• 한국주조공학회지
• /
• 제12권2호
• /
• pp.149-154
• /
• 1992

The wetting behaviour of SiC/Al-Li composite interface has been investigated by using an infiltration method. The critical pressure for melt infiltration into SiC particulate preform has been determined by measuring the melt infiltration distance changes with the variation of applied pressure. The threshold pressure of pure Al, Al-0.2wt%Li, Al-0.5wt%Li for melt infiltration are 3.94, 3.93, $3.7Kg/cm^2$ respectively, which implies a slight improvement in wettability of SiC/Al composite by addition of Li. The threshold pressure for melt infiltration also changes with the variation of other parameters such SiC particulate size, SiC particulate fraction and melt temperature.

• 한국주조공학회지
• /
• 제24권1호
• /
• pp.34-39
• /
• 2004

The effects of casting condition and hot melt glue during Lost Foam Casting were investigated on the fluidity of Al alloy melt. The fluidity increased linearly with increasing pouring temperature in thick castings but non-linearly in thin casting due to the difference in main heat flow direction. The metal flow velocity was in range of $0.5{\sim}2.7$ cm/s in no evacuation condition and the minimum value of it was measured after the melt flow through the hot melt barrier. The mold evacuation improved the metal flow velocity by around $0.5{\sim}1$ cm/s. And the reaction zone layer thickness was about 1 cm in no-evacuation conditions but about 0.6 cm in mold evacuation condition of 710 torr due to the easier removal of pyrolsis product of EPS. And hot melt barrier thickness of 0.6 mm increased the reaction zone layer thickness up to about 2.5 cm. The fluidity decreased remarkably with an enlarged thickness of hot melt due to a lot of pyrolysis products.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제4권1호
• /
• pp.121-131
• /
• 2000

Melt flow, heat and mass transfer of oxygen have been analyzed numerically in the process of Czochralski single crystal growth of silicon under the influence of misaligned cusp magnetic fields. Since the silicon melt in a crucible for crystal growth is of high temperature and of highly electrical-conducting, experimentation method has difficulty in analyzing the behavior of the melt flow. A set of simultaneous nonlinear equations including Navier-Stokes and Maxwell equations has been used for the modelling of the melt flow which can be regarded as a liquid metal. Together with the melt flow which forms the Marangoni convection, a flow circulation is observed near the comer close both to the crucible wall and the free surface. The melt flow tends to follow the magnetic lines instead of traversing the lines. These flow characteristics helps the flow circulation exist. Mass transfer characteristics influenced by the melt flow has been analyzed and the oxygen absorption rate to the crystal has been calculated and turned out to be rather uniform than in the case of an aligned magnetic field.

• 대한기계학회논문집A
• /
• 제38권7호
• /
• pp.719-725
• /
• 2014

본 연구에서는 사출성형 충전공정 중 금형의 변형을 예측하기 위하여 비뉴턴 유동, 열전달, 구조해석이 함께 고려된 수치해석 연구를 수행하였다. 정밀 사출성형 금형을 설계/제작하기 위해서는 충전공정 중에 발생하는 금형의 변형을 정확하게 예측하는 것이 중요하다. 이와 같은 금형의 국부적인 변형은 다양한 요인에 의해 발생할 수 있으나, 용융된 고분자 수지의 유동에 의한 압력이 가장 큰 원인 중의 하나로 여겨지고 있다. 따라서, 본 연구에서는 2 차원 축대칭 형상의 단순 원형 디스크 제품의 금형을 모델링하고 이에 대한 수치해석을 수행하였다. 이를 바탕으로 금형 내부의 고분자 수지의 유동 특성과 금형 변형량, 온도 분포에 대한 분석을 수행하였다. 또한 다구치 방법을 기반으로 한 실험계획법을 도입하여 유동 속도, 금형 온도, 고분자 수지의 온도가 금형 변형에 미치는 영향을 파악하였다.

