• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.1
• /
• pp.9-16
• /
• 2008

It is important not only to reduce the casting defects of piston but also to improvement in the mechanical properties(hardness) of piston for the air compressor. The blow hole is typical casting defects in the conventional cast of aluminium alloy(AC8A-T6) piston. Because of the heat treatment method, mechanical properties of the aluminium alloy for piston was decided on the heat treatment method and cycle. Therefore, we tested on the development of mechanical properties and on the casting defects of piston for the air compressor in accordance with the heat treatment and casting condition. After the heat treatment and casting was carried out as several times, and was compared with the imported piston. As a result of several investigations; microstructure, hardness and casting defects of piston was changed under the influence of the heat treatment and casting method. When the cooling rate was controlled and the uni-cast method used, it bas the same mechanical properties and microstructure.

• Fashion & Textile Research Journal
• /
• v.3 no.4
• /
• pp.357-361
• /
• 2001

This paper is concern with the effect of various conditions on mechanical properties of textile fabrics by water soluble resin treatment. Resin treatment of cotton, acetate, viscose rayon, polyester, nylon and acryl fabrics were made by aqueous resin treatment to improve the mechanical properties. The mechanical properties of fabrics, the breaking strength and strain were measured and surface reflectance was measured by color eye. The breaking strength and surface reflectance of fabrics by water soluble resin treatment showed difference by the different treatment concentration. The surface reflectance was increased by water soluble resin treatment. The breaking strength was lower in fabrics with resin treatment than fabrics with none treatment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1561-1570
• /
• 1997

This study explores the treatment of the max-value cost function over a parameter interval in parametric optimization. To avoid the computational burden of the transformation treatment using an artificial variable, a direct treatment of the original max-value cost function is proposed. It is theoretically shown that the transformation treatment results in demanding an additional equality constraint of dual variables as a part of the Kuhn-Tucker necessary conditions. Also, it is demonstrated that the usability and feasibility conditions on the search direction of the transformation treatment retard convergence rate. To investigate numerical performances of both treatments, typical optimization algorithms in ADS are employed to solve a min-max steady-state response optimization. All the algorithm tested reveal that the suggested direct treatment is more efficient and stable than the transformation treatment. Also, the better performing of the direct treatment over the transformation treatment is clearly shown by constrasting the convergence paths in the design space of the sample problem. Six min-max transient response optimization problems are also solved by using both treatments, and the comparisons of the results confirm that the performances of the direct treatment is better than those of the tranformation treatment.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.69-77
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties were decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the In atmospheric gas($H_2$ : 75%, $N_2$ : 25%) and the HNx atmospheric gas($H_2$ : 5%, $N_2$ : 95%) We confirmed the following characteristics, mechanical properties were changed under the influence of the annealing cycle and the atmospheric gas. And, we have some result according to heat treatment method. Elongation of the mechanical properties in the HNx BAF is higher than the Ax BAF. But tensile strength and hardness is higher than the HNx BAF.

• Journal of Mechanical Science and Technology
• /
• v.18 no.12
• /
• pp.2204-2208
• /
• 2004

Ti-8Ta-3Nb has been developed as a new biomaterial. The experimental specimens are as-cast and forged Ti-8Ta-3Nb alloys. Treatment in a solution, ranging from 760 to 960$^{\circ}C$ has carried out. The microstructural research has carried out after the solution treatment and the hardness was measured. The specific heat and the length variations of Ti-8Ta-3Nb were also measured. The optimum temperature for the solution heat treatment of Ti-8Ta-3Nb was found to be 880$^{\circ}C$. This was based on the mechanical properties and the volume fraction of ${\alpha}$ phase and their phases shown from the results of the solution heat treatment. From the results, the ${\beta}$ transition temperature of Ti-8Ta-3Nb was found to be between 860$^{\circ}C$ and 880$^{\circ}C$.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.4
• /
• pp.332-337
• /
• 2013

This paper presents a subsequent research work on the roller design of IRB(isolation roller bearing) seismic isolation device presented in Part 1 by focusing on heat treatment. The hardness and friction factor are very important factors of material and after-treatment process selection. Normally, roller bearing consists of roller and retainer. The roller gets high pressure constantly, while the retainer gets tensile and compressive stress. Therefore, sensitive material selection and heat treatment of each part is quite important. In this experimental evaluation, carbon steel, chrome special steel and others are employed and their characteristics after heat treatment are identified. Each material is prepared by refining high frequency heat treatment. The friction factor and static load capacity of manufactured material are experimentally identified and destructive test of material is processed. Optimal material and heat treatment conditions for IRB roller bearing are determined based on experiment results.

