• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.270-272
• /
• 1996

This paper describes the dissipation factor measuring techniques of insulating oil on operating pole transformer by using digital signal processor. After applying voltage to the electrodes which is installed in a transformer, acquiring source voltage and current of electrodes and using cross-correlation techniques, we can check the dissipation factor of insulating oil. To improve measuring accuracy and the speed of process, we use hardware such as TMS320C31 DSP board and software such as cross-correlation techniques and rectangular window techniques. We simulated the measuring accuracy and the degree of the noise effect of this new measuring techniques by using computer simulation, and compared the simplified measuring devices with schering bridge on degraded insulating oil. The result showed that this measuring technique can be used as diagnostic method on the pole transformers.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1980-1982
• /
• 1999

Conductive Langmuir-Blodgett(LB) films have recently attracted much interest from the viewpoint of ultrathin film conductors at the molecular level. The result shows that the Maxwell-displacement-current (MDC) measuring technique is useful in the detection of phase-transitions over the entire range of molecule areas. In this parer, electrical properties of PBDG Langmuir(L) films were investigated using a displacement current measuring technique with pressure stimulation. Displacement current was generated When the Spread volume $150{\mu}{\ell}$ and compression velocity was about 30, 40, 50 mm/min. In the result, it is known that current is generated of higher current peek as compression velocity become faster.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.44-52
• /
• 2004

This paper proposed a error compensation methodology for three-DOF translational parallel manipulator. The proposed method uses CMM (coordinate measuring machine) as metrology equipment to measure the position of end-effector. To identify the transform relationships between the coordinate system of the parallel manipulator and the CMM coordinate system, a new coordinate referencing (or coordinate system identification) technique is presented. By using this technique, accurate coordinate transformation relationships are efficiently established. According to these coordinate transformation relationships, an equation to calculate the compensating error components at any arbitrary position of the end-effector is derived. In this paper, Monte Carlo simulation method is applied to simulate the compensation process. Through the simulation results, the proposed error compensation method proves its effectiveness and feasibility.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.3
• /
• pp.217-223
• /
• 2007

This paper introduces an active sensing node using radio-frequency (RF) telemetry. This device has brought the traditional impedance-based structural health monitoring (SHM) technique to a new paradigm. The RF active sensing node consists of a miniaturized impedance measuring device (AD5933), a microcontroller (ATmega128L), and a radio frequency (RF) transmitter (XBee). A macro-fiber composite (MFC) patch interrogates a host structure by using a self-sensing technique of the miniaturized impedance measuring device. All the process including structural interrogation, data acquisition, signal processing, and damage diagnostic is being performed at the sensor location by the microcontroller. The RF transmitter is used to communicate the current status of the host structure. The feasibility of the proposed SHM strategy is verified through an experimental study inspecting loose bolts in a bolt-jointed aluminum structure.

• Journal of information and communication convergence engineering
• /
• v.8 no.1
• /
• pp.83-88
• /
• 2010

Recently car navigation systems which have been widely spread and evolved. The systems use various information and techniques such as real time traffic information and augmented reality technique. In order to provide a shortest path with good flow, real-time traffic information provided by DMB is required. Augmented reality technique is also introduced to give a reality to driver by displaying real images captured by camera during driving. However, these operate well when the system receives GPS data normally. Exact information about the positions of vehicles is a base that supports the above function with realities. This paper proposes a model for acquiring exact position of vehicles. When the GPS does not operate normally, the proposed model uses various data which are generated by integrated vehicle networks.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.1
• /
• pp.73-81
• /
• 2005

A multi-purpose polariscope is developed by applying an electro-mechanical control system to a diffused transmission-type circular polariscope. A conventional polariscope is only good for manual control of optical elements. The new polariscope system is devised to be controlled through two stepping motors and two magnetic clutches. The developed system has both functions of a conventional linear- and circular-polariscope. The new polariscope can be used not only for the point-wise measurement using Tardy compensation technique but also for the full-field fringe analysis using conventional and/or phase measuring techniques, if applicable.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.49 no.3
• /
• pp.69-75
• /
• 2007

Defining the correlations between rural amenities, while difficult, is important for the adequate and efficient development of these amenities. In this research, an Interactional Information Measuring Technique(IIMT) using Information Gathering and Utilizing System(IGUS) was developed to objectively analyze the correlations between abstract ideas. In order to analyze correlations between rural amenities, this model used the Korean Dusan World Encyclopedia as IGUS and the relative interactional information was measured. The correlations between rural amenities were analyzed objectively using IIMT with the results satisfying the basic conditions of interactional information suggested in this research.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10a
• /
• pp.776-779
• /
• 1987

This paper describes a technique for measuring the volume of a pile of powder in a visual way. The volume of a fragile object whose shape is easily transformed by a slight touch of another object must be measured without any contact with it. This can be achieved by applying a three-dimensional shape reconstruction technique employed in computer vision. We have developed a measurement system that finds the volume of a pile of powder by employing a range finder, and performed an experiment of determining the volume of PVC powder piled on a table. The result of the experiment was satisfactory.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.22-24
• /
• 2002

This paper introduces the real-time soil thermal property analyzer and temperature measuring system which is combined with radio telecommunication technique. To measure the thermal parameters in real-time, the radio telecommunication technique are used the personal communication service (PCS) which is in the world-wide serviced commercially firstly by CDMA. The thermal property analyzer has an ability of measuring thermal resistivity, thermal diffusivity and thermal stability. To estimate the soil thermal properties, the curve fitting algorithm by means of the least square method are used. TCP/IP protocol and MTM are used to install the real-time soil thermal property and temperature measurement system at multiple locations along routes of the underground power cables and to reduce the cost of telecommunication.

• Journal of the Ergonomics Society of Korea
• /
• v.17 no.1
• /
• pp.79-89
• /
• 1998

This study describes the research contents, strategies, and applications of simulator for measuring and evaluating human sensibility. The simulator is the integrated experiment facility which can change the physical environment artificially to measure and grasp the reaction feature of human sensibility for the products and environments. The design technique consists of two parts; development of technique to present the mock environment related to sensibility elements and development of software to measure and evaluate sensibility physiologically and psychologically. The simulator can be utilized for evaluating the main industrial products and environments. Therefore, the simulator can increase the added-value of the product and environment, and also contribute to the improvement of quality of human life.