• 한국주조공학회지
• /
• 제23권5호
• /
• pp.268-275
• /
• 2003

The mechanism of the hydrogen gas pore formation was investigated in Lost Foam Casting of Al-alloy by reduced pressure test and real casting. The hydrogen gas pick-up was affected by the formed gas during the decomposition of polystyrene in addition to the liquid product. It depended on pouring temperature and a proper temperature of metal front gave the minimum hydrogen pick-up. At a low pouring temperature, the hydrogen went into the melt mainly from entrapped liquid product of polystyrene but pores were formed from the gas as well as the liquid product at a high pouring temperature. The mold flask evacuation down to 710torr decreased the gas porosity down by around 0.4% vol%. The entrapped decomposition product of polystyrene in the melt was observed through the visualization of filling behavior of Al alloy-melt with the high speed camera.

• 한국결정성장학회지
• /
• 제10권6호
• /
• pp.381-388
• /
• 2000

Czochralski 결정 성장 시스템에서 baroclinic 불안정성에 의해 발생하는 유동과 온도 변동에 대해 실험적으로 고찰하였다. 실리콘과 유사한 프란틀 수를 갖는 Wood's metal을 작동유체로 사용하고, 일체형 자석 프로브를 제작하여 멜트의 회전 유속을 측정하였다. 측정 결과 회전 유속은 멜트 바닥에 비해 자유 표면에서 빠르고 특히 결정 근처에서 유속이 증가하는 것을 확인하였다. 또한 도가니 회전 속도를 증가시키면서 속도와 온도 변동을 관찰한 결과 Ro<1.01, Ta>$9.63{\times}10^8$인 영역에서 baroclinic 불안정성이 나타나고, 이 영역에서 유동과 온도가 동일한 주파수를 가지고 변동하였다.

• 한국지능시스템학회논문지
• /
• 제11권6호
• /
• pp.465-469
• /
• 2001

In injection molding short shot is one of the frequent and fatal defects. Experts of Injection molding usually adjust process conditions such as injection time, mold temperature, and melt temperature because it is most economic way in time and cost. However, it is difficult task to find appropriate process conditions for troubleshooting of short shot as injection molding process is a highly nonlinear system and process conditions are coupled. In this paper, a modular fuzzy neural network (MFNN) has been applied to injection molding process to shorten troubleshooting time of short shot. Based on melt temperature and fill time, a reasonable initial mo이 temperature is recommenced by the NFNN, and then the mold temperature is inputted to injection molding process. Depending on injection molding result, specifically the insufficient quantity of an injection molded part. and appropriate mold temperature is recommend repeatedly through the NFNN.

• 한국결정성장학회지
• /
• 제9권4호
• /
• pp.381-383
• /
• 1999

First topic of this paper aims to clarify how oxygen and heat transfer in silicon melt under cusp-shaped magnetic fields. We obtained asymmetric temperature distribution by using time dependent and three-dimensional calculation. Second topic is study on molecular dynamics simulation, which was carried out to estimate diffusion constants of oxygen in silicon melt.

• 한국주조공학회지
• /
• 제24권4호
• /
• pp.217-224
• /
• 2004

The effect of casting variable on the fluidity of high silicon, especially hypereutectic, heat-resistant ductile cast iron melt was investigated. When pouring temperature and silicon content were constant, that was increased with carbon content. When the pouring temperature and carbon content were constant, that also increased with the silicon content. Even though these results were thought to be caused by the high heat of fusion evolved during the crystallization of proeutectic graphite nodules, further research seemed to be needed. The fluidity for taller sprue was higher than that for smaller one.

• 한국세라믹학회지
• /
• 제29권7호
• /
• pp.539-543
• /
• 1992

The continuous growth method was developed for Mn-Zn Ferrite single crystals. It is a new process that the polycrystalline MnχZn1-χFe2O4 raw materials are supplied continuously from the powder feeding system to the crucible heated by R.F. induction and melted in the crucible, and after the single crystals seed is attached to crucible's hole, the crystals are pulled downward with rotation. Growing the crystals by using the growth method different from the conventional Bridgman or Floating Zone method, we defined the factors having effect on the crystal growing through the pre-experiments. They are temperature distribution in the crucible, melt velocity according to its height, wettability between the crucible's bottom and melt. Therefore, Mn-Zn Ferrite single crystals were to be grown by attaining the appropriate melt height in the crucible, powder feeding rate, temperature gradient between the crucible and interface, crystal growing speed, and this method was confirmed to have possibility for single crystal growing.