• Korean Journal of Human Ecology
• /
• v.1 no.2
• /
• pp.119-128
• /
• 1998

Nonwoven fabrics for diaper coverstock were treated with chitosan solution by pad-dry method. Two chitosans of different molecular weigh(Mw) with similar degree of deacetylation(DDA) were used: Mw 1,800(chitosan oligomer, DDA 84%). Effect of chitosan treatment on the mechanical properties was investigated using KES-FB system. Primary hand values were calculated from mechanical properties using the same equation as the men's suiting equation with minor modification, and total hand values were calculated using new KN-5LNW equation for nonwoven fabrics developed by Kawabata et al. Increase in chitosan treatment concentration increased B, 2HB, WT, LT and RC, and decreased WC continuously. Chitosan treatment affected other mechanical properties regardless of molecular weight. Considering primary hand values obtained from mechanical properties, it was found that chitosan of Mw 180,000 and chitosan oligomer provided softer, smoother, and more bulky at below 0.05% and above 0.5% treatment concentration respectively. Samples treated with 1.0% chitosan oligomer solution, and 0.01％ chitosan solution of Mw 180,000 showed the best total hand values. (Korean J Human Ecology 1(2):119∼128, 1998)

• Advanced Composite Materials
• /
• v.18 no.3
• /
• pp.221-232
• /
• 2009

The allylamine plasma treatment is used to modify the surface properties of vapor grown carbon fibers (VGCF). It is to improve the interfacial bonding between the VGCF and epoxy matrix. The allylamine plasma process was performed by batch process in a vacuum chamber, using gas injection followed by plasma discharge for the durations of 20, 40 and 60 min. The interdependence of mechanical properties on the VGCF contents, treatment time and interfacial bonding between VGCF/ep was investigated. The interfacial bonding between VGCF and epoxy matrix was observed by scanning electron microscopy (SEM) micrographs of nanocomposites fracture surfaces. The changes in the mechanical properties of VGCF/ep, such as the tensile modulus and strength were discussed. The mechanical properties of allylamine plasma treated (AAPT) VGCF/ep were compared with those of raw VGCF/ep. The tensile strength and modulus of allyamine plasma treated VGCF40 (40 min treatment)/ep demonstrated a higher value than those of other samples. The mechanical properties were increased with the allyamine plasma treatment due to the improved adhesion at VGCF/ep interface. The modification of the carbon nanofibers surface was observed by transmission electron microscopy (TEM). SEM micrographs showed an excellent dispersion of VGCF in epoxy matrix by ultrasonic method.

• Composites Research
• /
• v.26 no.1
• /
• pp.54-59
• /
• 2013

This study deals with effect of plasma treatment on the properties of unidirectional ligno cellulosic fabric Hildegardia Populofolia (HDP) fabric. Thermal stability of the fabric was determined by differential scanning calorimetry (DSC) and Thermo gravimetric analysis (DSC). Morphological properties was analyzed by SEM analysis and found that the surface was rough upon plasma treatment which provides good interfacial adhesion with matrix during composite fabrication. Thermal stability and mechanical properties of the plasma treated fabric slightly increases compare to alkali and untreated fabric. It was observed that tensile properties of the fabric increases upon plasma treatment due to the formation of rough surface. SEM analysis indicates formation of rough surface on plasma treatment which helps in increasing the interfacial interaction between the matrix (hydrophobic) and fabric (hydrophilic).

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.260-263
• /
• 2004

Since Outerrace is one of the components of driving shaft for power train of automobile and transmits high torque, high strength and high toughness are necessary so forging process is adopted to manufacture such parts. Therefore, in order to improve strength and toughness, heat treatment is accomplished after plastic deformation(forging). Because Each component of driving shaft is mounted to automobile after a series of forging, machining and heat treatment, in order to evaluate mechanical properties of such components in use, plastic deformation and heat treatment must be considered. So, in this paper, tensile tests are performed with tensile specimens which have passed through a series of upsetting, machining and heat treatment to evaluate mechanical properties of such components.