of $400^{\circ}C$.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.8
• /
• pp.1253-1261
• /
• 2003

This study was carried out to investigate the influences of hydrocolloids on suppression of retrogradation in the Korean rice cake. Hydrocolloids were influenced to the textural characteristics of the Korean rice cake. In particular arabic gum and carrageenan had the effect of suppressing the retrogradation. Cohesiveness of the Korean rice cake added with hydrocolloids was shown to be high compared to control in organoleptic characteristics. Hydrocolloids exhibited slightly effective in retarding surface color change of the Korean rice cake. Onset temperature of gelatinization in thermal characteristics showed somewhat low in case of addition of arabic gum into the Korean rice cake and was followed by carrageenan, guar gum, gelatin and locust bean gum in onset temperature of gelatinization order. All samples added with hydrocolloids had low values in change of melting enthalphy and their range was 12.8 ∼ 17.7 J/g. The Korean rice cake added with arabic gum was lowest in melting enthalphy. The recrystallinity of the Korean rice cake added with arabic gum was greatly low compared to rice cake without hydrocolloids. Melting spreadability of the Korean rice cake added with arabic gum or carrageenan was superior in thermal characteristics. The value of exponent of Avrami was 0.97 ∼ 1.12 in study of Avrami equation. In conclusion carrageenan and arabic gum would have a suppressive effect of retrogradation in the Korean rice cake.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.3
• /
• pp.43-47
• /
• 2001

Sn-3Ag-8Bi-5In was developed for the intermediate melting point solder. Although In-contained solder is expensive, its melting point is lower than these of Sn-Ag-Cu alloys. Sn-3Ag-8Bi-5In solder used for this research has a melting range of 188~$204^{\circ}C$. On this study wetting characteristics of Sn-3Ag-8Bi-5In were evaluated in order to investigate its availability as a Pb-free solder. Wettabilities of Sn-37Pb and Sn-3.5Ag solders were also studied to compare these of the Sn-3Ag-8Bi-5In. Experimental results showed that the zero-cross-time and wetting time at $240^{\circ}C$ for the Sn-3Ag-8Bi-5In were 1.1 and 2.2 second respectively. These values are a little better than these of Sn-37Pb and Sn-3.5Ag solders. The equilibrium wetting farce of the Sn-3Ag-8Bi-5In was 5.8 mN at $240^{\circ}C$, and it was tuned out to be a little higher than that of Sn-3.5Ag and lower than that of Sn-37Pb.

• Economic and Environmental Geology
• /
• v.31 no.3
• /
• pp.249-264
• /
• 1998

The Creataceous volcanic rocks distributed in the southeastern part (Kyeongsang basin) of Korea peninsula are composed of basalt, basaltic andesite, andesite, dacite and rhyolite. The variation of major elements show that contents of MgO, CaO, $FeO^T$, $Al_2O_3$, $TiO_2$ and $P_2O_5$ decrease with increasing of $SiO_2$, but $K_2O$ contents are increased slightly, $Na_2O$ widely dispersed. We can show slightly inflection point and low frequency of dacites in range between 63-65 wt.% $SiO_2$, while continuous trend exit in variation diagram. Variation trends in Harker diagrams for the major, minor, trace and REEs suggest that the BAV (basaltic to andesitic volcanics) and DRV (dacitic to rhyolitic volcanics) are not related to a simple crystal fractionation process. In the regime of under 65 wt. % in silica content, fractionation of olivine and clinopyroxene is predominant, while that of plagioclase happens strongly higher than 65 wt.% (e.g., $SiO_2$, vs. Eu and Sr, MgO vs. $Al_2O_3$ and CaO). The latter means low-pressure fractional crystallization for DRV. On the discriminant diagram, DRV are located in more mature environment than BAV. The $(Ce/Sm)_N$ vs. CeN digram shows that these two classes cannot be related to crystal fractionation. If they had been produced by fractionation, although they plotted in a slightly elongate cluster along the same horizontal trend, DRV should lie to the right of these primitive compositions. These diagrams clearly rule out a simple fractionation throughout from BAV to DRV. BAV had been influenced greatly subductiong slab as shown by K/Yb vs. Ta/Yb. We suggest that BAV primitive magma generated higher degree of partial melting than DRV primitive magma. LILE (K, Ba, $Rb{\pm}Th$) enriched characteristics as shown in BAV are inherited from subducting slab fluids and/or higher degree of partial melting of mantle material. However, lower degree of partial melting of mantle relative to BA V and contamination at high-level magma reservoir caused LILE enrichment to DRV.

