• Journal of Biosystems Engineering
• /
• v.14 no.4
• /
• pp.229-241
• /
• 1989

The purposes of this study were to develop an electronic-hydraulic draft control system for tractor implements, to investigate the control performance of the system and the possibility of adaptation to the conventional tractor. Experiments were carried out to investigate the responses of the system to the step and sinusoidal inputs in draft control. The effects of control mode, hydraulic flow rate, reference deadband, and proportional constant on control performance of the system were investigated. Moreover, the effects of filtering signals from draft sensor were also investigated. The following conclusions were derived from the study; 1. In draft control, there were hunting problems in controlling the implement without filtering the draft signals. Filtering was performed by a control program of electronic controller and the control performance and stability of the system were improved significantly. 2. For the draft control system operated on on-off control mode, draft was controlled within ${\pm}27-{\pm}55kg_f$ to the reference draft when the hydraulic flow rates were 5-15 l/min. For the draft control system operated on PWM control, draft was controlled within ${\pm}27kg_f$ to the reference draft regardless of hydraulic flow rates. 3. In the frequency responses of the draft control system, control performance on PWM control mode was not better than on on-off control mode because of characteristics of hydraulic valve and drafe sensor. As the hydraulic flow rates increased for the system operated on on-off control mode, the corner frequency of amplitude attenuation increased, but the corner frequency of phase-angle change remained nearly the same. But, the system was unstable beyond the frequency of 3.1 rad/s. 4. The electronic-hydraulic hitch control system developed in this study showed superior control performance, stability and convenience compared to conventional mechanical-hydraulic hitch control system. It is considered to be a superior replacement for the conventional mechanical-hydraulic hitch control system.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.4
• /
• pp.283-293
• /
• 2015

The effect of the inlet swirling flow in a hydraulic turbine draft tube is a very complex phenomenon, which has been extensively investigated both theoretically and experimentally. In fact, the finding of the optimal flow distribution at the draft tube inlet in order to get the best performance has remained a challenge. Thus, attempting to answer this question, it was assumed that through an automatic optimization process a Genetic Algorithm would be able to manage a parameterized inlet velocity profile in order to achieve the best flow field for a particular draft tube. As a result of the optimization process, it was possible to obtain different draft-tube flow structures generated by the automatic manipulation of parameterized inlet velocity profiles. Thus, this work develops a qualitative and quantitative analysis of these new draft tube flow field structures provoked by the redesigned inlet velocity profiles. The comparisons among the different flow fields obtained clearly illustrate the importance of the flow uniformity at the end of the conduit. Another important aspect has been the elimination of the re-circulating flow area which used to promote an adverse pressure gradient in the cone, deteriorating the pressure recovery effect. Thanks to the evolutionary optimization strategy, it has been possible to demonstrate that the optimized inlet velocity profile can suppress or mitigate, at least numerically, the undesirable draft tube flow characteristics. Finally, since there is only a single swirl number for which the objective function has been minimized, the energy loss factor might be slightly affected by the flow rate if the same relation of the axial-tangential velocity components is maintained, which makes it possible to scale the inlet velocity field to different operating points.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.10 s.241
• /
• pp.1353-1360
• /
• 2005

Injection-molded products serve a wide range of applications in our modem lives and their significance is ever increasing. However, difficulty of communication among related companies under the present system results in increase of lead time and decrease of production efficiency. The objective of this paper is the development of a web-based draft verification system in mold design processes. Although several commercial CAD systems offer draft verification functions, those systems are very expensive and inadequate to perform collaborative works. For collaborative work under the distributed environment, the proposed system uses native file transforming of CAD data into optimal format by using the ACIS kernel and InterOp. Functions of draft verification modules are constructed over the ActiveX control using the visual C++ and OpenGL. Therefore, collaborators related to the development of a new product are able to verify the draft and undercut over the Internet without commercial CAD systems. The system helps to reduce production cost, errors and lead-time to the market. Performance of the system is confirmed through various case studies.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.970-975
• /
• 2008

This study considers indoor thermal comfort in an ondol space by supply vent configurations to prevent cold draft in winter. A specially-designed vent cap has been investigated in comparison with a round pan-type vent and a simple opening without a cap. Numerical simulations have been conducted using CFD to analyze thermal comfort indices such as Predicted Mean Vote (PMV) and Effective Draft Temperature (EDT) as well as air distribution index i.e. Air Diffusion Performance Index (ADPI). Results show the new vent cap provides improved thermal comfort conditions especially near ondol heated floor, as the cold outdoor air spreads upwards along the vertical wall before reaching occupant region near floor. This paper includes discussions on the flow and comfort distributions created by the thermal jets from the vents.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.5
• /
• pp.618-626
• /
• 2012

Suppression of abnormal flow phenomena in the Francis hydro turbine is very important to improve the turbine performance. Especially, as cavitation and cavitation surge makes serious problems when the turbine is operated in the range of partial flow rate, optimum method of suppressing the abnormal flow characteristics is required necessarily. Moreover, as swirl flow in the draft tube of the Francis turbine decreases pressure at the inlet of the draft tube, suppression of the swirl flow can be an useful method of suppressing the occurrence of cavitation. In order to clarifying the possibility of suppressing the swirl flow by J-Groove in the draft tube, a series of CFD analysis has been conducted in the range of partial load, designed condition and excessive flow rate of a Francis turbine. A kind of J-Groove is designed and applied to the draft tube of the Francis hydro turbine model. The pressure contours, circumferential velocity vectors and vortex core regions in the draft tube are compared by the conditions with or without J-Groove. In addition, a group of data about the velocity in the draft is presented to show the influence of J-Groove.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.1
• /
• pp.11-19
• /
• 2015

Recently, the cross flow turbines attract more attention for their good performance over a large operating regime at off design point. This study employs a very low head cross flow turbine, which has open inlet duct and has barely been studied before, to investigate the performance of the cross flow turbine with air suction from the rear part of the runner. Unlike conventional cross flow turbines, a draft tube is attached to the outlet of runner to improve the turbine performance. Water level and pressure in the draft tube are monitored to investigate the influence of air suction. Torque at local blade passage of three parts of runner is examined in detail under the conditions of different air suction. Consequently, it is found that with proper air suction in the runner chamber, the water level in the draft tube gradually drops to Stage 2 of the runner and the efficiency of the turbine can be raised by 10%. Overall, the effect of air-layer on the performance of the turbine is considerable.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.3
• /
• pp.351-357
• /
• 2012

Small hydropower is a reliable energy technology to be considered for providing clean electricity generation. Producing electrical energy by small hydropower is the most efficient contribution to renewable energy. Cross-flow turbine is adopted primarily because of its simple structure and high possibility of applying to small hydropower. The purpose of this study is to investigate the effect of inlet nozzle shape on the performance and internal flow of a cross-flow turbine for small hydropower by CFD analysis. Moreover, the shape effect of draft tube has been investigated according to modified shapes of the length and the diffuse angle. The results show that relatively narrow and converging inlet nozzle shape gives better effect on the performance of the turbine.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.643-648
• /
• 2005

Generally, ships have marks of various shapes on outside of the hull. Among them, so called "Draft Mark" indicates the distance from the bottom of the keel to the waterline. Draft marks are used to determine the displacement and other properties of the ship for stability and control purposes. These marks are made up of welding bead or sticking the steel plate on outside of the hull. To improve the confidence level of the ship owner, quality and accuracy of the draft mark is very important. So the automatic mark welding robot is used to enable a high quality and accurate manufacturing line. To improve the system portability, the system is divided into two distinct parts, namely mechanical part and control part. Mechanical part is robust, a lightweight, and easy to dismantle. The control part consists of an in-house developed controller, which is based on embedded Linux. Also, the control part consists of power line communication module to ensure the applicability of the controller in manufacturing line. In this paper, the methodologies of control and configuration of the robot are discussed.

• Journal of Soil and Groundwater Environment
• /
• v.17 no.1
• /
• pp.42-46
• /
• 2012

The ISO document of ISO/TC/190/SC3/WG11/N11 is a working draft of international standard (WD) dealing with analytical method for the determination of explosives and related compounds using high performance liquid chromatography. The scope of this WD covers the storage of samples, preparing test portion, extraction and instrumentation. The main purpose of this study was to improve the extraction conditions which were already adopted in the WD. For this purpose, mechanical shaking method could be corresponded up to 18 hours of ultrasonic bath extraction in the WD was tested. Methanol was also tested with the intention of being added as an extracting solvent other than acetonitrile in the WD. According to the results, 16 hours of mechanical shaking method showed statistically the same effectiveness as that of 18 hours of ultrasonic bath extraction. In case of extracting solvent, methanol also showed statistically the same extraction capability as acetonitrile for DNB, TNT, 2-A-DNT and 2,4-DNT. However, the recovery rate of TNB with methanol extraction was 40% higher than that of acetonitrile extraction. Through adding mechanical shaking method into committee draft (cf. the next stage draft of the WD during the process for making international standard), ISO standard of analyzing explosives and related compounds in soil would become more useful in dealing with huge number of field samples in the laboratory. In other aspect, adopting methanol as an alternative extracting solvent would be very effective in the terms of exchangeability with GC-ECD/MS method which is being developed by German experts.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09b
• /
• pp.1118-1119
• /
• 2005