• Korean Journal of Heritage: History & Science
• /
• v.36
• /
• pp.241-266
• /
• 2003

Glass pieces excavated from Mireuksa Temple dated $7^{th}$ century A.D. were characterized by chemical composition, specific gravity and melting point. Lead isotope ratios of lead glasses were also compared with those of lead ore to attribute which lead ore was delivered for making lead glass. It was known that some lead glasses found in Japan were similar with those of Mireuksa Temple as comparing the data of chemical composition and lead isotope ratios. Characteristics of lead glass from Mireuksa Temple Thirty five glass pieces of Mireuksa Temple were analyzed for five oxides and found that all was lead glass system(PbO-$SiO_2$) with the range of 70~79% for PbO and 20~28% for $SiO_2$. The concentrations of oxides such as $Al_2O_3$, $Fe_2O_3$ and CuO were below 0.4%, 0.3% and 0.9%, respectively. Principal component analysis(PCA) as a statistical method was carried out to classify glasses with the similarities of chemical concentrations. The result of PCA has shown that three groups of glasses were created according to the excavation positions and two major oxides(PbO and $SiO_2$) greatly contributed to the dispersion of glasses on principal component 1(PC1) axis and trace element oxides($Al_2O_3$ and $Fe_2O_3$) for PC2 axis. Most of lead glasses were greenish by the efficacy of iron and copper oxides and some showed yellowish-green. The gravity of lead glasses was about 4.4~5.4 and estimated melting point was near $670^{\circ}C$. Lead isotope ratios of glasses were analyzed and found quite close to a lead ore from the Bupyeong mine in Gyeonggi-do. Comparison with lead glasses found in Japan Lead glasses of Mireuksa Temple were compared with those of Japan on the basis of chemical and physical data. Chemical compositions of Japanese lead glasses dated $7^{th}{\sim}8^{th}$ century A.D. were nearly similar with those of Mireuksa Temple but lead isotope ratios of those were separated into two groups. Three distribution maps of lead ores of Korea, Japan and China with lead isotope ratios were applied for lead glasses found in Japan. The result have shown that the locations of lead glasses from Fukuoka Prefecture coincided with the region of northen part of Korea and similar with those of Mireuksa Temple and lead glasses from Nara Prefecture dated $8^{th}$ century A.D. were located in the region of Japanese lead ore. This research has demonstrated that lead glasses of Mireuksa Temple conveyed to Miyajidake site, Fukuoka Prefecture around $7^{th}$ century A.D. and glass melting pots and glass beads excavated from Nara Prefecture confirmed the first use of Japanese lead ore for production of lead glasses from the end of $7^{th}$ century A.D.

• Journal of the Korean Ceramic Society
• /
• v.29 no.12
• /
• pp.935-941
• /
• 1992

The LAS system with good thermal properties has a narrow range of firing and sintering temperature near the melting point. So it is difficult to sinter LAS to dense sintered body. In this study, the petalite (Li2O.Al2O3.8SiO2) with good thermal properties, was taken as a base composition, and zironia was added in this composition to broaden the firing range, increase the mechanical strength, and control the thermal expansion. The thermal and mechanical properties were investigated. The results are as follows; 1. Zirconia phase was formed in LAS matrix and apparent porosity was decreased from 0.9% to 0.5%, and the mechanical strength was kincreased from 112 MPa to 190 MPa, by the densification of body. 2. The composition Li2O.Al2O3.8SiO2 has a negative thermal expansion, but the thermal expansion was changed from negative to positive with the densification and the increase of amount of synthesized zircon phase which had positive thermal expansion. The coefficient of thermal expansion, with the increase of the amount of additives, was low as -0.74~9.06$\times$10-7/$^{\circ}C$ in 20~$600^{\circ}C$, and 7.95~20.13$\times$10-7/$^{\circ}C$ in 20~80$0^{\circ}C$. 3. The mechanical strength of LZ15 (added with ZrO2.SiO2 15 wt%) composition thermal-shocked was stable in the temperature range of 0~$600^{\circ}C$, but rapidly decreased due to the increase of thermal expansion above $600^{\circ}C$.